Page 85 of 340
IV
83
ACCESS
Cancelling the memorisation
With the tailgate in the intermediate
position, you can cancel the stored
position:
)
Make a long press on push-
button D
. The system emits a
long audible beep.
)
Release the push-button D
. The
tailgate will return to the fully
open position at the next use.
Electrical protection of
the motor
If the tailgate is repeatedly opened
and closed in quick succession, the
motor can start to overheat and then
cut out, preventing opening and
closing of the tailgate.
Allow the motor to cool down for
ten minutes without opening or clos-ing the tailgate.
Closing in manual back-up mode re-
mains possible.
To avoid risk of injury, make sure
that no one is in the vicinity of the
boot while opening and closing.
If the tailgate is carrying extra
weight (snow, bicycle carrier, etc.)
there is a risk of it closing under
this load. Support the tailgate or
fi rst unload the bicycle carrier or
clear the snow.
When using an automatic car wash, don’t forget to lock the vehicle so
as to avoid any risk of motorised
opening of the tailgate.
Page 102 of 340
VI
!
100
FITTINGS
SUN VISOR
SKI FLAP
A fl ap in the backrest, located to the
rear of the armrest, facilitates the
carrying of long objects.
)
With the ignition on, lift the fl ap; the
mirror is illuminated automatically.
To prevent dazzle from ahead, fold
the visor downwards.
It can be disengaged from its central
fi xing and pivoted over to the side
windows if required.
Cooled glove box
)
To open the glove box, pull on
the handle and lower the lid.
The glove box has a manually clos-
able air vent B
.
It has 2 or 3 sockets C
to connect
audio/video equipment and a hold-
er for a SIM card (see "Audio and
Telematics").
It has automatic illumination.
It provides access to the dashboard
fusebox.
To open
)
Lower the rear armrest.
)
Pull the fl ap handle down.
)
Lower the fl ap.
)
Load the objects from inside the
boot.
Ensure that the objects are well se-
cured and that they do not impede
the operation of the gear lever.
The glove box should be
kept closed while driving.
Page 105 of 340
VI
103
FITTINGS
BOOT FITTINGS (SALOON)
1.
Battery location for vehicles with
V6 HDi engine.
2.
Boot fl oor (spare wheel storage).
3.
Boot lamp.
4.
Location for 6 CD changer.
Luggage securing rings
)
Use the 4 securing rings on the
boot fl oor to secure your lug-
gage.
For safety reasons in the event of
sharp braking, you are advised to
place heavy objects as far forward
in the boot as possible.
Page 106 of 340
VI
104
FITTINGS
BOOT FITTINGS (TOURER)
1.
Hook
For shopping bags.
2.
Torch
To recharge, return it to its storage
position.
3.
Storage net
or Battery compart-
ment (for vehicles with 3 litre
V6 HDi engine).
This provides access to the battery.
1.
Luggage-cover blind
(see details on following page)
2.
Luggage securing rings
Use the 4 stowing rings provided
on the boot fl oor to secure your
loads.
For safety reasons in the event
of sharp braking, you are ad-
vised to place heavy objects as
far forwards as possible.
3.
Hooks
These allow a cargo net to be
fi tted (see details on following
page).
1.
Boot lamp
2.
12 V accessories socket
(100 W maximum)
Cigarette lighter type 12 volt
socket. It is located on the rear
right-hand trim.
3.
Loading height control
You can change the height of the
vehicle to make loading or un-
loading easier.
4.
Hook
For shopping bags.
5.
Storage net
or closed housing
Location for the 6 CD changer.
Page 107 of 340
VI
105
FITTINGS
LUGGAGE COVER (TOURER)
To roll up
)
Press the handle (PRESS) gently.
The luggage cover rolls up auto-
matically.
The moving part A
can be folded
along the rear bench seat backrest.
To remove
)
Compress the control 1
and lift
the luggage cover on the right
then on the left to remove it.
To install
)
Position the left-hand end of the
luggage cover roller in its loca-
tion B
behind the rear bench
seat.
)
Compress the roller control 1
and put the roller in place in its
location C
on the right.
)
Release the control to secure
the luggage cover.
)
Unroll it to its fastening on the
rear pillar.
High load retaining net
(Tourer)
Hooked onto the special upper and
lower fi xings, this permits use of the
entire loading volume up to the roof:
- behind the rear seats (row 2),
- behind the front seats (row 1)
when the rear seats are folded.
When positioning the net, check that
the strap loops are visible from the
boot; this will make slackening or
tightening easier.
Page 113 of 340
VII
111
CHILD SAFETY
"ISOFIX" MOUNTINGS
Your vehicle has been approved in
accordance with the new ISOFIX
regulation
s
.
The outer rear seats are fi tted with
regulation ISOFIX mountings.
In the rear
This ISOFIX mounting system pro-
vides fast, reliable and safe fi tting
of the child seat in your vehicle.
The ISOFIX child seats
are fi tted
with two locks which are secured
easily on the two rings A
, following
installation of the guides (supplied
with the seat).
Some also have an upper strap
which is attached to the ring B
or C
.
To attach this strap in the rear, remove
the vehicle seat's head restraint and
stow it. Lift the cover on the rear shelf
(Saloon) or the roof (Tourer). Then
fi x the hook on the ring B
or C
and
tighten the upper strap.
The incorrect installation of a child
seat in a vehicle compromises the
child's protection in the event of an
accident.
For information regarding the
ISOFIX child seats which can be
installed in your vehicle, consult
the table of positions for fi tting
ISOFIX child seats.
Saloon
These are three rings for each outer
rear seat:
- two lower rings A
, located be-
tween the vehicle seat back and
cushion, indicated by a label,
- an upper ring B
, fi xed to the rear
shelf, concealed under a fl ap
with the logo TOP TETHER be-
hind the head restraint.
Tourer
- two lower rings A
, located be-
tween the vehicle seat back and
cushion, indicated by a label,
- an upper ring C
, fi xed to the
roof on the boot side, concealed
under a fl ap with the logo TOP
TETHER.
Page 178 of 340
XI
176
PRACTICAL INFORMATION
TEMPORARY PUNCTURE
REPAIR KIT
Using the kit
The kit is located in the boot under
the fl oor.
)
Switch off the ignition.
)
Affi x the speed limitation sticker
to the vehicle's steering wheel
to remind you that a wheel is in
temporary use.
)
Check that the switch A
is in
position "0"
.
)
Connect the pipe of the car-
tridge 1
to the valve of the tyre to
be repaired.
)
Connect the compressor's elec-
tric plug to the vehicle's 12 V
socket.
)
Start the vehicle and leave the
engine running. Complete system consisting of a
compressor and a sealant cartridge
which permits the temporary repair
of the tyre so that you can drive to
the nearest garage.
This repair kit is available from
CITROËN dealers or a qualifi ed
workshop.
It is designed to repair holes of a
maximum diameter of 6 mm, locat-
ed exclusively on the tyre tread or
shoulder. Avoid removing any for-
eign bodies which have penetrated
the tyre.
Page 182 of 340
XI
!
180
PRACTICAL INFORMATION
Access to the spare wheel
To remove the spare wheel
)
Lift up the boot fl oor and fold in
two (Saloon) or hook it using the
retractable handle (Tourer).
)
Detach the strap then push the
wheel forwards so as to be able
to lift it.
To reposition the spare wheel
)
Position the spare wheel fl at in
the boot, then pull it towards
you.
)
Next place the toolbox inside the
wheel, then secure the assembly
with the strap.
)
Release the boot fl oor to return it
to its initial position.
The tyre pressures are indi-
cated on the label located on
the driver's side centre door
pillar. Tyre pressures are given for
different vehicle loading conditions.
