2012 AUDI S7 spare wheel

254 What do I do now?
-Never st ore the inflatable spare tire or
jack and tools in the passenger com­
partm ent.
- Always s tore a ll jacking equipment,
too ls, and the inflatable spare tire in
the luggage compartment.
- Tighten the knurled retaining screw for
the inflatable spare tire securely.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
" After you experience a tire fa ilure, pull t he
ca r well away from moving traffic and try to
r each
level gro und before you stop c::> ,&. .
" All passengers sho uld leave the car and
move to a safe loca tion (fo r inst ance, behind
the g uardrail)
c::> ,&. .
" Engage the parking brake to prevent your
vehicle from ro lling unintentionally
c::> ,&. .
" Move selecto r lever to pos ition Pc::> ,&. .
" If you are tow ing a trailer, unh itch the tra il­
er from your veh icle .
" Take the
jack and the spare tire out of the
l uggage compartment
c::> page 252 ,
c::> page 253.
.&_ WARNING
You or your p assengers cou ld be injured
while changing a whee l if you do not fol ­
low t hese safety preca utions:
- If you have a fl at t ire, move a safe dis­
tance off the road . Tur n off the engine,
t ur n the emergency flas hers o n and use
other warning dev ices to alert other mo­
torists .
- Make su re that passengers wait in a safe
place away from the vehicle and well
away from the road and traff ic.
- To help p revent the veh icle from mov ing
sudden ly and possibly slipping off the
jack, always fully set the parking brake and block th e whee l diago na lly opposite
-
the wheel be ing changed . When one
front wheel is lifted off the ground, plac­ ing the Automatic Transmission in "P"
(Park) will
not prevent the vehicle from
mov ing .
- Before you change a wheel, be sure t he
ground is level and firm. If necessary, use a sturdy board under the jack .
- After insta lling the spare wheel, make
sure tha t you replace the fla t tire/wheel
i n its storage area prope rly and tighten
the knurled retain ing screw secu rely.
Changing a wheel
When you change a wheel , follow these ­
quence described below step-by-step and in
exactly that order.
1. Remove the decorative wheel cover* . For
more details see also
c::> page 255, Deco­
rative wheel covers
or c::> page 255,
Wheels with wheel bolt caps.
2 . Loosen the wheel bolt s c::>page 255.
3. Loc ate the p roper moun ting poin t for th e
jac k an d align the jack be low that poin t
c::>page 256 .
4. Raise the car with the jack c::> page 256.
5. Remove the wheel with the flat tire and
then insta ll
the spare c::> page 257.
6. Tig hte n all whee l bolts lightly .
7.
Lower the vehicle wi th the jack .
8 . Use the wheel bolt w rench and
firmly
t ig ht en al l w heel bo lts c::> page 25 5.
9. Re place the decora tive wheel cover* .
A WARNING
Always read and fo llow all WA RNINGS and
i nformat io n
c::> & in Raising the vehicle on
page 257
and c::> page 258 .
After changing a wheel
A wheel change is not complete withou t the
doing the following .
" Replace the too ls and the jac k in their prop-
er lo cat io n. .,.

.. The fault wheel will not fit ins ide the spa re
whee l wel l. Store it in the luggage compart­
ment and secure it so that it does not slide
r=> page 59 .
.. Check the tire pres sure on the spare wheel
immediately after mounting it .
.. As soon as possible, have the
tightening
t o rqu es
on a ll wheel bolts checked with a
torque wrench . The correct tightening tor­
que is 90 ft lb ( 120 Nm) .
.. Have the flat tire
re pl ac ed as soon as possi­
ble.
(D Tips
- If you notice that the whee l bolts are
corroded and difficult to t urn w hile
changing a tire, they should be replaced
before you check the tightening torque .
- Drive at reduced speed until you have the
tightening torques checked .
- After changing a wheel, the tire pressure
in a ll four tires must be checked/cor rect­
ed and the tire pressure monitoring indi­
cator must be stored in the MMI
r=> page 251.
Decorative wheel covers
App lies to vehicles: with deco rat ive wheel cove rs
T h e decorativ e whe el covers must b e re moved
firs t to access the wheel bol ts.
Fi g. 186 Ch ang ing a w hee l: Remov ing the wheel cove r
Removing
.. Insert the hook (provided with the vehicle
tool kit) in the hole in the wheel hub cover .
.. Pu ll off the
dec orativ e whe el c over
r=> fig . 186.
What do I d o now ? 255
Wheels with wheel bolt caps
Applies to vehicles: wit h wheel bo lts with caps
T he cops must be removed first from the
wheel bolts before the bolts con be un­
screwed .
Fig . 1 87 Changin g a whee l: r emovi ng th e wheel bolt
c ap s
Removing
.. Push the pla stic clip (provided with the ve­
hicle tool kit) over the wheel bolt cap unt il
the inner reta iners on the clip align with the
edge of the cove r.
.. Remove the cap w it h the
pl as tic clip (veh i­
cle too l kit)
r::!:> fig . 187.
Refitting
.. Place the caps over the wheel bolts and
push them back on.
The caps are to protect and keep the wheel bolts clean.
Loosening and tightening the wheel
bolts
The wheel bolts must be loosened before rais­
ing the vehicle .
Fig. 188 Changing a whee l: loosening t he w hee l bo lts ..

a firm base for the jack on the ground. If nec­
essary place a sturdy board or similar support
under the jack. On
hard, slippery surfaces
(such as tiles) use a rubber mat or sim ilar to
prevent the jack from slipping¢ .&.
A WARNING
-You or your passengers could be injured
wh ile chang ing a wheel if you do not fol­
low these safety precautions:
- Positioning the jack under the vehicle
at any other place than those indicated
above may damage the vehicle or may
result in personal injuries.
-A soft or unstab le surface under the
jack may cause the vehicle to slip off the jack. Always provide a firm base for
the jack on the ground. If necessary, use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Pa ssenge rs must not remain in the
ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to
raise the jack .
- Changes in temperature or load can af­
fect the height of the vehicle .
What do I do now? 257
Taking the wheel off /installing the spare
Follow these instructions step-by-step for
changing the wheel.
F ig . 191 Changing a wheel: u sin g the screwd river han­
dle (with the blade removed) to turn the bolts
Fig. 192 Changing a whee l: alignment pin inside the
top ho le
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.., Use the hexagonal socket in the screwdriv­
er handle
to completely remove the top·
most wheel bolt and set it aside on a
clean
surface ¢fig. 191.
.., Screw the threaded end of the alignment
pin
from the tool kit hand-t ight into the
empty bolt hole
¢fig. 192 .
.., Then remove the other wheel bolts as de­
scribed above .
.., Take off the wheel leaving the alignment
pin in the bolt hole ¢(D.
Putting on the spare wheel
.., Lift the spare wheel and carefully slide it
over the alignment pin to guide it in place
¢(D.

258 What do I do no w?
• Use the hexagonal socket in the screwdriver
hand le to screw in and tighten all wheel
bolts
slightly .
• Remove the alignment pin and insert and
t ighten the remaining wheel bolt slightly
Like the rest .
• Turn the jack handle counter-clockw ise to
lower the vehicle unt il the jack is fully re­
leased .
• Use the whee l bolt wrench to t ighten al l
wheel bolts firmly¢
page 255 . Tighten
them
crosswise, from one bolt to the (ap­
proximate ly) opposite one, to keep the
whee l centered.
@ Note
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you.
@ Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or tighten
the wheel bolts .
- Pull the reversible b lade from the screw­
driver before you use the hexagonal
socket in the handle to turn the whee l
bo lts.
- When mounting tires with
unid irectional
t re ad design
make sure the tread pat­
tern is pointed the right way
~ page 258.
- The wheel bolts should be clean and easy
to turn . Check for d irt and corrosion on
the mat ing surfaces of both the whee l
and the hub. Remove all dirt from these
s ur faces before remo unt ing the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a sp are t ire w ith a tre ad pattern
intended for use in a specific direction
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection , please
note the following :
- The direct ion of rotation is marked by an ar­
row on the side of the ti re .
- If the spare tire has to be installed in the in­
correct direct ion, use the spare tire only
temporarily s ince the tire will not be able to
achieve its optim um performance cha racter­
is tic s wit h regard to aquap la ni ng, no ise and
wear .
- We recommend that you pay part icu la r at­
t en tion to th is fact d uring wet wea ther and
t ha t you adjust you r speed to match road
conditions .
- Replace the fl at tir e with a new o ne an d
have it insta lled on you r vehicle as soon as
possible to restore the handling advantages
of a u nidirectional tire .
Notes on wheel changing
Please read the information ¢ page 242, New
tires and replacing tires and wheels
if you a re
going to use a spare tire which is different
from the ti res on your vehicle .
After you change a tire:
- Check the tire pre ssure on the spare imme­
diately after install ation.
- Have th e whe el bolt tight ening torqu e
c hecked with a torque wrench as soon a s
possible by your author ized Audi dealer or
a qualified service stat ion.
- With steel and alloy wheel rims, the wheel
bolt s are cor re ctl y tightened at a torque of
90 ft lb (120 Nm ).
- If you noti ce that the wheel bolts are cor­
roded and diffi cult to turn while changing
a ti re , they should be replaced before you
check the t ightening torque. .,..

2 70 General information
General information
Explanation of
technical data
Some of the technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
r:::>page 27 2. This sec ·
tion provides general information, notes and restrictions which apply to this data .
Vehicle identification
The key data is given on the vehicle identifica·
tion number (VIN) plate and the vehicle data
sticker.
Fig. 206 Veh icle Ide ntific atio n Number (VlN) p late: lo­
cation on driver 's sid e das h panel
Fig. 207 Th e vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
b le from the outside through the windshield
r:::> fig . 206. You can also display the Vehicle
Identification Number of your vehicle in the
MMI. Select: Function button
ICAR ! > Car sys­
tems
> VIN number . The
vehicle identification label
is located in the luggage compartment in the
spare wheel wel l.
The label¢
fig. 207 shows the following vehi­
cle data :
(D Production control No .
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo·
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War·
ranty
& Maintenance booklet.
The safety compliance sticker
is you r assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
time the vehicle was manufactured . You can
find this sticker on the left door jamb.
It
shows the month and year of production and
the ve hicle ident ification number of your vehi ·
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carr ier .
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are Listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oi l and coolant, plus maximum load, wh ich in·
eludes passenger weight (lSO lbs/68 kg per
Ill>

Side assist Activating and deactivating . . . . . . . . . . . 88
Cleaning sensors ............ ... .. . 202
Description . ............. .... .. .... 88
Informational and alert stage signals .. 90
Messages in instrument cluster display . 94
MMI settings .... .. ...... .. .. .. .. .. 93
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 89
Safety tips . . . . . . . . . . . . . . . . . . . . . . . . 94
Sensor detection area . . . . . . . . . . . . . . . 89
Side curtain airbags ........... .... .. 160
Description .... .. .. ...... .. .. .. .. . 160
How they work .............. ... ... 161
Safety instructions ........ .. .. .. .. . 161
Side marker lights ......... .. .. .. .. .. 41
Ski sack ..... .. ................ ..... 62
also refer to Trunk pass-through .. .. .. 63
Sliding/tilting sunroof Emergency closing .......... .. .. .. .. 40
Opening and closing ...... .. .. .. .. .. 39
Snow chains . ................ ... ... 247
Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Sources of information about child re-
straints and their use ....... .. .. .. .. . 181
Space-saving spare tire ...... .. .. .. .. . 253
Spare tire .... ................ ... ... 253
Speedometer . . . . . . . . . . . . . . . . . . . . . . . 25
Speed rating letter code ..... .. .. .. .. . 243
Speed warning system ...... .. .. .. .. .. 76
Star button . . . . . . . . . . . . . . . . . . . . . . . . . 23
START ENGINE STOP button ........... 71
Starting from rest .......... .. .. .. .. .. 75
Startingoffwithatrailer .... .. .. .. .. .. 75
Starting the engine .................. 71
Steering Electrically adjustable steering wheel .. 70
Manually adjustable steering wheel .. .. 70
also refer to Electro-mechanical power
assist ..... .. ................ .... 189
Steering wheel Easy entry feature . . . . . . . . . . . . . . . . . . 71
Indicator light . . . . . . . . . . . . . . . . . . . . . 17
Steering wheel heating .... .. .. .. .. .. 69
Steering wheel column Adjusting electrically ...... .. .. .. .. .. 70
Adjusting manually ....... .. .. .. .. .. 70
Steps for determining correct load limit . 239
Index 287
Stopping the engine . ............... .. 73
Storage . . . . . . . . . . . . . . . . . . . . . . . . 55, 60
Sunroof .... .. .. .. ... ............ ... 39
Sun shade .. .. .. .. ................. . 45
Sun visors ........ .. ................ 45
Symbols
refer to Warning/indicator lights ..... . 11
T
Tachometer . . . . . . . . . . . . . . . . . . . . . 11, 22
Technical modifications .............. 276
Temperature display ............. .. .. . 22
T ether anchors . . . . . . . . . . . . . . . . . . . . . 180
Tether strap . . . . . . . . . . . . . . . . . . . . . . . 180
The first 1,000 miles (1,500 km) and after-
wards ...... .. .. .. ................. 192
Three-zone climate control . . . . . . . . . . . . 65
Tie-downs . . . . . . . . . . . . . . . . . . . . . 61, 125
Tips for the environment
Saving fuel . ... .. .. ................ 58
tiptronic ... .. .. .. ................. 102
A ut omatic Shift Lock (ASL) ...... .. .. 104
Driving .......................... 102
Dynamic shift program ............. 105
Emergency mode ... ............... 106
Kick-down . .. .. .. ................. 104
Manual shift program .............. 105
Selector lever .. .. ... ... ...... ..... 103
Tire pressure . ...................... 23 7
Tire pressure monitoring system ....... 249
Loss of air pressure ................ 250
Malfunction . .. .. ................. 250
Resetting tire pressures ............ . 251
Tires ...... ... .. .... .......... ..... 231
Service life ....... ................ 241
Speed rating letter code ........ .. .. 243
Tire manufacturing date ........ .. .. 243
Tire specifications ................ . 243
Tread depth ....... ............... 241
Uniform tire quality grading ........ . 245
Winter tires . .. ...... ............. 246
T ires and vehicle load limits ....... .... 239
Tires and wheels Checking tire pressure ............. . 237
Cold tire inflation pressure ......... . 235
Dimensions .. .. .. ................. 242
•
•