2012 CITROEN C-CROSSER coolant

I
21
INSTRUMENT PANEL
Panel grouping together the dials and
warning/indicator lamps. These inform
the driver of the activation/deactivation
of a system or of the occurrence of a
fault.
3.
Instrument panel screen:


- Warning and status displays.

- Total and trip distance recorders.

- Service indicator.

- Coolant temperature.

- Trip computer information.

- Cruise control setting.

- Dashboard lighting and parameter
settings.

- Fuel level.

- Ambient temperature.

- Transmission mode.


Screen type 1
Screen type 2


1.
Rev counter.

2.
Speedometer.

I
MONITORING
26
Warning messages (ignition at "ON")


Message



is on



Cause



Solution - action



Observations



ABS
Fixed Anti-lock braking system
(ABS) fault. Contact a CITROËN dealer
or a qualifi ed workshop. The vehicle retains
conventional braking
without assistance
but you are advised
to stop.

Braking
system
Fixed Associated warning
lamp.
The level of brake
fl uid in the reservoir is
too low. Stop and top up, otherwise
contact a CITROËN dealer
or a qualifi ed workshop. If the message
remains on after
topping up, contact a
CITROËN dealer or
a qualifi ed workshop.
Associated warning
lamp.
Braking system fault. Contact a CITROËN dealer
or a qualifi ed workshop.
You must stop as
soon as it is safe
to do so.


Parking brake
on
Fixed You have moved off with
the parking brake still
applied. Release the parking brake.

Coolant
temperature
Flashing
High engine temperature. If the message fl ashes
,
wait for the engine to cool
before topping up the level,
if necessary.

You must stop
your vehicle as
soon as it is safe
to do so.


Flashing
If the message fl ashes
and the service
warning light comes
on
, contact a CITROËN
dealer or a qualifi ed
workshop without delay.

Seat belt
Fixed The driver has not fastened
or has unfastened his seat
belt. Fasten your seat belt. There is an
intermittent audible
signal above 5 mph
(8 km/h).

I
31 The total distance is dis-
played in zone 1
of the
screen and the trip dis-
tance in zone 2
(refer to
the "Distance recorders"
section).
Distance recorder (A and B)
INFORMATION IN THE
IN
STRUMENT PANEL SCREEN
Information displa
y
With the ignition on, press the INFO

button, located on the dashboard to the
right of the instrument panel, to display
the various information in succession:


- distance recorder A,

- distance recorder B,

- service indicator,

- coolant temperature,

- range,

- trip computer,

- setting menu. This displays the dis-
tance and the number of
months remaining before
the next service in line
with with the manufac-
turer’s servicing sched-
ule (refer to the "Service
indicator" section).
Service indicator
When the engine is run-
ning, this indicates the
temperature of the cool-
ant (refer to the "Coolant
temperature indicator"
section).
Coolant temperature When the engine is
running, this indicates
the number of miles
(kilometres) which can
still be travelled with the
fuel remaining in the tank
based on the average
fuel consumption over
the last few miles (kilometres) travelled
(refer to the "Range" section).
Range
This indicates the aver-
age fuel consumption,
the average speed and
the current fuel con-
sumption (refer to the
"Trip computer" section).
Trip computer

When the vehicle is sta-
tionary
, this allows the
user to change the follow-
ing settings (refer to the
"Setting menu" section):


- the display language,

- the temperature dis-
play units,

- the fuel consumption units,

- the option to reset the average
fuel consumption and the average
speed,

- the break (rest) reminder display in-
terval.


Setting menu

I
!
!
MONITORING
32 The total distance is
displayed in zone 1
of
the screen and the trip
distance in zone 2
.
DISTANCE RECORDERS (A/B)

System for measuring the total distance
travelled by the vehicle during its
service life and the distance travelled in
a day or other period until it is reset to
zero by the driver.
Zero reset
With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear. When the engine is
running, this indicates
the temperature of the
coolant.
COOLANT TEMPERATURE
If the bar is close to the critical
position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.

You must stop your vehicle as soon
as it is safe to do so.


Wait a few minutes before switching
off the engine.

Wait for the engine to cool before
topping up the level. The cooling
system is pressurised.
When the engine is
running
, this indicates
the distance which can
still be travelled with the
fuel remaining in the tank
based on the average
fuel consumption over the
last few miles/kilometres
travelled.
RANGE
When the range is less than 30 miles
(50 km)
, dashes are displayed.
Refuel as soon as possible. The display
of the range is updated.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the
pressure to drop.
When the pressure has dropped,
remove the cap and top up the level, if
necessary.
Contact a CITROËN dealer or a
qualifi ed workshop. This fi gure may increase following a
change in the style of driving or the
relief, resulting in a reduction in the
current fuel consumption.
If you only add a few litres, the
value displayed will be incorrect.
Therefore, you must fi ll the tank
whenever possible.
When you disconnect the
battery, the previous fuel
consumption data is lost and the
value displayed will be different from
that displayed before the battery was
disconnected. The distance displayed
must be considered an approximate
indication.

VIII
127
PETROL ENGINE


1. Screenwash and headlamp wash
reservoir.

2. Coolant reservoir.

3. Power steering fl uid reservoir.

4. Brake fl uid reservoir.

5. Fusebox.

6. Battery.

7. CVT gearbox dipstick.

8. Radiator cap.

9. Engine oil dipstick.

10. Engine oil fi ller cap.

11. Air fi lter. Access for checking the levels of the various fl uids and the replacement of certain components.

VIII
128
DIESEL ENGINE
Access for checking the levels of the various fl uids and the replacement of certain components.


1. Coolant reservoir.

2. Power steering fl uid reservoir.

3. Screenwash and headlamp wash
reservoir.

4. Brake fl uid reservoir.

5. Fusebox.

6. Battery.

7. Engine oil dipstick.

8. Engine oil fi ller cap.

9. Air fi lter.

VIII
CHECKS
129
CHECKING LEVELS
Brake fluid level
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.

Oil level

The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 30 minutes.
The check is carried out either when
the ignition is switched on using the oil
level indicator on the instrument panel,
or using the dipstick.
It is normal to top up the engine oil between
services. The manufacturer recommends
that the oil level be checked, and topped up
if necessary, every 3 000 miles (5 000 km).
The brake fl uid level should be
between the "MAX" and "MIN"
marks.
If it is not, check the brake pad
wear.

Changing the brake fl uid
Refer to the servicing booklet for details
of the interval for this operation.


Coolant level

The coolant level must be mea-
sured when the engine is cold
and should be between the
"LOW" and "FULL" marks.
When the engine is warm, the
temperature of the coolant is regulated
by the fan. This can operate with the ig-
nition off.
On vehicles which are fi tted with a
particle emission fi lter, the fan may
operate after the vehicle has been
switched off, even if the engine is
cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work.
Screenwash and headlamp
wash * fluid

Check the fl uid level regularly,
using the gauge.

*
According to country.
Changing the engine oil
Refer to the servicing booklet for details
of the interval for this operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.

Oil specifi cation
The oil must correspond to your engine
and conform to the manufacturer's recom-
mendations.

Fluid specifi cation
The brake fl uid must conform to the
manufacturer's recommendations and
fulfi l the DOT4 standards.

Changing the coolant fl uid
Refer to the servicing booklet for details
of the interval for this operation.

Fluid specifi cation
The coolant must conform to the manu-
facturer's recommendations.


Fluid specifi cation
This fl uid must conform to the manufac-
turer's recommendations for optimum
cleaning.

Power steering fluid level

Check the fl uid level with the engine at
idle.
Check that the power steering fl uid
level is always between the "MAX" and
"MIN" marks and top up if necessary.

Fluid specifi cation
This fl uid must conform to the manufac-
turer's recommendations.
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
If a level drops signifi cantly, have the
corresponding system checked by a
CITROËN dealer or a qualifi ed work-
shop.
When working under the bonnet, take
care as certain areas of the engine may
be extremely hot (risk of burns).

IX
PRACTICAL INFORMATION
138

Changing direction indicator bulbs (1)
Coloured bulbs must be replaced
with bulbs of identical specifi cation
and colour.


)
Turn the bulb holder A
to the left
and remove it.

)
Pull the bulb and change it.
To r efi t, carry out these operations in
reverse order.
Access to the bulbs on the left-hand
side
When you change a bulb on the left-
hand side, remove the relay box fi xing
nut B
and move the relay box towards
the rear.
Access to the bulbs on the right-
hand side
When you change a bulb on the right-
hand side:


)
Remove the screenwash reservoir
fi xing C
and move the reservoir to-
wards the rear.

)
Remove the coolant reservoir fi xing
nut D
.

)
Remove the clip E
and raise the res-
ervoir moving it towards the front.