Adding coolant
When adding coolant, make sure it is a 50/50 mixture of coolant and
distilled water. Add the mixture to the coolant reservoir,when the
engine is cool, until the appropriate fill level is obtained.
WARNING:Do not add coolant when the engine is hot. Steam
and scalding liquids released from a hot cooling system can burn
you badly. Also, you can be burned if you spill coolant on hot engine
parts.
WARNING:Do not put coolant in the windshield washer fluid
container. If sprayed on the windshield, coolant could make it
difficult to see through the windshield.
•DO NOT MIX different colors or types of coolant in your vehicle. Make
sure the correct coolant is used. DO NOT MIX recycled coolant and
conventional coolant together in the vehicle. Mixing of engine coolants
may harm your engine’s cooling system. The use of an improper
coolant may harm engine and cooling system components and may
void the warranty. Refer toMaintenance product specifications and
capacitiesin this chapter.
Note:Do not use stop leak pellets or cooling system sealants/additives
as they can cause damage to the engine cooling and/or heating
systems. This damage would not be covered under your vehicle’s
warranty.
•A large amount of water without coolant may be added, in case of
emergency, to reach a vehicle service location. In this instance, the
cooling system must be drained and refilled with a 50/50 mixture of
coolant and distilled water as soon as possible. Water alone (without
coolant) can cause engine damage from corrosion, overheating or
freezing.
•Do not use alcohol, methanol or brine or any engine coolants
mixed with alcohol or methanol antifreeze (coolant).Alcohol
and other liquids can cause engine damage from overheating or
freezing.
•Do not add extra inhibitors or additives to the coolant.These
can be harmful and compromise the corrosion protection of the engine
coolant.
Maintenance
27
2012 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)
After any coolant has been added, check the coolant concentration (refer
to theMaintenance and Specificationschapter of yourOwner’s
Guide).If the concentration is not 50/50 (protection to –34°F/–36°C),
drain some coolant and adjust the concentration. It may take several
drains and additions to obtain a 50/50 coolant concentration.
Whenever coolant has been added, the coolant level in the coolant
reservoir should be checked the next few times you drive the vehicle. If
necessary, add enough 50/50 concentration of coolant and distilled water
to bring the liquid level to the proper level.
If you have to add more than 1.0 quart (1.0 liter) of coolant per month,
have your dealer check the cooling system. Your cooling system may
have a leak. Operating an engine with a low level of coolant can result in
engine overheating and possible engine damage.
ENGINE SPARK PLUG INTERVAL
To keep your high performance engine operating at peak performance,
the spark plug service interval is every 45,000 miles (72,000 km).
Reference the MotorcraftPart Numbers chart for the specific spark
plug application.
OCTANE RECOMMENDATIONS
Your vehicle is designed to run on
Premium fuel with an (R+M)/2
octane rating of 91 or higher. For
best overall performance, SVT
recommends using Premium fuel
with an (R+M)/2 octane rating of 93 or higher where available. The
performance gained by using higher octane fuel will be most noticeable
in hot weather or in severe duty applications.
Recommended fuel is an important part of the proper maintenance and
optimal performance of this vehicle. The use of gasoline with an (R+M)/2
octane rating lower than 91 can lead to severe mechanical damage to
your vehicle, may degrade vehicle performance, and may affect your
warranty coverage. Please see the Warranty Guide for complete
information.
SVT does not recommend the use of gasolines labeled asPremiumwith
(R+M)/2 octane ratings less than 91.
91(R+M)/2 METHOD
Maintenance
29
2012 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)
