2012 Citroen C ZERO RHD turn signal

.Familiarisation
15
Driving safely
P.
Parking.
Press the brake pedal to come out of this
position. R.Reverse. N. Neutral. D.Drive (forward).


Drive selector
55- Check that the drive selector is in position
P.P- Inser t the key in the ignition switch.
- Turn the key to position 4 (START).- Hold it in this position for a few seconds,until the " READY" lamp comes on,
accompanied by an audible signal.
- Release the key.
The switch returns automatically to
position
3 (ON) .
Starting the motor
53



- Stop the vehicle.

- Keep your foot on the brake pedal.

- Put the drive selector in position P
. P

- Apply the parking brake.

- Turn the key anti-clockwise to the LOCKposition.


Stopping the motor
53

Monitoring
20
Operation indicator lamps
If one of the following indicator lamps comes on in the instrument panel, this confirms that the corresponding system has come into operation.

Warning / indicator lampStateCauseAction / Observations



Left-hand direction indicator
Flashing with audible signal. The lighting stalk is pushed down.


Right-hand direction indicator
Flashing with audible signal. The lighting stalk is pushed up.


Hazard warning lampsFlashing with audible signal. The hazard warning lamps switch,located on the dashboard, has been
operated. The left-hand and ri
ght-hand direction indicators and
their associated indicator lamps flash simultaneously.


Sidelampsand/or dipped beamheadlamps
On fixed. The sidelamps and/or dipped beamheadlamps are on.



Front foglampsOn fixed. The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off
the front foglamps.


Rear foglampOn fixed. The rear foglamp is switched on. Turn the ring on the stalk rear wards to switch off the
rear foglamp.


Main beam headlampsOn fixed. The lighting stalk is pulled towardsyou. Pull the stalk to return to dipped beam headlamps.

4
Driving
53








Starting - stopping the vehicle



- Position 1: LOCK
The steering is locked.

- Position 2: ACC The ancillaries (radio, 12 V socket...) canbe used.

- Position 3: ON Ignition on.

- Position 4: START "Ready" lamp on.
Motor ready to drive the vehicle.
Ignition switch
)
Inser t the key in the ignition switch.
)
Turn the key to position 4 (START).
Starting
Stopping
)
Immobilise the vehicle.
)
Place the drive selector in position P.P)
Turn the key to position 1 (LOCK).)
Remove the key from the ignition switch. )Hold it in this position for a few seconds until the " READY"
lampcomes on accompanied by anaudible signal.
)
Release the key.
The key returns automatically to
position 3 (ON).

Do not attach any heavy objects to thekey as this could weigh down on it whenin the ignition switch and cause a fault.


If you use the ancillaries for a prolonged period (with the key in the ACC
position), you risk discharging the ancillaries battery. Star ting your vehicle will then no longer be possible.Be aware .

Visibility
58
Foglamps selection ring.
The foglamps operate with the sidelamps and
dipped and main beam headlamps.Front and rear
foglamps .In good or rainy weather, both day and night, the front foglamps and the rear foglamp is prohibited. In thesesituations, the power of its beam may
dazzle other drivers.
Do not forget to switch off the front foglamps and the rear foglamp whenthey are no longer necessary.


Lighting on reminder
There is an audible signal when thedriver's door is opened, to warn thedriver if the vehicle lighting is on, withthe ignition off. Switching off the lighting stops theaudible signal.
)
To switch on the front foglamps, turn the
ring for wards once. ) To switch on the rear foglamp, turn the ringforwards twice. )
To switch off the rear foglamp, turn the ring
rearwards twice. ) To switch off the front foglamps, turn the
ring rearwards once.
The ring returns to its initial position
automaticall
y.
The rear foglamp is switched off automatically
when you switch off the sidelamps, or the
dipped or main beam headlamps.

7
Safety
75
Seat belts


Front seat belts
Fastening
)
Pull the strap, then inser t the tongue in thebuckle A.)
Check that the seat belt is fastened correctly by pulling the strap.



Front seat belt not fastened /
unfastened warning lamp

If the driver does not fasten their seat belt
within one minute after switching on the
ignition, the warning lamp flashes accompanied
by an intermittent audible signal.
After about 90 seconds, the warning lamp, the
audible signal and the display stop, and then
return until the driver fastens their seat belt.
If the seat belt is unfastened while the vehicle is moving
, you are warned by the same alerts.

Th
e front seat belts are fitted with a
pretensioning and force limiting system.
This system improves safety in the frontseats in the event of a front or side impact.
Depending on the severity of the impact,
the pretensioning system instantly tightens the seat belts against the body of the occupants.
The pretensioning seat belts are active when
the ignition is on.
The force limiter reduces the pressure of the seat belt on the chest of the occupant,so improving their protection.

Unfastening
)
Press the red button on the buckle A
.
When the i
gnition is switched on, this
warning lamp comes on accompanied
by an audible signal for a few seconds
if the driver and/or passenger has notfastened their seat belt.