Page 165 of 352
IX
163
DRIVING
Deactivation
Press on button 3
.
This action causes the
information "OFF"
to
appear on the instru-
ment panel screen.
This action does not cancel the
memorised maximum speed which
remains displayed in zone A
of the
instrument panel.
Override of the programmed
speed
The accelerator pedal is equipped
with an end-of-travel switch. If you
action this switch by pressing the
pedal hard down, you can exceed
the memorised maximum speed at
any time.
During the time the speed is be-
ing exceeded, the displayed speed
fl ashes.
You have only to release the ac-
celerator pedal to return below the
maximum speed and render the
function active again.
Return to normal driving
)
By moving the control 1
from po-
sition "LIM"
to position 0
.
)
By the engine stopping.
The speed previously chosen is still
memorised.
Operating fault
If there is a speed limiter malfunc-
tion, a message will display accom-
panied by an audible signal and
lighting of the service warning lamp.
Have it checked by a CITROËN
dealer or a qualifi ed workshop. If during the operation of the speed
limiter, the system is unable to keep
within the maximum speed (for ex-
ample on a steep descent or under
heavy acceleration) then the speed
fl ashes. Adapt your speed as neces-
sary.
The function will re-engage when
your speed returns below the de-
sired maximum speed.
On a steep downhill gradi-
ent or on sharp accelera-
tion, the speed limiter will
not be able to prevent the vehicle
from exceeding the programmed
speed.
Use of fl oor mats that are not ap-
proved by CITROËN may hinder
access to the accelerator pedal
and thus interfere with the function-
ing of the speed limiter.
To avoid any risk of interfering with
the pedals:
- check that the fl oor mat is cor-
rectly positioned,
- never use more than one fl oor
mat.
Page 167 of 352
IX
165
DRIVING
Reactivation
)
By recall of the memorised
speed
After a disengagement, press on
button 3
. Your vehicle automati-
cally returns to the memorised
cruise speed which is displayed
in zone A
.
If the memorised cruise speed
is higher than the current speed,
the vehicle will accelerate to
reach the former.
)
By selection of the current
speed
Press on button 2
or 4
once the
desired speed has been reached.
The information "OFF"
will then
disappear from the instrument
panel display.
Overriding the programmed
speed
During the operation of cruise con-
trol, it is always possible to use the
accelerator to go faster than the
cruise speed (for example to over-
take another vehicle). The speed
displayed in zone A
fl ashes.
You have only to release the accel-
erator pedal to return to the cruise
speed. If during the operation of cruise
control, the system is unable to
keep within the memorised speed
(for example on a steep descent),
then the speed fl ashes. Adapt your
speed as necessary.
Return to normal driving
Operating fault
If there is a malfunction, a message
will display accompanied by an audi-
ble signal and lighting of the service
warning lamp.
Have it it checked by a CITROËN
dealer or a qualifi ed workshop.
Cruise control should only
be used when the driving
conditions allow you to drive
at a constant speed.
Do not use it in heavy traffi c, or on
dangerous or slippery roads.
The driver must remain attentive
and in full control of his vehicle.
You are recommended to always
keep your feet within range of the
pedals.
To avoid any risk of interfering with
the pedals:
- check that the fl oor mat is cor-
rectly positioned,
- never use more than one fl oor
mat.
)
By an action on the control 1
from
position "REG"
to position 0
.
)
By the engine stopping.
The cruise speed previously
chosen is no longer memorised.
Page 174 of 352
IX
172
DRIVING
Loading/unloading
assistance
Grand
C4 Picasso
C4 Picasso
The pneumatic suspension has an
additional function: the possibility to
raise or lower the height of the rear
of the vehicle when stationary, in or-
der to facilitate loading/unloading of
the boot.
Increasing the height of the boot
fl oor
)
Press continuously the top con-
trol A
, which is located in the
boot, on the left-hand side.
This action will be accompanied by
an audible signal. You can stop the
movement at any time by releasing
the control.
3 beeps will confi rm that the move-
ment has gone as far as it can.
Returning to the normal height
)
Press briefl y the bottom of con-
trol A
twice.
Decreasing the height of the boot
fl oor
)
Press continuously the bottom of
control A
.
This action will be accompanied by
an audible signal. You can stop the
movement at any time by releasing
the control.
3 beeps will confi rm that the move-
ment has gone as far as it can.
Returning to the normal height
)
Press briefl y the top of control A
twice.
Driving with the boot in a
low position may damage
underbody components.
Particular points
- If you start the vehicle without
having returned it to the normal
height, automatic correction will
activate as soon as the vehicle
starts to move. During the cor-
rection, the service warning
lamp comes on and a message
on the screen reminds you not to
exceed 6 mph (10 km/h).
- Loading assistance does not
function in the following circum-
stances:
- If button B
is illuminated,
- in power economy mode,
- when you fi
rst use the function,
press control A
for two seconds
to initialise the system. The sys-
tem will respond normally to sub-
sequent operation of the control.
Page 182 of 352
X
180
CHECKS
Screenwash and headlamp wash
fl uid
Fluid specifi cation
For optimum cleaning and to avoid
freezing, this fl uid must not be
topped up with or replaced with plain
water.
Diesel additive level (Diesel
engine with particle emission
filter)
A low additive level is indicated by
illumination of the service warning
lamp, accompanied by an audible
warning and a message in the multi-
function screen.
Topping up
This additive must be topped up by
a CITROËN dealer or a qualifi ed
workshop without delay.
Used products
Avoid prolonged contact of
used oil or fl uids with the
skin.
Most of these fl uids are harmful to
health or indeed very corrosive.
Do not discard used oil or
fl uids into sewers or onto
the ground.
Take used oil to a CITROËN dealer
or a qualifi ed workshop (France) or
to an authorised waste disposal
site.
In the case of vehicles fi tted
with headlamp washers, the
low fl uid level is indicated
by an audible signal and a
message in the screen.
Top up the reservoir when you next
stop the vehicle.
Coolant level
Changing the coolant
The coolant does not have to be
changed.
Fluid specifi cation
The coolant must conform to the
manufacturer’s recommendations.
The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm,
the temperature of the coolant is
regulated by the fan. This can ope-
rate with the ignition off.
On vehicles which are fi tted with
a particle emission fi lter, the fan
may operate after the vehicle has
been switched off, even if the
engine is cold.
In addition, as the cooling system is
pressurised, wait at least one hour
after switching off the engine before
carrying out any work.
To avoid any risk of scalding, un-
screw the cap by two turns to al-
low the pressure to drop. When the
pressure has dropped, remove the
cap and top up the level.