Page 140 of 216
138
V
A
SAFETY RECOMMENDATIONS
It is recommended that towbar installation and removal bedone by a CITROËN dealer or a qualifi ed workshop.
If you are towing another vehicle, the latter must be free-wheeling (gearbox in neutral).
Dimensions(in metres):
A:0.971
TOWBAR
(Boat, caravan, etc.)
It is recommended that towbar installation and removal be done
by a CITROËN dealer or a quali-fi ed workshop.
If you are climbing a steep gradient
and the engine gets excessively
hot, certain functions become una-
vailable (e.g. sequential control of
the automatic gearbox, the air con-
ditioning).
If you are towing, it is necesaary
to deactivate the parking assist-
ance by pressing the control on the
dashboard. See "Parking assist-ance".
It is recommended that
you remove
the towing ball, so that it does not
interfere with the functioning of the
proximity sensors, when you are
not using a trailer.
MAINTENANCE
if cleaning the vehicle with a highpressure system
Your Piloted Defl ector has to be closed.
It is not advisable to clean the
underside of the vehicle, for fear of damaging the electricparking brake.As water may penetrate into
the vehicle interior via the door
apertures, do not target these areas.
Do not direct at the headlamps,
lamps and their edges for too
long or you may damage their coating and seals.
ï
ï
ï
ï
Page 142 of 216
14 0
V
COLD WEATHER SHIELD
After fi tting Before fi tting
FITTING/REMOVAL OF THE
SNOW-GUARD
Fitting
Clip the snow-guard onto the ribs
of the bumper.
Removal
To detach the snow-guard, slide
the tool4 into the recesses in thesnow-guard and lift.Note:The tool 4 is to be found 4in the protection box in the sparewheel. See "Changing a wheel".
The snow-guard delivered with the vehicle (accordingto destination) should be fitted during the winter period,but removed for the remainder of the year.
It is essential to remove it whenever the temperature is above10 °C.
Page 143 of 216
141
V
4
3
8
9
61
2
5
7
CHANGING A WHEEL
ACCESS TO THE SPARE WHEEL
To access the spare wheel1.Lift the boot fl oor by means of the strap.2.Anchor the strap on the roof of the boot.3.To remove the spare wheel, detach the belt then push the wheelforwards so as to be able to lift it.
TO REPOSITION THE SPARE WHEEL
To put the spare wheel back in the boot1.Position the spare wheel fl at in the boot, then pull it towards you.2.Next place the toolbox inside the wheel, then secure the assembly with
the belt.3.Release the strap to return the boot fl oor to its initial position.
Tyre pressures
Tyre pressures are indicated on the label which is positioned low down on
the front pillar. See "Vehicle identifi cation" and "User Precautions". (On this label you will see a pressure for normal speeds and a pressure for high speeds).
1.Handle2.Jack3. Tool for removing/refi tting the
wheel bolts4. Tool for removing the anti-theft
bolt protector
5. Centring guide6. Tool for removing foglamps
and reversing lamps
7. Handle extension8. Towing eye9. Movable chock
TOOLS
The tools are to be found in a pro-
tective holder inside the spare
wheel. Pull back the retaining strap
t
o have access.
Page 144 of 216
142
V
Before positioning the jack, always adjust the vehicle's groundclearance to the "maximum height" position and retain thisadjustment for as long as the jack is under the vehicle (do notuse the hydraulic adjustments).
Never get underneath the vehicle if it is supported only by thejack.
The jack and all the tools are designed specifi cally for use on your particular vehicle. Do not use them for any other applications.
Have the original wheel repaired and refitted as soon aspossible.
It is imperative not to exceed a speed of 80 km/h (50 mph) onthe spare wheel.
REMOVAL1. Park the vehicle on stable, fi rm ground that is not slippery. Apply the
parking brake.2. It is essential to make sure that the occupants have left the vehicle and are in a place where their safety is guaranteed.3. With the engine idling, adjust the ground clearance to maximum height. See "Comfort" and "Ground clearance adjustment". Switch off the igni-
tion and engage fi rst gear or reverse gear depending on any slope (for a vehicle with automatic gearbox, select position P).4. Position the chock at the wheel that is diametrically opposite the one to
be replaced.
5. Position the jack at one of the four jacking-points provided on the sub-
frame close to the wheels, then use the handle to unwind the jack until
it reaches the ground.
6. Slide the removal tool4 into the notch and lever vigorously to detach
the anti-theft bolt protector. See illustration. You can use the handle at
the extremit
y of the tool 4.7.Slacken the wheel bolts.8. Continue to extend the jack until the wheel is a few centimetres off the ground.9. Undo the bolts, remove the wheel.
CHANGING A WHEEL
Page 145 of 216
143
V
It is imperative not to exceed a speed of 80 km/h (50 mph) onthe spare wheel.
The wheel bolts are specifi c to the type of wheel.
When replacing wheels, check with a CITROËN dealer or aqualifi ed workshop that the wheel bolts are compatible withthe new wheels.
Note: take care to note down the code number engraved on thehead of the anti-theft bolt socket. This will enable you to obtainreplacement anti-theft bolt sockets from a dealership.
WHEEL FOR TEMPORARY USE
If your vehicle is equipped with aspare wheel for temporary use
only, when fi tting it it is normal toobserve that the wheel bolts do notcome to bear on the wheel rim.
The spare wheel is secured by theconical tapering of the wheel bolt’sshaft. See illustration.
When refi tting the original wheel,ensure that the wheel bolt contactsurfaces are clean and in goodcondition.
REFITTING A WHEEL1. Fit the wheel on the hub,using the centring guide. Make sure that the contact surface between the hub and the wheel
is clean.2. Screw in the bolts but do not
fully tighten them.3. Lower the jack and remove it.4. Tighten the wheel bolts, usingthe wheelbrace.
5. Refi t the embellisher.
6. Return the ground clearance
to the normal position. See "Ground clearance adjustment".7.Ensure the tyre pressure
is correct (see "Vehicle
identifi cation") and have the balancing checked.
WHEEL EQUIPPED WITH DEFLATIONDETECTION SENSOR
Such wheels have tyre pressuresensors. Have it repaired by aCITROËN dealer or a qualifi edpy
workshop.
ANTI-THEFT BOLTS
Each wheel is equipped with oneanti-theft bolt.
To remove it1. Remove the protector that is covering it by means of the
tool 4 for "removing anti-theft protectors".2. Use the anti-theft socket with
the handle.
CHANGING A WHEEL
Page 146 of 216
144
V
TOWING WITH WHEELS ON THE GROUND
Towing eyes can be used at the front and at the rear of the vehicle.
Detach the cover:For the front cover, lever with a screwdriver at the top of the cover.
For the rear cover, press on the right hand side.
The ignition key must be in position M to retain steering.
Use a bar with attachments to the towing eyes as above.
The towing eye is removable, to be stowed in the jack protection box inside
the spare wheel.
•
•
ADVICE
Towingat low speed over a veryshort distanceis authorised inexceptional cases depending on
the regulations in force.
Otherwise, it is necessary to
have
your vehicle transportedon a recovery truck.
It is essential to check that theelectric parking brake is released.
REQUIREMENT - TOWING
WITH AUTOMATIC GEARBOX
Place the selector on position N(neutral).
When the engine is not running, the steering and the braking are no longer assisted.
If you are towing another vehicle, the latter must be free-wheeling (gearbox in neutral).
Towing with "front or rear lifted"or in the "minimum height"position is prohibited.
Page 177 of 216
7.27
1
22
33
55
66
44
06TELEPHONE
CALLING A CONTACT
Turn the dial and select the DIAL function.
Press the PICK UP button to displaythe telephone short-cut menu.
Press the dial to confi rm the selection.
Dial the telephone number of your contact using the alphanumeric keypad.
Press the PICK UP button to call the number dialled.
Press the HANG UP button to endthe call.
ACCEPTING OR REFUSING A CALL
Press the PICK UP button to accepta call.
Press the HANG UP button to refuse a call.
Press the end of the steering wheel stalk for more than 2 seconds to access the telephone menu: calls log, directory, voice mailbox.
To select the telephone used, press MENU, then select TELEMATICS, then BLUETOOTH FUNCTIONS, then BLUETOOTH ACT I VAT ION MODE. Then select:- DEACTIVATED: to use the internal telephone,- ACTIVATED AND VISIBLE: to use the bluetooth telephone, visible to all telephones,- ACTIVATED AND NOT VISIBLE: to use the bluetooth telephone, not visible to other telephones, it is not possible to match a new telephone.
Select CALL LIST or PHONE BOOK and press OK. Select the number required and confi rm to make the call.
DIAL
Page 181 of 216
7.31
08CONTROL SHORT-CUTS
STEERING WHEEL CONTROLS
RADIO: selection of the previous stored station.
MP3/JUKEBOX: selection of the previous directory.
Selection of the previous item on a menu.
RADIO: selection of the next stored station.
MP3/JUKEBOX: selection of the next directory. Selection of the next item on a menu.
RADIO: automatic search for a higher frequency. CD/MP3/JUKEBOX: selection of the next track.
CD: continuous press: fast forwards play.
RADIO: automatic search for a lower frequency.CD/MP3/JUKEBOX: selection of the previous track. CD: continuous press: fast backwards play.
- Change of sound source. - Confi rmation of a selection. - Pick up/Hang up the telephone.- Press for more than 2 seconds:access to the telephone menu.
Volume increase.
Volume decrease.
Mute: by pressing the volumeincrease and decreasebuttons simultaneously.
The sound is restored by pressing one of the two volume buttons.
