2012 Citroen DS3 lock

Familiarisation
90
Access
A.Unfolding/Folding the key.
B.Unlocking the vehicle.

Remote control key
1.Opening the fuel filler flap.
2. Opening and hooking the fuel filler cap.
Fuel t ank
102, 104
183
Ta n k c a p a c i ty:
- approximately 50 litres (petrol),
- approximately 46 litres (Diesel).
- (depending on version: approximately30 litres (petrol or Diesel)).
A.Interior release lever.B.
Exterior safety catch. C.
Bonnet stay.


Bonnet
Other functions...C.
Normal locking of the vehicle Vehicle location.

Instruments and controls
1.
Steering lock and ignition. 2.
Audio equipment steering wheel controls.3.
Wiper/screenwash/trip computer stalk.4.
Scented air freshener.5.
Central locking switch.
6.Multifunction screen.
7. Hazard warning lamp switch.8.Central adjustable air vents.9.
Sunshine sensor
Hi-Fi audio system central speaker. 10.Passenger's airbag. 11.
Side adjustable air vent. 12.Glove box/Passenger's airbag deactivation. 13.Parking brake.14.Central armrest with storage.15.
Upper and lower storage.16.
MyWay or Audio system. 17.Heating/air conditioning controls.

Sitting comfortably
)To raise it, pull it upwards. )To lower it, press simultaneously on the
tab A
and down on the head restraint.
Adjusting the height of
a head restraint
Other function available...
Heated seats.
80, 83
1.
Release the adjustment mechanism. 2.Adjust for height and reach.3.Lock the adjustment mechanism.


Steering wheel adjustment
85

For reasons of safety, these operationsmust only be carried out with the vehicle stationary.


Access to rear seats
)
Pull the control lever up to fold the backrestand move the seat forwards.

8
1
Take care to use only the correctcontrol, located at the top of the backrest.

35
Monitoring



Foot on thebrake pedal

fixed. The brake pedal must be pressed. With an electronic gearbox, press the brake pedal to start the engine (lever in position N). With an automatic gearbox, with the engine running,press the brake pedal before releasing the parking
brake, to unlock the lever and come out of position P.PIf you wish to release the parking brake without pressing the brake pedal, this warning lamp will
remain on.

flashing. With an electronic gearbox, if you hold the vehicle on an incline using
the accelerator for too long, the clutchoverheats. Use the brake pedal and
/or the parking brake.
Automatic wipingfixed. The wiper control is pushed downwards. Automatic front wiping is activated.




Passenger'sairbag systemfixed. The control switch, located in theglove box, is in the "ON" position. The passenger's front airbag is activated.
In this case, do not install a rear-
facin
g child seat.T
urn the control switch to the " OFF
" position
to deactivate the front passenger's airbag.
In this case you can install a rear-facing child seat.
Warning lampis onCauseAction/Observations

fixed, associated with
the STOP warninglamp. The brakin
g system fluid level is too low. You must stop as soon as it is safe to do so.
Top up with brake fluid recommended by CITROËN.
If the problem persists, have the system checked by
a CITROËN dealer or a qualified workshop.
+

fixed, associated with
the
STOP and ABSwarning lamp. Th
e electronic brake force distribution (EBFD) system has a fault. You must stop as soon as it is safe to do so.
Have it checked by a CITROËN dealer or a qualified
workshop.
Warning lampis onCauseAction/Observations
Anti-lock BrakingSystem (ABS) fixed. The anti-lock braking system has a fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact aCITROËN dealer or a qualified workshop without delay.
Dynamic stability control (ESP/ASR)
flashing. The ESP/ASR regulation is active. The system optimises traction and improves the
directional stability of the vehicle.

fix
ed. Unless it has been deactivated (button
pressed and its indicator lamp on) the
ESP/ASR system has a fault. Have it checked b
y a CITROËN dealer or a qualified
workshop.

A few seconds after the ignition is switched
on, the distance recorder resumes its normal
operation.
The spanner remainson.
The distance remaining may be weighted by the time factor, depending on the driver's driving habits.
Therefore, the spanner may also comeon if you have exceeded the two year service interval.
Service indicator zero reset

After each ser vice, the ser vice indicator mustbe reset to zero.
The procedure for resetting to zero is as
follows: ) switch off the ignition,)
press and hold the trip distance recorder
zero reset button,) switch on the ignition; the distance recorder
display begins a countdown,
) when the display indicates "=0", release
the button; the spanner disappears.
Following this operation, if you wish todisconnect the battery, lock the vehicleand wait at least five minutes for thezero reset to be taken into account.


Retrieving the service information

You can access the ser vice information at anytime. )Press the trip distance recorder zero reset button.
The ser vice information is displayed for afew seconds, then disappears.
Service overdue
For a few seconds after the ignition is switched on, the spanner flashes
to indicate that the
service must be carried out as soon as possible.Example:the service is overdueby 300 miles (km).
For a few seconds after the ignition is switched
on, the display indicates:

System which measures the total distance
travelled by the vehicle during its life.
The total and trip distances are displayed for
thirty seconds when the ignition is switched off,
when the driver's door is opened and when the
v
ehicle is locked or unlocked.
Total distance recorder
System which measures a distance travelled
during a day or other period since it was reset
to zero b
y the driver. ) With the ignition on, press the button until
zeros appear.



Tr ip distance recorder
System for manual adjustment of the brightness of the instruments and controls in relation to theexterior brightness.
Lighting dimmer


Activation

When the lighting is on:)press the button to change the brightness
of the instruments and controls,
)when the level of brightness required isreached, release the button.
Deactivation

When the lighting is off, or in day mode on
vehicles fitted with daytime running lamps,pressing the button does not have any effect.



To c o nform to legislation in the country you are crossing, change the units of distance (miles or km) via theconfiguration menu.

Removing the cartridge
)Press the dial and turn it a quar ter of a turnanti-clockwise.
)Remove the cartridge.)Refit its sealing case.

Fitting the cartridge
)
Remove the cartridge from the sealingcase.)
Install the car tridge (flower at top left).)
Press the dial and turn it a quar ter of a turn clockwise.