2012 CHEVROLET TAHOE ECU

Black plate (3,1)Chevrolet Tahoe Police and Special Service Packages - 2012
Seats and Restraints 3-3
Notices for Customer
Installed Equipment
Read the following notices before
installing equipment on your
specialty vehicle.
Notice:GM-approved service
procedures must be followed to
remove and reinstall the
instrument panel to the pad in
order to ensure proper airbag
deployment. Notice:
Do not mount equipment
on the passenger side of the
instrument panel top pad
deployment zone. Equipment
should not be mounted on or
around the passenger airbag
opening because of a deploying
airbag. To allow the airbag to
perform as it was designed, do
not mount equipment inside the
airbag deployment zone.
Notice: The police vehicle has
roof-rail airbags. Do not mount a
security barrier such that the
ends of the barrier or brackets
are within the roof-rail
deployment zones. Notice:
The police vehicle has
roof-rail airbags and a rollover
sensor. The rollover sensor is
mounted on the centerline of the
vehicle between the driver and
right front passenger positions.
If the vehicle has bucket seats,
the rollover sensor will be
exposed. Do not mount
equipment within 25 mm (1 in) of
the rollover sensor. This may
affect the performance of the
airbag system. To allow the
airbags to perform as they are
designed, do not mount
equipment near this area.
Notice: Avoid installing wiring for
roof-rail emergency lighting or
radio antennas that may restrict
the proper deployment of the
roof-rail airbags.

Black plate (2,1)Chevrolet Tahoe Police and Special Service Packages - 2012
9-2 Driving and Operating
The following guidelines can help
you with proper loading and load
distribution when installing
additional equipment on the Tahoe
Police Package.
{WARNING
Do not load the vehicle any
heavier than the Gross
Vehicle Weight Rating
(GVWR), or either the
maximum front or rear Gross
Axle Weight Rating (GAWR).
This can cause systems to
break and change the way the
vehicle handles. This could
cause loss of control and a
crash. Overloading can also
shorten the life of the vehicle. Adding Equipment to Your
Vehicle
Before adding accessories or
equipment to your police vehicle,
there are some things you need
to know:
.The police vehicle's maximum
capacity weight.
.The weight of your police
vehicle, including a full tank of
fuel but without a driver and
passengers.
.The weight of items you plan on
adding to your police vehicle,
like roof mounted light bar(s),
push bumpers, security
barrier(s), rear storage
organizer, highway flares, fire
extinguishers, weapons,
ammunition, radios, and video
equipment.
.The weight and number of
passengers you intend to carry
in your vehicle.
.The total weight of any
additional cargo you intend to
carry in your vehicle.
When planning your vehicle
equipment installation remember not
to exceed the Gross Vehicle Weight
Rating (GVWR) or the Gross Axle
Weight Rating (GAWR) of the front
or rear axles. To keep the available
load weight less than the vehicle
capacity weight, you may need to
limit the number of passengers you
carry in your vehicle or change your
choice of additional equipment.

Black plate (6,1)Chevrolet Tahoe Police and Special Service Packages - 2012
15-6 Special Equipment Options
6. Reconnect the negative (−)battery cable to the battery.
Torque the bolt to 5 Y
(3.6 lb ft).
7. Reset the clock time and radio pushbuttons as desired.
The 12‐volt battery power is
supplied through two underhood
mega fuses, one 125 amp and one
60 amp. This underhood power is
fed to the breaker/relay center via a
harness that passes through the
driver side front of the dash, and
routes across the instrument panel
to a position forward of the glove
box. The breaker/relay center is
mounted to the instrument panel
structure forward of the glove box.
The center includes a plastic
bracket, two relays, two 30 amp
breakers and three 50 amp mega
circuit breakers. Two 30 amp breakers supply power
from the underhood 60 amp mega
fuse through the contacts of the
control relays to 3.0 mm² (12 gauge)
blunt cut wires. These two blunt cut
leads are part of wire coil under the
instrument panel near the center of
the vehicle.
Each relay is operated by a 0.5 mm²
(20 gauge) blunt cut, light or dark
blue control lead included in the
122 cm (4 ft) loop of wire coiled
under the instrument panel.
Three 50 amp mega circuit
breakers, protected by three fusible
links, supply power directly from the
underhood 125 amp mega fuse
through three, 5.0 mm² (10 gauge)
wires. Two of the wires are routed
through the body harness to buss
junction blocks in the left rear of the
cargo area and secured near the
jack and tools. This 122 cm (4 ft) of
coiled wires can be accessed by
removing the cup holder on the top
of the trim panel. The third 5 mm²
(10 gauge) wire is a blunt cut lead
which is part of the 122 cm (4 ft)
loop of wire coiled under the
instrument panel near the center of
the vehicle.
An 8 mm² (8 gauge) ground lead is
also provided, and it is located
under the front passenger sill plate.
It can be accessed by removing the
sill plate and pulling the loop of wire
at the front of the plate. The lead is
122 cm (4 ft) long.

Black plate (22,1)Chevrolet Tahoe Police and Special Service Packages - 2012
15-22 Special Equipment Options
Wiring Provisions for
Vehicle Grille Lamps,
Flasher, and Speaker/
Siren - SEO 6J3
Alternating Signal Flasher
A. Blunt cut ends for the Customer-Furnished Grille
Lamps and Customer-Furnished
Siren/Speaker
B. Control Wires from In-Line Connector in Forward Lamp
Harness for
Customer-Furnished Grille
Lamps and Speaker The SEO 6J3 wiring provision option
consists of a 1.5 m (5 ft) wiring
harness coiled underneath the
instrument panel on the passenger
side. The wiring circuits are routed
from underneath the instrument
panel to a 30 cm (1 ft) coil secured
in the area behind the grille. There
are four 1.0 mm² (16 gauge) wires
for connecting to the grille lights
(GRY, TAN) and siren speaker
(LT BU, LT GN)
The SEO 6J3 wiring provision also
includes one 0.8 mm² (18 gauge)
control wire for the SEO 6J7 exterior
lamps emergency flashing system.
When option SEO 6J7 is installed
without option SEO 6J3, only the
dark green/red control wire is
provided for connection to
customer-furnished 12-volt
switching to turn the emergency
flashing system on or off.