2012 CITROEN C-ELYSÉE display

86
Driving
) Turn thumb wheel 1to the "LIMIT"position: the speed limiter mode
is selected but is not switched on(PAUSE).
You do not have to switch the speed limiter
on in order to set the speed.
Programming
Leaving limiter mode
)Turn thumb wheel 1
to the "0"position:
the speed limiter mode is deselected. The
displa
y returns to the distance recorder.
On a steep descent or in the event of sharp acceleration, the speed limiter willnot be able to prevent the vehicle from exceeding the programmed speed.
To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- do not fit one mat on top of another.

In the event of a speed limiter fault, the speed
is cleared resultin
g in flashing of the dashes.
Have it checked by a CITROËN dealer or a qualified workshop.


Operating fault
)Set the speed value by pressing button 2or 3(e.g.: 55 mph (90 km/h)).
You can then change the programmed speed using buttons 2 and 3
:
- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed speed will not haveany effect unless you press the pedal firmlypast the ypoint of resistance.The speed limiter is deactivated temporarily and the programmedspeed, which is still displayed, flashes.Returning to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of the
programmed speed.
)Switch the speed limiter back on by pressing button 4 again.

)Switch the speed limiter on by pressing button 4 . )Switch the speed limiter off by pressing button 4: the display confirms that it has been switched off (PAUS E).

87
5
Driving





Cruise control
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.

The cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph (40 km/h), as well as the engagement of:


-
fourth gear on a manual gearbox,

- second gear on a or automatic or electronic gearbox, in sequential mode,

- position A
on an electronic gearbox or position D
on an automatic gearbox.
Th
e cruise control is switched off
manually for by pressing the brake or clutch pedal or
on triggering of the ESP system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal.
Switching off the ignition cancels any programmed speed value. The controls o
f this system are grouped
together on stalk A.
1.Cruise control mode selection thumb wheel.
2. Value decrease button.3.
Value increase button.4.
Cruise control off/resume button.

Steering mounted controls
The cruise control cannot, in any circumstances, replace the need to respect speed limits, nor can it replace the need for vigilance and responsibilityon the par t of the driver. The pro
grammed information is grouped
together in the instrument panel screen.
5. Cruise control off/resume indication.
6. Cruise control mode selection indication. 7. Programmed speed value.


Displays in the instrument panel

88
Driving
) Turn thumb wheel 1to the "CRUISE"position: the cruise control mode
i
s selected but is not switched on(PAUSE).
Programming
You can then change the programmed speed using buttons 2 and 3:- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.

When the cruise control is switched on, be careful if you maintain the pressure on one of the programmed speed changing buttons: this may result in a very rapid change in the speed of your vehicle.
Do not use the cruise control on slippery roads or in heavy traffic. On a steep descent, the cruise control will not be able to prevent the vehiclefrom exceeding the programmed speed.
To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- never fit one mat on top of another.

In the event o
f a cruise control malfunction,
the speed is cleared resulting in flashing of the
dashes. Have it checked by a CITROËN dealer
or a qualified workshop.

Operating fault
Leavin
g cruise control mode
)Turn thumb wheel 1 to the "0"position: the cruise control mode isdeselected. The display returns to the distance recorder.

Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results
in flashing of this speed in the screen.
Return to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of the speed.
)Set the programmed speed byaccelerating to the required speed,
then press button 2 or 3
(e.g.: 70 mph(11 0 k m / h)).
)Switch off the cruise control by pressing button 4
: the screenconfirms that it has been switched off (PAUSE).
)Switch the cruise control back on by pressing button 4again.

89
5
Driving
obstacle (person, vehicle, tree, gate, etc.) which comes within the field of detection of sensorslocated in the bumper.
Cer tain types of obstacle (stake, roadworkscone, etc.) detected initially will no longer bedetected at the end of the manoeuvre due to
the presence of blind spots.






Rear parking sensors


This function cannot, in any circumstances, take the place of the vigilance and responsibility of the driver.
The system is switched on by engaging reverse
gear. This is accompanied by an audible signal.
The s
ystem is switched off when you come out
of reverse
gear.
Audible assistance
The proximity information is given by anintermittent audible signal, the frequency of which increases as the vehicle approaches the obstacle.
The sound emitted by the speaker (right or left)indicates the side on which the obstacle is located.
When the distance between the vehicle andthe obstacle becomes less than approximately
thirty centimetres, the audible signal becomescontinuous.



Visual assistance
This supplements the audible signal bydisplaying bars in the multifunction screen
which move progressively nearer to the vehicle.
When the obstacle is near, the "Danger" symbol is also displayed in the screen.

90
Driving
In bad weather or in winter, ensure that the sensors are not covered with mud, ice or snow. When reverse gear isengaged, an audible signal (long beep)indicates that the sensors may be dirty.
Cer tain sound sources (motorcycle,lorry, pneumatic drill, etc.) may trigger the audible signals of the parking
sensor system.
In th
e event of a malfunction of
the system, when reverse gea
r
is engaged this warning lamp
is displayed in the instrument panel and/or a message appears in the screen, accompanied
by an audible signal (short beep).
Contact a CITROËN dealer or a qualified
wor
kshop.

Operating fault
The function will be deactivated automatically if a trailer is being towed or a bicycle carrier is fitted (vehicle fitted with a towbar or bicycle carrier recommended by CITROËN).

Deactivation / Activation of the
rear parking sensors
The function is deactivated or
activated via the vehicle con
figuration menu.
The status of the function is stored
when the ignition is switched off.
For more in
formation on access to the parkingsensors menu, refer to the "Personalisation -Configuration" par t of the "Instruments andcontrols" section.

92
Visibility
Selection ring for main lighting mode
Turn the ring to position the symbol required
facing the mark.
Li
ghting off.

Sidelamps only.
Dipped or main beam headlamps.

Dipping the headlamps

Pull the stalk to switch the lighting between
dipped / main beam headlamps.

In the li
ghting off and sidelamps modes, the driver can switch on the main beam headlamps
temporaril
y ("headlamp flash") by maintaining apull on the stalk.


Displays

Illumination of the corresponding indicator lamp
in the instrument panel confirms the lightingswitched on.

176
01

On / Off.
FIRST STEPS


Volume adjustment.

Select screen displaybetween modes:
Full screen: Audio
(or
telephone if call in progress) /
In a window: Audio
(or
telephone if call in progress) -
Time or Trip computer.
Lon
g press: black screen(DARK).

Selection of AM / FM
wavebands.
Select preset radio station. Long press: store a station.

Displa
y the list of stations received, CD/MP3 tracks or folders.
Lon
g press: managing the classifi cation of MP3/WMA fi les / update the list of stations received.
TA
(Traffi c Announcement)
function On / Off.
Lon
g press: access to typeof information.
Confi rmation
or display of contextual menu.
Automatic search up
/ downfor radio frequencies.
Select previous / next CD, USB, streaming track.
Navi
gation in a list.

Abandon the current operation.
Up one level (menu or folder). Manual step b
y step search up / down for radio frequencies.
Select previous / next MP3 folder.
Select previous / next folder / genre / artist /
playlist in the USB device.
Navi
gation in a list.
Select source:
Radio, CD, AUX, USB,Streaming.
Accept an incomin
g call.

A
ccess to main menu.

Audio settings:
audio ambiences, treble, bass,
loudness, distribution, left/ri
ght
balance, front/rear fader,
automatic volume.

178
03 MAIN MENU


" Multimedia
": Mediaparameters, Radioparameters.
> SCREEN C
"
Trip computer":rWarning log. "Telephone ": Call, Directory
management, Telephone
management, Hang up.
" Personalisation-confi guration":Defi ne the vehicle parameters, Choice of
language, Display confi guration, Choiceof units, Date and time adjustment.

For a detailed
global view of the menus
available, refer to "Screen menu map" section.

"
Bluetooth connection":Connections management,Search for a device.