2012 CITROEN C-CROSSER lock
[x] Cancel search: lockPage 26 of 244
I
MONITORING
24
Warning lamp
is on
Cause
Actions/Observations
Driver's
seat belt not
fastened
Fixed The driver has not
fastened or has
unfastened their seat belt. This is accompanied by a message on
the instrument panel screen.
Fasten the driver's seat belt.
ABS
Fixed This comes on if an anti-
lock braking system fault
occurs. It is accompanied by a message in the
instrument panel screen. The vehicle retains
conventional braking without assistance but
you are advised to stop. Have it checked by
a CITROËN dealer or a qualifi ed workshop.
Airbags and
pretensioners
Fixed This comes on for a few
seconds when the ignition
is turned to "ON" then
goes off. It should go off when the engine is started. If it
does not go off, contact a CITROËN dealer or
a qualifi ed workshop.
This comes on if an
airbag or pretensioner
fault occurs. It is accompanied by a message on
the instrument panel screen. Have the system
checked by a CITROËN dealer or a qualifi ed
workshop without delay.
Dynamic
stability control
system (ASC)
Fixed This comes on if
a dynamic stability control
system fault occurs. It is accompanied by a message on
the instrument panel screen. Have the system
checked by a CITROËN dealer or a qualifi ed
workshop without delay.
Page 27 of 244
I
MONITORING
25 Each time the engine is started: a series of warning lamps and/or messages come on, applying a checking self test. They go
off after a few seconds. Engine running: the warning lamp or the message becomes a warning if it remains on continuously
or fl ashes. This initial warning may be accompanied by an audible signal and a message on the screen. Do not ignore these
warnings.
The messages displayed may differ between the type 1 instrument panel and the type 2 instrument panel.
When the cause of the appearance of the warning lamp or warning message has been rectifi ed, the warning disappears
from the screen automatically. If the cause of the warning is not rectifi ed, you can return to the previous screen at any time
by pressing the INFO
button on the dashboard.
The symbol "!"
is displayed.
To return to the previous screen (with the "!"
symbol), you must press the INFO
button several times.
Warning messages (ignition at "OFF")
You can close the warning messages which show these symbols in order to move on to the next screen.
To do this, press the INFO
button according to the symbol displayed.
Press briefl y
. Press and hold
.
Symbols which appear in the top right corner of the screen.
Message
is on
Cause
Solution - action
Observations
Key in
ignition
Fixed The driver's door is open
and you have forgotten
to remove the key from
the ignition. Turn the ignition switch
to the LOCK position
and remove the key. Only if the engine has
been started.
An intermittent audible
signal is heard.
Lighting
left on
Fixed You have forgotten to
switch off the vehicle
lighting. Switch off the vehicle
lighting by placing the
stalk at OFF. An intermittent audible
signal is heard.
Page 28 of 244
I
MONITORING
26
Warning messages (ignition at "ON")
Message
is on
Cause
Solution - action
Observations
ABS
Fixed Anti-lock braking system
(ABS) fault. Contact a CITROËN dealer
or a qualifi ed workshop. The vehicle retains
conventional braking
without assistance
but you are advised
to stop.
Braking
system
Fixed Associated warning
lamp.
The level of brake
fl uid in the reservoir is
too low. Stop and top up, otherwise
contact a CITROËN dealer
or a qualifi ed workshop. If the message
remains on after
topping up, contact a
CITROËN dealer or
a qualifi ed workshop.
Associated warning
lamp.
Braking system fault. Contact a CITROËN dealer
or a qualifi ed workshop.
You must stop as
soon as it is safe
to do so.
Parking brake
on
Fixed You have moved off with
the parking brake still
applied. Release the parking brake.
Coolant
temperature
Flashing
High engine temperature. If the message fl ashes
,
wait for the engine to cool
before topping up the level,
if necessary.
You must stop
your vehicle as
soon as it is safe
to do so.
Flashing
If the message fl ashes
and the service
warning light comes
on
, contact a CITROËN
dealer or a qualifi ed
workshop without delay.
Seat belt
Fixed The driver has not fastened
or has unfastened his seat
belt. Fasten your seat belt. There is an
intermittent audible
signal above 5 mph
(8 km/h).
Page 32 of 244
I
MONITORING
30
Prevention messages Information messa
ges (ignition at "ON")
Message
is on
Status of the system
2WD two wheel
drive system
Flashing When the "2WD" (2 wheel drive) mode is selected using the
transmission mode selector.
4WD four wheel
drive system
Flashing When the "4WD" (4 wheel drive) mode is selected using the
transmission mode selector.
This mode is the default mode.
4WD LOCK four
wheel drive system
Flashing When the "LOCK" (4 wheel drive) mode is selected using the
transmission mode selector.
Ambient
temperature
Fixed This indicates the ambient temperature.
When the vehicle is stationary or if the speed is below 12 mph (20 km/h)
the temperature displayed may not be the true temperature.
Display
is on
Cause
Solution - action
Observations
Service
indicator
Fixed Informs the driver of
the time remaining
before the vehicle's
scheduled service. Contact a CITROËN
dealer or a qualifi ed
workshop. This is displayed for a few
seconds when the ignition is
switched on.
Break
advised
Fixed Informs the driver that
they should stop to
take a break. You are advised to
take a break. This is displayed when the
driving time that you set
previously is reached.
An audible signal is heard
3 times and is then heard every
5 minutes until the vehicle stops.
Page 41 of 244
I
MONITORING
39
MONOCHROME SCREEN
This provides the following information:
- the time,
- audio system information (refer to
the "Audio and Telematics" section).
Setting the time
The digital clock can be set in automatic
mode
or in manual mode
.
Selecting the Setting
Select the automatic mode
or the
manual mode
as follows:
)
Press button A
"PWR" to switch on
the audio system.
)
Access the setting mode by pressing
button B
"TUNE" for approximately
2 seconds.
)
Press button B
"TUNE" several
times to scroll through the various
menus and select the CT menu
(clock time).
The order of the menus is the following:
AF/CT/REG/TP-S/PTY display language/
SCV/PHONE/Functions setting mode
OFF.
Automatic mode
This mode permits automatic setting
of the local time using the signal from
RDS stations.
The symbol "CT"
appears on the screen.
Manual mode
This mode permits manual setting of
the time using the audio equipment
buttons.
It can also be used when the "Automatic
mode" displays an inaccurate time, when
the local RDS stations are broadcasting
from a different time zone.
Page 42 of 244
I
MONITORING
40
Set the time using the buttons as
indicated below:
)
with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK
button until the
time display fl ashes.
)
Press the appropriate button to set
the time:
Button
H:
to set the hours
The hours digits scroll when you press
this button.
Button M:
to set the minutes
The minutes digits scroll when you
press this button.
Button 00:
to reset the minutes to zero.
- from 1 to 29 min
:
rounded down to
the previous hour,
- from 30 to 59 min:
rounded up to
the next hour.
Manual mode
Automatic mode
In this mode, setting is automatic using
the signal from the RDS radio stations.
)
After setting the time, press the
DISP
button; the time display stops
fl ashing.
The digital clock does not display
seconds.
When the "minutes" display is set or
reset to zero, the clock starts at the
zero second of the minute selected.
The time setting is lost if the battery
is disconnected.
)
Turn button B
"TUNE" to the left or
to the right to select "CT ON"
(auto-
matic mode) or "CT OFF"
(manual
mode).
)
After selecting the mode, you can
exit the "Functions setting mode"
menu by pressing button B
"TUNE"
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "Functions setting mode" menu
automatically.
Page 44 of 244
I
42
Setting the time
The digital clock is set automatically
.
This mode enables the system to set
the local time automatically using the
signal from the RDS stations.
)
On the control panel, press button A
(SET) to access the "Settings"
menu.
)
On the touch screen, press button B
to access the "System"
menu.
The system settings screen is displayed.
"Info" menu
On the control panel, press button D
(INFO)
to access the "Info"
screen and
consult:
- "Support info"
to display the soft-
ware and data versions,
- "Vehicle position"
to display the
GPS location of the vehicle,
- "Calendar"
to make a note of
events, birthdays, etc.,
- "Journey"
to display the average
speed, fuel consumption, distances
and driving time,
- "Environment"
to display the alti-
tude, the atmospheric pressure, the
exterior temperature (the ice symbol
is displayed if there is a risk of ice),
- "Air conditioning"
to display the
information relating to the air condi-
tioning,
- "Mobile phone"
to enter a number,
delete a character, make or receive
a call.
"Route" menu
On the control panel, press button E
(NAVI)
to access the "Route Menu"
screen and select:
- "Detour"
to make a detour through
a specifi ed region,
- "Itinerary"
to change the route,
- "View route"
to display a route in
different ways,
- "Delete route"
to delete a route,
- "Nearby POI"
to search for the
POIs in the surrounding area.
Page 56 of 244
II
COMFORT
54
Rear armrest
Lower the armrest to use it.
To return to the initial confi guration, push
the armrest until it locks in its vertical
position.
Access to the third row
The passenger gains access to the
third row of seats by tilting a second
row seat.
To put this seat back in place, refer to
the following pages.