2012 Citroen BERLINGO MULTISPACE RHD change wheel

144


Changing a wheel



1. PARKING THE VEHICLE



- The occupants must get out of the
vehicle and wait in a safe location.

- If possible, park the vehicle on
level, stable and non-slippery
ground.

- Apply the parking brake, switch
off the ignition and engage fi rst or
reverse gear.
- If available, place a chock under
the wheel diagonally opposite the
one to be changed.
If the vehicle is fi tted with a towbar,
it is sometimes necessary to raise
the vehicle slightly to make it easier
to remove the spare wheel from its
carrier.
On certain types of ground and/or
if considerable loads are being
transported, call a CITROËN dealer or
a qualifi ed workshop.

CHANGING A WHEEL

2. TOOLS



- The tools are stowed in a storage
compartment located under the
front seat. If necessary, move the
seat forward to access the storage
compartment from the rear.

- Unscrew the nut then take out the
jack and the wheelbrace.


1.
Wheelbrace.

2.
Jack.

3.
Alloy wheel embellisher remover.

4.
Chock.
The jack and the tool kit are specifi c to
your vehicle. Do not use them for other
purposes.

145
7


Changing a wheel



3. SPARE WHEEL


- Unscrew the bolt using the
wheelbrace until the carrier is
lowered fully.

- Open the rear doors to gain access
to the spare wheel.
- Detach the carrier from the hook
and place the spare wheel near the
wheel to be changed.

QUICK HEL
P

146


Changing a wheel



4. OPERATING PROCEDURE


- Place the jack in contact with the
locating point provided, the one
which is closest to the wheel to
be changed. Ensure that the jack
is straight and that the base of
the jack is fully in contact with the
ground.

- Extend the jack to lift the wheel
clear of the ground.

- Resume and complete the
unscrewing of the wheel bolts.

- Remove the bolts and remove the
wheel.

- Remove the trim using the removal
tool.

- Loosen the wheel bolts and start
unscrewing them. Do not extend the jack until you have
started unscrewing the bolts on the
wheel to be changed and have placed
the chock under the wheel diagonally
opposite.

151
7


Changing a bulb

QUICK HELP


4.
Foglamps

Type C
, H1 - 55W


- Remove the three clips and the
screw securing the wheelarch liner,
located below the bumper.

- Move the wheelarch liner upwards.

- Remove the foglamp by removing
the screw, which can be accessed
via the hole provided for this
purpose in the bumper, using a
Torx
© 30 screwdriver.

- Unclip the foglamp by squeezing
the clip to release it.

-
Remove the foglamp from the outside.

- Turn the yellow cover a 1/4 turn to open.

- Separate the clips which secure
the base of bulb on each side to
release the bulb.

- Remove the bulb by pulling,
keeping it straight.

- Insert the new bulb, reposition the
clips around the base of the bulb
and carry out the operations in
reverse order to put the lamp unit
and the bumper back in position.



SIDE REPEATER


Ty p e A
, WY5W - 5W (amber)


- Push the repeater towards the rear
and disengage it by pulling the
front.

- Contact a CITROËN dealer to
obtain a new repeater which is a
sealed component.

- To refi t, engage the repeater
towards the rear and bring it
towards the front.


COURTESY LAMPS


Type A
, 12V5W - 5W


- Unclip the lens by sliding a
screwdriver in the slots on each
side of the courtesy lamp.

- Pull the bulb out and change it.

- Clip the lens in its housing and
ensure that it is secured correctly.

Front/Rear