2012 FORD B MAX headlamp

Downloaded from www.Manualslib.com manuals search engine Message Centre Indicator
It will illuminate when a newmessage is stored in theinformation display. SeeInformation Messages (page 62).
Oil Pressure Warning Lamp
WARNING
Do not resume your journey if itilluminates despite the level beingcorrect. Have the system checked byan authorised dealer immediately.
If it stays on after starting orilluminates when driving, thisindicates a malfunction. Stopyour vehicle as soon as it is safe to do soand switch the engine off. Check the engineoil level. See Engine Oil Check (page 139).
Power Steering Warning Lamp
Illuminates to indicate amalfunction of the powersteering system. You willcontinue to have full steering but will needto exert greater force on the steeringwheel. Have the system checked by anauthorised dealer as soon as possible.
Rear Fog Lamp Indicator
It will illuminate when you switchthe rear fog lamps on.
Seat Belt Minder Warning Lamp
It will illuminate when a seat beltis not fastened. See Seat BeltMinder (page 21).
Shift Indicator
It will illuminate to inform youthat shifting to a higher gear maygive better fuel economy andlower CO2 emissions. It will not illuminateduring periods of high acceleration, brakingor when the clutch pedal is pressed.
Stability Control Indicator
While driving, it flashes when thesystem is operating. After youswitch the ignition on, if it doesnot illuminate or illuminates continuouslywhile driving, this indicates a malfunction.During a malfunction, the system switchesoff. Have the system checked by anauthorised dealer as soon as possible.
If you switch the electronic stabilityprogram off, the warning lamp willilluminate. The lamp will go out when youswitch the system back on or when youswitch the ignition off.
AUDIBLE WARNINGS AND
INDICATORS
Automatic Transmission
Sounds when you open the driver's doorand do not move the transmission selectorlever to position P.
Key Outside Car
Vehicles With Keyless System
Sounds when you close the door, theengine is running and the system does notdetect a passive key inside your vehicle.
Headlamps On
Sounds when you remove the key from theignition and open the driver's door and youhave left the headlamps or parking lampson.
56Instrument Cluster

Downloaded from www.Manualslib.com manuals search engine 4.Connect the negative (-) terminal ofvehicle B to the ground connection ofvehicle A (cable D).
WARNINGS
Do not connect directly to thenegative (–) terminal of the flatbattery.
Make sure that the cables are clearof any moving parts and fuel deliverysystem parts.
To Start the Engine
1.Run the engine of vehicle B at amoderately high speed.
2.Start the engine of vehicle A.
3.Run both vehicles for a minimum ofthree minutes before disconnecting thecables.
WARNING
Do not switch on the headlampswhen disconnecting the cables. Thepeak voltage could blow the bulbs.
Disconnect the cables in the reverse order.
123Roadside Emergencies

Downloaded from www.Manualslib.com manuals search engine Passenger's Compartment Fuse Box - Type 1
Circuits protectedFuse ratingFuse
Ignition, rain sensor, heatedwindscreen7.5 A1
Stop lamps10 A2
Reversing lamp, rear viewcamera7.5 A3
Headlamp levelling7.5 A4
Not used-5
Rear window wiper15 A6
Washer pump15 A7
Not used-8
Passenger's heated seat15 A9
Driver's heated seat15 A10
Not used-11
Airbag module10 A12
128Fuses

Downloaded from www.Manualslib.com manuals search engine Passenger's Compartment Fuse Box - Type 2
Circuits protectedFuse ratingFuse
Ignition, rain sensor, heatedwindscreen, dome lamp,interior mirror7.5 A1
Stop lamps10 A2
Reversing lamp7.5 A3
Headlamp levelling7.5 A4
Not used-5
130Fuses

Downloaded from www.Manualslib.com manuals search engine Changing the Windscreen Wiper Blades
1.Press the locking buttons together.
2.Rotate and remove the wiper blade.
3.Install in the reverse order.
Note:Make sure that the wiper blade locksinto place.
Rear Window Wiper Blade
1.Lift the wiper arm.
2.Position the wiper blade at right anglesto the wiper arm.
3.Disengage the wiper blade from thewiper arm.
4.Remove the wiper blade.
5.Install in the reverse order.
Note:Make sure that the wiper blade locksinto place.
REMOVING A HEADLAMP
1.Open the bonnet. See Opening andClosing the Bonnet (page 134).
2.Remove the screws and push pins.
3.Lift the outer side of the headlamp todisengage it from the lower fixing point.
4.Pull the headlamp as far as possibletoward the centre of your vehicle andremove.
142Maintenance

Downloaded from www.Manualslib.com manuals search engine 5.Disconnect the electrical connector.
Note:When fitting the headlamp, makesure that you reconnect the electricalconnector correctly.
Note:When fitting the headlamp, makesure that you fully engage the headlamp inthe lower fixing point.
CHANGING A BULB
WARNINGS
Switch the lamps and the ignition off.
Let the bulb cool down beforeremoving it.
Do not touch the glass of the bulb.
Note:Only fit bulbs of the correctspecification.
Note:The following instructions describehow to remove the bulbs. Fit replacementsin the reverse order unless otherwise stated.
Headlamp
Note:Remove the covers to gain access tothe bulbs.
Headlamp main beamA
Headlamp dipped beamB
Direction indicatorC
Direction Indicator
1.Remove the headlamp. SeeRemoving a Headlamp (page 142).
2.Turn the bulb holder anticlockwise andremove it.
143Maintenance

Downloaded from www.Manualslib.com manuals search engine 3.Gently press the bulb into the bulbholder, turn it anticlockwise andremove it.
Headlamp Main Beam
1.Remove the headlamp. SeeRemoving a Headlamp (page 142).
2.Remove the cover.
3.Disconnect the electrical connector.
4.Release the clip and remove the bulb.
Note:Do not touch the glass of the bulb.
Headlamp Dipped Beam
1.Remove the headlamp. SeeRemoving a Headlamp (page 142).
2.Remove the cover.
3.Turn the bulb holder anticlockwise andremove it.
4.Remove the bulb.
Note:Do not touch the glass of the bulb.
Side Lamp
1.Remove the headlamp. SeeRemoving a Headlamp (page 142).
2.Remove the cover.
3.Remove the bulb holder.
4.Remove the bulb.
Side Repeater
144Maintenance

Downloaded from www.Manualslib.com manuals search engine Luggage Compartment Lamp,Footwell Lamp and Liftgate Lamp1.Carefully prise out the lamp.
2.Remove the bulb.
BULB SPECIFICATION CHART
Power (watt)SpecificationLamp
21PY21WFront direction indicator
55H1Headlamp main beam - high series
55H15Headlamp main beam - low series
551H7Headlamp dipped beam
55H11Front fog lamp
5W5WSide lamp - low series
5WY5WSide repeater
5W5WApproach lamp
21PY21WRear direction indicator
21/5P21/5WBrake and rear lamp
21H21WRear fog lamp
21P21WReversing lamp
149Maintenance