Page 34 of 348
Warning/indicator lampStateCauseAction/Observations
Automatic
wiping
fixed. The wiper control is pushed
downwards.
Automatic front wiping is activated.
To deactivate automatic wipin
g, operate the controlstalk downwards or put the stalk into another position.
Passenger's airbag systemfixed in the seat beltand passenger's front airbag warning lamps
display.
The control switch, located in
the glove box, has been placed in
the "ON"
position.
The passenger's front airbag is activated.In this case, do not install a "rear facing" child seat.
Move the control switch to the "OFF"
position to
deactivate the passenger's front airbag.
In this case, you can install a "rear facing" child seat.
Stop & Startfixed. When the vehicle stops (red lights,
traffic jams,...) the Stop & Star tsystem has put the engine into STOPmode.The warnin
g lamp goes off and the engine restarts
automatically in START mode, as soon as you want tomove off.
fl
ashes for a few seconds, then goesoff. ST
OP mode is temporarily unavailable. or STA R T mode is invokedautomatically. Refer to "Drivin
g - § Stop & Star t" for special cases
with STOP mode and STA R T m o d e .
Page 44 of 348
System for manual adjustment of the brightness of the instruments and controls in relation to
the exterior brightness.
Lighting dimmer
Activation
When the lighting is on:
)press the button to change the brightness
of the instruments and controls, )when the level of brightness required isreached, release the button.
Deactivation
When the lighting is off, or in day mode on
vehicles fitted with daytime running lamps,pressing the button does not have any effect.
System which measures the total distance
travelled by the vehicle during its life.
The total and trip distances are displayed for
thir ty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked.
Total distance recorder
System which measures a distance travelledduring a day or other period since it was reset
to zero by the driver. ) With the ignition on, press the button until
zeros appear.
Trip distance recorder
To c o nform to legislation in the countryyou are crossing, change the units of distance (miles or km) via the configuration menu.
Page 50 of 348
Electronic key
remote control
Unlocking the vehicle
Complete unlocking
Selective unlockin
g Unlocking the boot
System which permits central unlocking or
locking of the vehicle using the lock or from adistance. It is also used to locate and start thevehicle, as well as providing protection against
theft.
This settin
g is done in the configuration menu.
Complete unlocking is activated bydefault.
Unlocking is confirmed by rapid flashing of the direction indicators for around two seconds.
At the same time, depending onversion, the door mirrors unfold.
Locking the vehicle
Locking is confirmed by fixed lighting of the direction indicators for approximately two seconds.
The door mirrors fold at the same time.
)To u n l o c k o n ly the driver's door,press the open padlock once. )Press the closed padlock to lock
the vehicle completely. Hold the button down until the
windows close completely.
)
Press this button until you hear
th
e boot unlock. The vehicle is completely unlocked.
Be aware of children when operatingthe windows.
)
Press the open padlock to unlock
the vehicle.
) To unlock the other doors and the boot,
press the open padlock again.
Page 52 of 348
Locking the vehicle
)With the electronic key in the definedzone A , press with a finger on one of
the door handles (at the markings) to lock
the vehicle.
Maintain pressure with your finger until
the windows close completely.
Locking is confirmed by fixed lighting of the direction indicators for approximately two seconds.The door mirrors fold at the same time.
If one of the doors or the boot is still open or if the key for Keyless Entry and Starting has been left inside the vehicle,the central locking does not take place.
When the vehicle is locked, if it isunlocked inadvertently, it will relockautomatically after about thir ty secondsunless a door is opened.
The folding and unfolding of the door mirrors by the remote control can bedeactivated by a CITROËN dealer or a qualified workshop.
As a safety measure (children onboard), never leave the vehicle without taking the key for the Keyless Entry andStarting system, even for a shor t period.Guard against theft when the key for the Keyless Entry and Starting systemis in the defined zone with the vehicle unlocked. After a long period of parking, the automatic detection functionsof the key are inhibited so as to notdischarge the vehicle's battery. You
should then use the remote controlfunction of the key to unlock the vehicle.
Ensure that no one prevents the correct operation of the windows.Be aware of children when operatingthe windows.This
function allows you to identify your vehicle from a distance, particularly in poor light. Your vehicle must be locked.
Locating your vehicle
)Press the closed padlock on the remotecontrol.
This will switch on the cour tesy lamps and thedirection indicators will flash for a few seconds.
Page 63 of 348
61Access
Cockpit glass roof
Component which has a tinted glass panoramic sur face to increase the light and visibility in thepassenger compartment.
Fitted with three electric blinds to improve
tem
perature and noise related comfort. There are two options for openin
g and closing:
Electric blinds
) Pull or press control, going beyond the point of resistance.
One press opens or closes the blind
completely.
After a new action on the the control, the
blind continues moving for around 2 cm,
then stops.
) Pull or press the control without goingbeyond the point of resistance (forwards to close and rear wards to open). When you release the control, the blindcontinues moving for around 2 cm, then stops.
Page 64 of 348
Safety anti-pinch
If the blind stops and immediately opens again
during a closing manoeuvre: ) operate the control until the blind is fully open, )
then operate the control until the blind is fully closed. The safety anti-pinch function is not operational during these operations.
If the blind meets an obstacle during operation, you must reverse the movement of the blind. To do this, press the control concerned. When the driver operates the blind control, they must ensure that no one ispreventing correct closing of the blind.
The driver must ensure that passengersuse the blind correctly.
Be aware of children when operating the blind.
Reinitialisation
If power to the blind is cut off while it is moving,
the safety anti-pinch must be reinitialised: )operate the control until the blind is fully closed, )continue to press for at least 3 seconds.
A slight movement of the blind will then be
noticeable, confirming the reinitialisation.
In automatic mode and at the end of its travel,
if the blind meets an obstacle while closin
g it stops and moves back slightly.
Page 77 of 348
75
Comfort
These have one position for use (up) and a
stowed position (down).
They can also be removed.
To remove a head restraint: ) release the backrest using control 1 , )
tilt the backrest 2slightly forwards, )
pull the head restraint upwards to the stop, )
then, press the lug A.
Rear head restraints
Never drive with the head restraintsremoved; they must be in place and correctly adjusted.
)Remove the seat cushion 1
from its fixings by pulling upwards.
Removing the seat cushion
Refittin
g the seat cushion
)Position the seat cushion 1
ver tically in itsfixings.
Page 79 of 348
77Comfort
Automatic day/night model
By means of a sensor, which measures the
light from the rear of the vehicle, this system
automatically and progressively changes
between the da
y and night uses.
Adjustable mirror providing a central rearwardview.
Equipped with an anti-dazzle system, whichdarkens the mirror glass: this reduces
the nuisance to the driver caused by the headlamps from following vehicles, low sun...
Rear view mirror
In order to ensure optimum visibility during your manoeuvres, the mirror lightens automatically when reverse gear is engaged.
Steering wheel adjustment
)When stationary, pull the control lever to yrelease the adjustment mechanism. )
Adjust the height and reach to suit your driving position. )
Push the control lever to lock theadjustment mechanism.
As a safety precaution, these operations should only be carried out while the vehicle is stationary.
As a safety measure, the mirrors shouldbe adjusted to reduce the "blind spot".
Seeing clearly
For better rear vision, align the bottom of the rear view mirror with the bottom of the rear screen.
