Page 134 of 244
IX
!
PRACTICAL INFORMATION
132
CHANGING A WHEEL
1.
Wheelbrace.
Used to remove the wheel trim and
the wheel fi xing bolts.
2.
Jack.
Used to raise the vehicle.
3.
Handle.
Used to extend the jack.
4.
Removable towing eye.
Refer to the "Towing" paragraph.
Other accessories
Wheel with trim
When removing the wheel
, remove
the trim fi rst using the handle 3
, pulling
at the notch.
When refi tting the wheel
, refi t the trim
starting by placing its notch F
(indicated
on the back of the trim) opposite the
valve G
and press on its outer edge
with the palm of your hand.
List of tools
When changing a wheel, ensure
that the four wheels are of identi-
cal specifi cation and brand. When storing, take care to secure
the tool bag D
fi rmly using the fi xing
band C
.
Access to the tools
The tools are stored in the storage
compartment in the boot right-hand trim.
To gain access to them:
)
open the boot,
)
turn button A
to the left,
)
remove the cover B
,
)
remove the fi xing band C
and take
out the tool bag D
containing the
tools,
)
take the jack E
in your hand and re-
move it from its fi xing position.
Page 140 of 244
IX
PRACTICAL INFORMATION
138
Changing direction indicator bulbs (1)
Coloured bulbs must be replaced
with bulbs of identical specifi cation
and colour.
)
Turn the bulb holder A
to the left
and remove it.
)
Pull the bulb and change it.
To r efi t, carry out these operations in
reverse order.
Access to the bulbs on the left-hand
side
When you change a bulb on the left-
hand side, remove the relay box fi xing
nut B
and move the relay box towards
the rear.
Access to the bulbs on the right-
hand side
When you change a bulb on the right-
hand side:
)
Remove the screenwash reservoir
fi xing C
and move the reservoir to-
wards the rear.
)
Remove the coolant reservoir fi xing
nut D
.
)
Remove the clip E
and raise the res-
ervoir moving it towards the front.
Page 142 of 244
IX
PRACTICAL INFORMATION
140
Changing integrated direction
indicator side repeaters
Changing foglamp bulbs (5)
)
Push the repeater A
towards the
rear and detach it.
)
Unclip the repeater.
)
Disconnect the repeater connector
and change the repeater.
To r efi t, carry out these operations in
reverse order.
To obtain repeaters, contact a CITROËN
dealer or a qualifi ed workshop.
)
Turn the wheel fully out for easy
access to the fl ap A
located in the
wheelarch.
)
Using a screwdriver, remove the four
clips B
located in the wheelarch.
Page 149 of 244
IX
PRACTICAL INFORMATION
147
Dashboard fuses
The fuseboxes are placed in the lower
dashboard behind the enclosed storage
compartment (left-hand side).
Access to the fuses
)
Open the cover A
,
)
Pull it towards you to extract it,
)
Change the fuse (refer to the cor-
responding paragraph).
Fuse N°
Rating
Functions
1*
30 A
Heating.
2
15 A
Brake lamps, third brake lamp, built-in systems
interface.
3
10 A
Rear foglamps.
4
30 A
Windscreen wipers and screenwash.
5
10 A
Diagnostic socket.
6
20 A
Central locking, door mirrors.
7
15 A
Audio equipment, telematics, multifunction screen,
Bluetooth system.
8
7.5 A
Remote control key, air conditioning control unit,
instrument panel, switch panel, steering mounted
controls.
9
15 A
Multifunction screen, instrument panel.
10
15 A
Built-in systems interface.
11
15 A
Rear wiper.
12
7.5 A
Instrument panel, 4 wheel drive control unit,
air conditioning control panel, ABS control
unit, multifunction screen, automatic headlamp
adjustment, heated seats, airbag control unit,
steering wheel angle sensor, sunroof, rear screen
demisting, remote control.
13
-
Not used.
14
10 A
Ignition switch.
15
20 A
Sunroof.
16
10 A
Door mirrors, audio equipment, telematics.
Page 150 of 244
IX
!
PRACTICAL INFORMATION
148
Access to the fuses
)
Open the cover A
,
)
Pull it towards you to extract it,
)
Change the fuse (refer to the cor-
responding paragraph).
* The maxi-fuses provide additional protection for the electrical systems. All work on the maxi-fuses must be carried
out by a CITROËN dealer or a qualifi ed workshop.
Fuse N°
Rating
Functions
17
10 A
4 wheel drive control unit.
18
7.5 A
Reversing lamps, parking sensors control unit,
reversing camera, airbag control unit.
19
15 A
Accessories socket.
20*
30 A
Electric window controls.
21
*
30 A
Rear screen demisting.
22
7.5 A
Heated door mirrors.
23
-
Not used.
24
25 A
Driver's electric seat, footwell lighting, rear bench
seat release.
25
30 A
Heated seats.
Page 153 of 244
IX
PRACTICAL INFORMATION
151 The battery A
is located under the bon-
net on the left.
To gain access to it:
)
open the bonnet using the interior re-
lease lever, then the exterior safety
catch,
)
secure the bonnet stay.
BATTERY
Access to the battery
)
Connect the red cable to the posi-
tive terminal (+) of the fl at battery A
,
then to the positive terminal (+) of
the slave battery B
.
)
Connect one end of the green or
black cable to the negative terminal
(-) of the slave battery B
.
)
Connect the other end of the green
or black cable to an earth point C
on
the broken down vehicle, as far as
possible from the battery (for exam-
ple, right-hand engine mounting).
)
Start the engine of the assisting ve-
hicle.
)
Operate the starter, let the engine
run.
)
Wait until the engine returns to idle
and disconnect the cables.
)
Raise the front of the cover 1
to re-
lease the three clips 2
.
)
Then pull the cover 1
towards you
to release the clip 3
and remove the
cover.
Check the electrolyte level regularly.
If necessary, top up the level with dis-
tilled water.
Starting using another battery
Looking for an earth point at
the right-hand engine mounting
Page 155 of 244
IX
PRACTICAL INFORMATION
153
CHANGING A WIPER BLADE
Removin
g a front or rear wiper blade
)
Raise the corresponding wiper arm.
)
Remove the wiper blade, sliding it
towards the outside.
Fitting a front or rear wiper blade
)
At the front, check the size of the
wiper blade as the shorter blade is
fi tted on the right-hand side of the
vehicle.
)
Put the corresponding new wiper
blade in place and fi x it.
)
Fold down the wiper arm carefully.
Page 156 of 244
IX
!
PRACTICAL INFORMATION
154
TOWING
Access to the tools
Having your vehicle towed on a flatbed
)
Below the front bumper, install the
towing system on the towing eye 1
.
The towing eye and the tools are stored
in the storage compartment in the right-
hand boot trim.
To gain access to them:
)
open the boot,
)
turn button A
to the left,
)
remove the cover B
,
)
remove the fi xing band C
and take out
the tool bag D
containing the tools,
)
take the towing eye and the tools re-
quired out of the tool bag.
Place the gear lever in neutral.
Always have the vehicle
towed on a fl atbed.
Never have the vehicle towed with
the four wheels on the ground, this
could damage the transmission.
The vehicle must not be towed with
the front or rear wheels on the ground
even if it is in front "2WD" (2 wheel
drive) mode.
