2012 CITROEN C-ELYSÉE brake

78
Driving

Gear lever















Electronic gearbox


Displays in the instrument panel


Gear lever positions
N.NeutralR.Reverse
1 2 3 4 5.Gears in manual mode.
AUTO. This comes on when automated mode
is selected. It goes off when changing to
manual mode.
R. Reverse ) With your foot on the brake, move the lever for wards to select this position.N.Neutral. )
With your foot on the brake, select this
position to start the engine.
A . Automated mode.) Move the lever backwards to select this
mode. M + / -.Manual mode with sequential gear changing.)
Move the lever backwards, then to the left
to select this mode, then:


- push for wards to change up a gear,

- or push backwards to change down a gear.
Five-speed electronicall
y controlled gearbox
which offers a choice between the comfort of automated operation or the pleasure of manualgear changing.
Tw o d r i v i ng modes are offered: -automatedmode for automatic control
of the gears by the gearbox, without anyaction by the driver,- manualmode for the sequential changingof the gears by the driver, using the gear lever.
)Place your foot on the brakewhen this warning lamp flashes (e.g.: star ting the engine).

79
5
Driving
N
appears in the instrument panel.
N
flashes in the instrument panel screen if the gear lever is not in position Nwhen starting.


You must keep your foot on the brakepedal while star ting the engine.
The vehicle then moves off on itsown (refer to the paragraph "Creepfunction").
)
Select automated mode (position A
), A
manual mode (position M ) or reverse (position R
) R
AUTO
and 1
, 1
or R
appear in the
instrument panel.
) Release the parking brake.)
Progressively take your foot off the brake
pedal.

Moving off
)Select position N.
)Press the brake pedal fully.)Star t the engine.
Do not press the brake and clutch pedals simultaneously. This can cause rapid clutch wear.


The creep function may be temporarilyunavailable if the clutch temperature istoo high or the slope too steep.



Do not leave children unsuper visedinside the vehicle when the engine is running.
)
Accelerate away.


Creep function

This function allows the vehicle to be
manoeuvred more easily at low speeds (when
parking, in traffic jams...).
With the gear lever in position A, Mor R, the
vehicle moves as soon as you take your foot off the brake pedal, at low speed andwith the engine at idle.

80
Driving
Automated mode
AUTOand the gear engaged appear in the instrument panel.

Manual mode
The gears engaged appear insuccession in the instrument panel.
The
gearbox then operates in auto-adaptive mode, without any action on the par t of thedriver. It continuously selects the most suitable gear taking account of:
- optimisation of fuel consumption,
- driving style,
- road conditions,
- v
ehicle load.
For optimum acceleration, when over takinganother vehicle for example, press theaccelerator pedal fully down, beyond the point of resistance. The
gear change requests are only carried out
i
f the engine speed permits.
It is not necessary to release the accelerator
pedal during gear changes.
When braking or slowing down, the gearbox changes down automatically so that the vehicle
picks up in the right gear.
Under full acceleration, the change up will not
take place unless the driver operates the gear lever (unless the engine is close to its maximum
speed).

Never select neutral (position N ) when moving.



You can change mode at any time bymoving the gear lever from Ato Mor the other way round.
Never select neutral (position N) whenmoving.
You can change mode at any time by moving the gear lever from A
to M
or the other way round.
)Select position A.)
Select position M.


Reverse
To engage reverse, the vehicle must be
immobilised with
your foot on the brake.)Select position R.

At low speed, if reverse gear is requested, the Nwarning lamp flashes and the gearbox goes
into neutral automatically.
To e n
gage reverse, put the gear lever intoposition N, then to position R
.


There is an audible signal onengagement of reverse.

81
5
Driving
AUTO
and -
appear in the instrumentpanel.
)
Select position N.)
Press the brake pedal. )
Wait for around 30 seconds until N
or agear appears in the instrument panel.)
Move the gear lever to position A
, then to
position N.) With your foot still on the brake pedal, start
the engine.The gearbox is operational again.
Reinitialisation
Following disconnection of the battery, it is
necessary to reinitialise the gearbox.) Switch on the ignition.


Before doing anything under the bonnet, ensure that the gear lever is inneutral (position N ) and that the parkingbrake is applied.



In exceptional circumstances, the gearbox may need an automatic reinitialisation: starting and gear changing are no longer possible.
AUTOand -appear in the instrument panel.

For all parking situations, you mustapply the parking braketo immobilise the vehicle.

When immobilising the vehicle with theengine running, you must put the gear lever into neutral (position N)
. Be
fore switching off the engine:


- chan
ge to position N
to be in neutral,
or

- leave the vehicle in gear; in this case the
vehicle cannot be moved.

Follow the procedure described above.



Stopping the vehicle

With the ignition on, if this warninglamp comes on and AUTOflashes, accompanied by an audible signal and
a message in the multifunction screen, this
indicates a gearbox fault. Have it checked by a CITROËN dealer or a qualified workshop.


Operating fault

82
Driving
Four-speed automatic gearbox which offers a choice between the comfor t of fully automatic operation, enhanced by spor t and snow
programmes, or manual gear changing.
There are therefore four driving modes:-automatic
operation for electronic management of the gears by the gearbox,
-
sportprogramme for a more dynamic style
of driving,

- snowprogramme to improve driving when
traction is poor,

-
sequentialoperation for manual changing
of the gears by the driver.















Automatic gearbox
1.
Gear lever.2.
Button "S"(sport)
.
3.Button "7"(snow).
Gear selection gateGear lever
P. Park.
- Immobilisation of the vehicle, parking brakeon or off.
- Starting the engine. R.Reverse.
- Reversing manoeuvres, vehicle stationary, engine at idle.N.
Neutral.
- Immobilisation of the vehicle, parking brakeon.
- Star ting the engine. D.
Automatic operation.M + / -. Manual operation with sequentialchanging of the four gears. )Push for wards to change up through the
gears.or )Pull backwards to change down throughthe gears.



Displays in the instrument panel

When you move the lever in the gate to select
a position, the corresponding indicator is
displayed in the instrument panel. P.ParkR. Reverse N. NeutralD. Drive (Automatic driving)
S.Sportprogramme7
.
Snow
programme1 2 3 4
.
Gears engaged during manual
operation
-.Invalid value during manual operation

Foot on brake
)
Press the brake pedal when this
indicator lamp is displayed in the
instrument panel (e.g.: star tingthe engine).

83
5
Driving
Apply the parking brake. )Select position P or N
.
)Star t the engine.
If this procedure is not followed, there is an
audible si
gnal, accompanied by the display of
an warning message.)With the engine running, press the brake pedal. )Release the parking brake. )Select position R, Dor M.)Gradually release the brake pedal.
The vehicle moves off immediately.


Moving off


When the engine is running at idle, with the brakes released, if position R, D
or M
is selected, the vehicle moves evenwithout the accelerator being pressed.
When the engine is running, never leave children in the vehicle without supervision. When carrying out maintenance with the engine running, apply the parkingbrake and select position P
.
P


If position N
is selected inadver tently while driving, allow the engine toreturn to idle then select position D
toaccelerate.
Never select position N
while the vehicle is moving.Never select positions P
or Runless thevehicle is completely stationary.

Automatic operation
)
Select position Dfor automaticchanging
of the four gears.The gearbox then operates in auto-adaptivemode, without any inter vention on the par t
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
v
ehicle.
For maximum acceleration without touching the gear lever, press the accelerator pedal downfully (kick down). The gearbox changes downautomatically or maintains the gear selecteduntil the maximum engine speed is reached.On braking, the gearbox changes downautomatically to provide efficient engine
braking.
If you release the accelerator sharply, thegearbox will not change to a higher gear for
safety reasons.

Sport and snow programmes


Sport programme "S"
)
Press button "S", after star ting the engine.
The
gearbox automatically favours a dynamic style of driving.
S
appears in the instrument panel.


Snow programme " 7
"
)
Press button "7
", after star ting the engine.
The gearbox adapts to driving on slipperyroads.
This programme improves star ting and drive
when traction is poor.
7 appears in the instrument panel.


Return to automatic
o
peration
) At any time, press the button selectedagain to quit the programme engaged and
return to auto-adaptive mode. These two special programmes supplement the
automatic operation in ver
y specific conditions of use.

84
Driving
Manual operation
)Select position M for sequentialchanging
o
f the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the
instrument panel.

Invalid value during manual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage
position Por N
to place the gearbox in neutral.
In both cases, apply the parking brake to
immobilise the vehicle.

Operating fault
When the ignition is on, the
lighting of this warning lamp,
accompanied by an audible signal and amessage in the multifunction screen, indicates
a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a CITROËN dealer or a qualified
workshop as soon as possible.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.
When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not
operate in manual mode.

There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the Pposition toanother position when the battery isflat.
To reduce fuel consumption when at
a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.

If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the message disappears.

87
5
Driving





Cruise control
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.

The cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph (40 km/h), as well as the engagement of:


-
fourth gear on a manual gearbox,

- second gear on a or automatic or electronic gearbox, in sequential mode,

- position A
on an electronic gearbox or position D
on an automatic gearbox.
Th
e cruise control is switched off
manually for by pressing the brake or clutch pedal or
on triggering of the ESP system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal.
Switching off the ignition cancels any programmed speed value. The controls o
f this system are grouped
together on stalk A.
1.Cruise control mode selection thumb wheel.
2. Value decrease button.3.
Value increase button.4.
Cruise control off/resume button.

Steering mounted controls
The cruise control cannot, in any circumstances, replace the need to respect speed limits, nor can it replace the need for vigilance and responsibilityon the par t of the driver. The pro
grammed information is grouped
together in the instrument panel screen.
5. Cruise control off/resume indication.
6. Cruise control mode selection indication. 7. Programmed speed value.


Displays in the instrument panel