2012 Citroen C CROSSER battery

3
Parking brake 112Manual gearbox 112CVT gearbox 113DCS gearbox 115Four wheel drive system 119Cruise control 121Audible rear parkingsensors 123Reversing camera 124
„„„„„„„
„
VII - DRIVING 112Î124
Bonnet 126Running out of fuel 126Petrol engine 127Diesel engine 128Checking levels 129Checks 130
„„„„„„
VIII - CHECKS 125Î131
Changing a wheel 132Changing a bulb 137Changing a fuse 146Battery 151Changing a wiper blade 153Towing 154Towing a trailer 156Fitting roof bars 157Accessories 158
„„„„„„„„„
IX - PRACTICALINFORMATION 132Î158
Engines 159Weights 160Dimensions 161Identifi cation markings 162
„„„„
X - TECHNICALDATA 159Î163
Audio CD system 164
CD changer 175Error messages 177Audio-Telematic System 178Navigation 180DVD mode 208Hands-free telephone 216
„„„„„„„
XI - AUDIO andTELEMATICS 164 Î 223
VISUALSEARCH 224 Î 229
ALPHABETICALINDEX 230Î233
CONTENTS

I
MONITORING
23

Warning lamp



is on



Cause



Actions/Observations



Diesel
preheating
Fixed This comes on when the
ignition switch is in the
ON position. Wait until this goes off before starting.
The duration for which this is on is determined
by the exterior climatic conditions.

Parking brake/
Brake fl uid
level
Fixed This comes on for a few
seconds when the ignition
is turned to "ON" then
goes off. It is accompanied by a message on
the instrument panel screen.
The parking brake is
applied or has not been
released fully. It is accompanied by a message on the
instrument panel screen. Release the parking
brake to switch off the warning lamp.
The brake fl uid level is
too low. It is accompanied by a message on the
instrument panel screen. Top up with brake fl uid
and contact a CITROËN dealer or a qualifi ed
workshop.

Emission
control system
Fixed or
fl ashing This comes on or fl ashes
in the event of a fault with
the system. Contact a CITROËN dealer or a qualifi ed
workshop.
It should go off a few seconds after starting
the engine.

Battery charge
Fixed This comes on if a
charging circuit fault
occurs. It should go off when the engine is started.
It is accompanied by a message on
the instrument panel screen. Check the battery
terminals (refer to the "Battery" section).

I
MONITORING
28


Message



is on



Cause



Solution - action



Observations



Dynamic
stability
control
system (ASC)
Fixed Dynamic stability control system
(ASC) fault. Contact a CITROËN
dealer or a qualifi ed
workshop.

Four wheel
drive system
Fixed Four wheel drive transmission
system fault. Contact a CITROËN
dealer or a qualifi ed
workshop.

Four wheel
drive system
temperature
Fixed The temperature of the four
wheel drive transmission
system is too high. Stop the vehicle and
contact a CITROËN
dealer or a qualifi ed
workshop. The vehicle switches
to front wheel
drive (2 WD) mode
automatically.

Automatic
headlamp
adjustment
system
Fixed The automatic headlamp
adjustment is faulty. Contact a CITROËN
dealer or a qualifi ed
workshop. Only on vehicle fi tted
with xenon bulbs.

Battery
charge
Fixed Battery charge fault. Stop the vehicle and
contact a CITROËN
dealer or a qualifi ed
workshop.

Ambient
temperature
Fixed The ambient temperature is
3 °C (37 °F) or below. Road icy.
Take care and drive
slowly. Caution: The road
may be icy even
when this screen is
not displayed.

I
!
!
MONITORING
32 The total distance is
displayed in zone 1
of
the screen and the trip
distance in zone 2
.
DISTANCE RECORDERS (A/B)

System for measuring the total distance
travelled by the vehicle during its
service life and the distance travelled in
a day or other period until it is reset to
zero by the driver.
Zero reset
With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear. When the engine is
running, this indicates
the temperature of the
coolant.
COOLANT TEMPERATURE
If the bar is close to the critical
position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.

You must stop your vehicle as soon
as it is safe to do so.


Wait a few minutes before switching
off the engine.

Wait for the engine to cool before
topping up the level. The cooling
system is pressurised.
When the engine is
running
, this indicates
the distance which can
still be travelled with the
fuel remaining in the tank
based on the average
fuel consumption over
the last few miles/
kilometres travelled.
RANGE
When the range is less than 30 miles
(50 km)
, dashes are displayed.
Refuel as soon as possible. The display
of the range is updated.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the
pressure to drop.
When the pressure has dropped,
remove the cap and top up the level, if
necessary.
Contact a CITROËN dealer or a
qualifi ed workshop. This fi gure may increase following a
change in the style of driving or the
relief, resulting in a reduction in the
current fuel consumption.
If you only add a few litres, the
value displayed will be incorrect.
Therefore, you must fi ll the tank
whenever possible.
When you disconnect the
battery, the previous fuel
consumption data is lost and the
value displayed will be different from
that displayed before the battery was
disconnected. The distance displayed
must be considered an approximate
indication.

I
MONITORING
36
Choice of the fuel consumption units
You can choose between different units
for displaying fuel consumption. On the menus screen:


)
press the INFO
button to select
"UNIT"
.

)
press and hold the INFO
button for
a few seconds to display the "UNIT"

screen.

)
press the INFO
button to scroll the
units (km/L, L/100km, mpg (US),
mpg (UK) and PREVIOUS) in suc-
cession.

)
press and hold the INFO
button for a
few seconds to confi rm your selection. In this case, the distance, speed and
quantity of fuel units will also be changed
in accordance with your choice of fuel
consumption unit. If the battery is disconnected, the
settings memory is cleared and
the default unit (km/L) is restored
automatically.


Choice of the temperature
display unit
You can choose between different units
for displaying the temperature.
On the menu screen:


)
press the INFO
button to select
the temperature unit setting
symbol (thermometer).

)
press and hold the INFO
button for
a few seconds to scroll the units
(°C and °F) in succession.
The mode selected is confi rmed.
If the battery is disconnected, the
settings memory is cleared and
the default unit (°C) is restored
automatically.


Choice of the reinitialisation of
the average consumption and average speed
You can choose between two average
fuel consumption and average speed
reinitialisation modes:


- automatic reinitialisation (choice 1)
,

- manual reinitialisation (choice 2)
.
On the menu screen:


)
press the INFO
button to select:

)

press and hold the INFO
button for a
few seconds to switch in succession
from reinitialisation mode 1



(automatic)

to reinitialisation mode 2 (manual)
.

The mode selected is confi rmed.

I
MONITORING
37
Choice of the display language
You can choose between different
languages for the display.
On the menu screen:


)
press the INFO
button to select
"LANGUAGE"
.

)
press and hold the INFO
button
for a few seconds to display the
"LANGUAGE"
screen.

)
press the INFO
button to scroll
the languages (Japonais, English,
Deutsch, Français, Espanol, Italiano,
"---" and PREVIOUS) in succession.

)
press and hold the INFO
button for
a few seconds to confi rm your se-
lection.
If you select the "---" setting, no
message will be displayed in
message display situations. If the battery is disconnected, the
settings memory is cleared and
the default language (ENGLISH) is
restored automatically.


Activation/deactivation of the"INFO" button sound

You can activate or deactivate the INFO
button sound.
On the menu screen:


)
press the INFO
button to se-
lect the INFO
button sound
activation/deactivation sym-
bol (located on menu 2/3)
.

)
press and hold the INFO
button for
a few seconds to scroll the choices
(ON, OFF) in succession.
The mode selected is confi rmed.
If the battery is disconnected, the
settings memory is cleared and
the default choice (ON) is restored
automatically.


Changing the display interval
of the "BREAK REMINDER"
message
You can change the display interval of
the "BREAK REMINDER"
message.
On the menu screen:


)
press the INFO
button to select
"ALERT" (located on menu 2/3)
.

)
press and hold the INFO
button
for a few seconds to display the
"ALERT"
screen.

)
press the INFO
button to select
the display interval of the "BREAK
REMINDER"
message.

)
press and hold the INFO
button for
a few seconds to confi rm.
If the battery is disconnected, the
settings memory is cleared and
the default value (OFF) is restored
automatically.

I
MONITORING
40
Set the time using the buttons as
indicated below:


)
with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK
button until the
time display fl ashes.

)
Press the appropriate button to set
the time:

Button
H:
to set the hours
The hours digits scroll when you press
this button.

Button M:
to set the minutes
The minutes digits scroll when you
press this button.

Button 00:
to reset the minutes to zero.


- from 1 to 29 min
:
rounded down to
the previous hour,

- from 30 to 59 min:
rounded up to
the next hour.
Automatic mode

In this mode, setting is automatic using
the signal from the RDS radio stations.

)
After setting the time, press the
DISP
button; the time display stops
fl ashing.
The digital clock does not display
seconds.
When the "minutes" display is set or
reset to zero, the clock starts at the
zero second of the minute selected.
The time setting is lost if the battery
is disconnected.


)
Turn button B
"TUNE" to the left or
to the right to select "CT ON"
(auto-
matic mode) or "CT OFF"
(manual
mode).

)
After selecting the mode, you can
exit the "Functions setting mode"
menu by pressing button B
"TUNE"
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "Functions setting mode" menu
automatically.

II
COMFORT
51

Electric mode (driver's seat only)


Forwards-backwards adjustment
Push the control forwards or rearwards
to move the seat to the position re-
quired.
Driver's seat cushion height and
angle adjustment
Pull or push the front of the control to raise
or lower the front of the seat cushion.
Pull or push the rear of the control to raise
or lower the rear of the seat cushion.
Pull or push the entire control to raise or
lower the entire seat cushion.
Seat back angle adjustment
Tilt the control forwards or rearwards to
straighten or tilt the seat back.
FRONT SEATS
To avoid discharging the battery, use
the electric mode with the engine
running.