2012 FORD MUSTANG weight

Performance gauge- performs the following functions:
•Real time mode – measures G
force/acceleration (Note:
Requires initial calibration) See
Setup information.
•1/4 mile data including reaction
time
•0-60 mph times
•60-0 mph distances
•Horsepower -Note:This reading
will vary from advertised engine horsepower. It includes losses
through the drivetrain and other factors such as fuel octane, wind,
weight, road grade, etc.
•Setup
This gauge is intended for off-road use only (racetracks or other
controlled courses or settings).
Real time mode:
The performance gauge calculates/displays acceleration and G-forces
while in real time mode. The customer is required to calibrate/initialize
the performance gauge to ensure proper acceleration measurements
while in real time mode (see Setup section). At vehicle start up, the
performance gauge defaults to real time mode. The gauge stays in real
time mode until the user selects one of the other five operating modes.
The gauge returns to real time mode after exiting the operating modes.
In real time mode, the gauge will display the driver’s choice of
acceleration/deceleration or lateral g-forces on an LED graph and display.
Acceleration forces will be displayed on the bar graph to the right of
center. Deceleration forces will be displayed on the bar graph to the left
of center.
•Press B to change the display to the lateral axis.
•See bar graph forward/lateral high/low under Setup to change the
range of g-forces capable of being displayed on the LED.
Peak Recall – While in any mode, the gauge will record the highest
g-force values for all four axes (accel, decel, left and right).
•Press C to view these values.
•Press A to move to the next value.
•Press B to clear the value.
Boss302 Unique Features
10
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)

Horsepower mode-Note:This reading will vary from advertised
engine horsepower. It includes losses through the drivetrain and other
factors such as fuel octane, wind, weight, road grade, etc. In order to
obtain the most accurate numbers, it is important that the correct
vehicle weight be stored in the gauge (see Setup section). The gauge has
been preset with the weight preset to 3830 lb (1737 kg) and should be
modified as needed. To select horsepower mode, do the following:
1. Press MODE until “HP” (horsepower) is displayed.
2. Make sure the vehicle is at a complete stop at the beginning of your
course, then press ENTER to confirm. The display will show “CAL” to
indicate mode has been entered.
When the display reads “Go”,
1. Lightly accelerate your vehicle through first gear.
2. Shift between gears at approximately halfway to redline.
3. In second gear, (ideally at 2,000 rpm) accelerate under full throttle up
to, but not exceeding, the engine redline.
4. Let off the accelerator and safely stop the vehicle to view your results
once redline has been reached.
5. The gauge will display your horsepower results. Press B to view your
results again. See the section on viewing best run/last run/etc results.
Setup mode:(There are eight parameters that can be adjusted in Setup
mode).
To select Setup mode, do the following:
1. Press the mode button until “Sup” is displayed.
2. Press the enter button to confirm.
3. Press the exit (C button) to exit setup mode.
Vehicle calibration:
Performing this operation will be necessary in order to obtain correct
readings from the performance gauge while operating in real time mode
and performance modes. The vehicle calibration function allows the
gauge to determine its angle, pitch, and general location in your vehicle,
and to compensate accordingly, allowing you to mount it virtually
anywhere in any position, and still get accurate readings.
To select vehicle calibration mode, enter Setup as described above, then
press the A button until “VCAL” is displayed, then press ENTER to
confirm. “REDY” should display. Bring the vehicle to a complete stop on
a flat and level surface and then press ENTER. “HOLD” will display. At
Boss302 Unique Features
14
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)

Vehicle weight:Accurate weight is necessary for the gauge to make a
valid horsepower calculation. The vehicle weight has been preset to
3830 lb (1737 kg).
To enter/modify vehicle weight, do the following:
1. Repeatedly press the MODE button until “SUP” is displayed.
2. Press ENTER to confirm.
3. Press A until “ULBS” is displayed.
4. Press ENTER to confirm. The value displayed is total vehicle weight in
pounds (lb). To increase the value, either press or press and hold the A
button. To decrease, press or press and hold the C button. Weight is
adjusted in ten pound increments and can be set to any value from
500 lb (227 kg) to 8,000 lb (3629 kg).
5. When the correct value is reached, press B to confirm.
6. To exit and return to real time display, press EXIT (C button). A
lower than actual weight setting will result in a lower than expected
horsepower reading. The opposite is true with a higher than actual
weight setting.
Bar graph forward high setting:
The bar graph forward high mode allows you to adjust the G force scale
for forward acceleration as shown on the gauge when operating on the
forward axis in real time mode. For example, if you set the “bGFH” to
1g, when the bar is fully lit on the right hand (acceleration) side, the
vehicle is achieving 1g of acceleration force or more.
To select bar graph forward high mode, enter Setup, then press the A
button until “bGFH” is displayed. Press ENTER to confirm. The current
setting should be displayed, and can be adjusted up and down from .3 to
2.0 G’s using the A and C buttons. When the desired result is displayed,
press ENTER to confirm. The bar graph high setting is preset to 0.7G.
Bar graph forward low setting:
The bar graph forward low mode allows you to adjust the G force scale
for rearward acceleration (deceleration or braking) as shown on the
gauge when operating on the forward axis in real time mode. For
example, if you set the “bGFL” to 1g, when the bar is fully lit on the left
hand (deceleration) side, the vehicle is achieving 1g of force or more
during braking.
Boss302 Unique Features
16
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)

WARNING:When a wheel is installed, always remove any
corrosion, dirt or foreign materials present on the mounting
surfaces of the wheel or the surface of the wheel hub, brake drum or
brake disc that contacts the wheel. Ensure that any fasteners that
attach the rotor to the hub are secured so they do not interfere with
the mounting surfaces of the wheel. Installing wheels without correct
metal-to-metal contact at the wheel mounting surfaces can cause the
wheel nuts to loosen and the wheel to come off while the vehicle is in
motion, resulting in loss of control.
IMPORTANT TIRE INFORMATION
Your vehicle is equipped with unique wheels and tires designed to
enhance performance. To continue providing this performance, extra
care must be taken when operating and maintaining your vehicle.
Wheels and tires
Boss30219in.x9.0in.front,19in.x9.5in.rear
cast aluminum wheels
255/40ZR19 front, 285/35ZR19 rear tires
Boss302 with
Laguna Seca
Package19 in. x 9.0 in. front, 19 in. x 10.0 in. rear
lightweight cast aluminum wheels
255/40ZR19 front, 285/35ZR19 rear tires
(ultra high performance)
Tires
Your Boss302 is equipped with low profile, high performance tires that
are designed to optimize the car’s driving dynamics. These tires are not
optimized for off-road or winter (snow or cold weather) performance,
and their ride, noise and wear characteristics are different than
non-performance tires. Also, because of their lower profile, the tires are
more susceptible to damage due to potholes and rough roads. To ensure
that your tires perform as intended, it is important that you maintain
your tires properly.
•The Boss302 and Boss302 with Laguna Seca Package original
equipment tires are optimized for maximum steering and handling
performance. Ford does not recommend using these tires in cold
temperatures of approximately 40°F (5°C) and below (depending on
tire, surface and weather conditions). See your Ford dealer for
recommended tires in these conditions.
Tire Information
23
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)

•The Boss302 with Laguna Seca Package is equipped with ultra
high-performance, dry weather-only summer tires that provide
superior steering and handling.
WARNING:If equipped with the Laguna Seca Package, never
drive with these tires in any wet conditions (rain, snow, ice, etc.)
because they cannot channel water away and will slide risking serious
injury.
•Do not use tire chainson the original wheels and tires of your
vehicle. The use of any type of tire chain on these tires may damage
your vehicle.
•Always maintain your tire pressures according to the tire information
placard on the driver’s door jamb, using an accurate gauge.
•Tire pressures are specified “cold” and should be checked after the
vehicle has been parked for at least 3 hours. Do not reduce pressure
of warm tires.
•Check your tire pressure often to maintain it properly. Tire pressure
can diminish over time and fluctuate with temperature.
•Do not overload your vehicle. Maximum vehicle and axle weights are
listed on the tire information placard.
•Extra caution should be taken when operating the vehicle near its
maximum load, including assuring proper tire pressure and reducing
speeds.
•Extra caution should be taken when operating on rough roads to avoid
impacts that could cause tire damage.
•In the event that you encounter an abnormally harsh impact, inspect
your tires for damage.
•Inspect your tires for damage on a regular basis. If a tire is damaged,
replace it immediately.
•Proper suspension alignment is critical for maximum performance and
optimal tire wear. If you notice uneven tire wear, have your alignment
checked.
Tire Information
24
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)

MOTORCRAFT PART NUMBERS
Component Boss 302 engine
Engine drivebelt JK6-678
Lightweight battery BXT-96R-500
ENGINE OIL RECOMMENDATION
Use MotorcraftSAE 5W-50 full synthetic or an equivalent SAE 5W-50
full synthetic oil meeting Ford specification WSS-M2C931-B.
Do not use supplemental engine oil additives, cleaners or other engine
treatments. They are unnecessary and could lead to engine damage that
is not covered by Ford warranty.
Change your engine oil and filter according to the appropriate schedule
listed in thescheduled maintenance information.
Maintenance and Specifications
31
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)

USING THE RIGHT BULBS
Function Trade number
Headlamp H13
DRIVETRAIN
Item Description
Rear axle8.8 in. solid rear axle with limited-slip
differential 3.73:1 ratio
Driveshaft2-piece steel
TransmissionMT82 6-speed manual with integral clutch
housing
Gear ratiosGear Ratio
1st 3.66
2nd 2.43
3rd 1.69
4th 1.31
5th 1.00
6th 0.65
Reverse 3.32
ENGINE INFORMATION
Item Description
Configuration90-degree V8
Aluminum block
Aluminum high flow cylinder
heads
Engine weight - 444 lb. (201 kg)
Bore x stroke92.2 x 92.7 mm
(3.63 x 3.65 inches)
Displacement302 cubic inches (5.0L)
Compression ratio11.0:1
Maintenance and Specifications
34
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)

Item Description
Valve trainCompact RFF (roller finger
followers)
Four valves per cylinder
Cam timingTwin independent variable
Fuel systemSequential mechanical returnless
fuel injection
Ignition systemCoil on plug, two knock sensors
Firing order1–5–4–8–6–3–7–2
Throttle bodySingle bore 80 mm
PistonsForged aluminum
CrankshaftFully counterweighted forged steel
Connecting rodsHigh strength forged powder
metal/floating pin
Intake manifoldRunners in a box composite
Exhaust manifoldsPulse separated stainless steel
tubular headers
Engine drivebelt routing
1. Short drivebelt is on first pulley groove closest to engine.
2. Long drivebelt is on second pulley groove farthest from engine.
12
Maintenance and Specifications
35
2012 05+ Mustang(197)
Supplement, 2nd Printing
USA(fus)