Page 71 of 278
69
Seats
EASE OF USE and COMFOR
T
3
- an active adjustment: operate the handle
upwards or downwards until the desired
position is reached.
Head restraint height adjustment
To raise or lower the restraint, pull it
forwards, then slide it. The adjustment is correct when the upper
edge of the head restraint is level with the
top of the head.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
Front heated seat controls
Adjustable armrest
To place the armrest in its rest position:
- raise it until it is in the centreline of the
seat back.
4 - Driver's seat lumbar adjustment
Move the lever up or down to obtain the
required position. To remove it, set it in the high position, press
the tabs and pull upwards and forwards at
the same time.
To re-install, engage the head restraint rods
in the holes, making sure they are aligned
with the seat back.
To place the armrest in a position for use:
- fold it down fully,
- raise it slowly to the required position,
- if you pass the required position, raise it
fully then repeat the operations above.
Press the corresponding control,
located on the overhead storage
unit.
The temperature is controlled
automatically.
Pressing a second time stops operation.
Page 72 of 278
70
Seats
2-SEAT FRONT BENCH
If your vehicle is fitted with this bench seat,
it is fixed and has a 3rd seat belt.
Head restraint
Press the tab to adjust the height of the
head restraint.
To remove the head restraint, press the tabs
and raise the head restraint.
The adjustment is correct when the upper
edge of the head restraint is level with the
top of your head.
Never drive with the head restraints
removed; they must be in place and
adjusted correctly.
Seat back pockets
If your vehicle is fitted with these, they are
located on the backs of the front seats.
Page 74 of 278
72
Seats
REAR SEATS
The type of rear seats depends on the
version and configuration of your vehicle.
The individual seat is always located
on the right-hand side and the bench on
the left-hand side (in the direction of travel).
Page 75 of 278
Seats
EASE OF USE and COMFOR
T
3
Type 2:
an individual seat the back of which
can be folded to the table position then
raised, facilitating access to the rear space.
Individual passenger seat
This seat and the 2-seat bench are
interdependent. Any handling operation
must begin with the individual seat.
Two models are offered:
Two-seat bench
Three models are offered:
Type 1:
an individual seat which can be
raised permitting access to the rear space.
Type 1:
a two-seat cushion with fixed seat
back.
Page 76 of 278
74
Seats
Type 2:
two seats with folding seat backs
and seat cushion which can be raised.
Type 3:
a two-seat cushion with individual
tilting seat backs which can be folded to the
table position and cushion which can be
raised.
Specifications depending on the
type of seat
Seat fitted with this control: the seat back
can be tilted.
Seat fitted with this control: the seat back
can be tilted and raised. Seat fitted with this control: the seat back
can be folded and coupled with the raising
control.
"Comma" shape head restraint.
Page 77 of 278
Seats
EASE OF USE and COMFOR
T
3
This armrest may be fitted.
The seat backs of the outer seats are fitted
with a storage net. The seat backs of the centre seats are
designed with cup holder and storage
recesses.
Page 78 of 278
76
Seats
Handling
Folding the seat back to the table position
(centre seat example)
- Place the head restraints in the low
position.
- Raise this handle to unlock the seat
back (from the rear, lower the handle).
- Tilt the seat back onto the seat cushion.
Seat and bench of type 1:
- Raise the seat.
Seat and bench of type 2/type 3:
- Fold the seat back to the table position
using this handle.
- Raise the seat.
- Unlock the front feet using this handle.
- Disengage the seat from its anchorages.
- Remove the seat from the vehicle via
the side door in row 2 and via the rear in
row 3.
- Unlock the front feet using this handle.
- Disengage the seat from its anchorages.
- Remove the seat from the vehicle via
the side door in row 2 and via the rear in
row 3.
Enter, exit the vehicle: raise the seat
Always start with the individual seat located
on the right-hand side and place the head
restraint in the low position.
Page 79 of 278
77
Seats
EASE OF USE and COMFOR
T
3
Installing the seat
Always install the bench first.
- Check that there are no objects
obstructing the anchorages and
preventing correct locking of the feet.
- Engage the front feet in the anchorages
on the floor.
- Lock the front feet using this handle.
- Tilt the seat towards the rear until the
rear feet lock. Be aware of the feet of
passengers when tilting. For the type 2 seat and the type 2/3 bench:
fold up the seat back.
Correct anchoring of the front feet
Check that the seat is locked correctly
on the floor when it is returned to the
sitting position.
