
12  Instrum ent s and  w arn ing /indic ato r  light s 
-Never open the  engine  hood  if  you see or 
hear steam,  or  if  you see engine  coolant 
dripping  from  the  engine  compartment. 
You could  burn yourself . Let the  engine 
cool off  first  so that  you cannot  hear or 
see any steam  or  engine  coolant . 
@ Note 
-Mounting  additional  lights  or  accessories 
i n front  of  the  a ir inlets  reduces the  cool
i ng effect  of  the  rad iator . At  h igh outside 
temperatures  or  high  eng ine load,  the 
engine  could  overheat. 
- The front  spo iler  has been designed  to 
proper ly distribute  the  cooling  air when 
t h e ve hicle is moving. 
If the  spoiler  is 
dam aged,  th is co uld  red uce the  cooling 
effect  and the  engine  co uld  then  over
heat . Ask your  authorized  Audi  dea ler for 
assistance . 
Tachometer  (engine  rev counter) 
The tachometer  indicates  the  engine RPM 
(revolutions  per  minutes). 
If engine  RP M drops be low  1,500,  yo u should 
downshift  to  the  next  lower  gear.  The red a rea 
at  the  end of  the  sca le indicates  maximum 
perm iss ib le engine  RPM after  the  break-in  pe
riod.  Before  reaching this  area, move these
lector  lever to  position  "D/S  (Drive)"  or  ease 
your  foot  off  the  accelerator  pedal. 
(D Note 
The tachometer  needle  should  on ly br iefly 
be in  the  red zone: you  could  damage your 
engine!  The beginn ing of  the  red zone var
ies depending  on the  engine . 
@ For the  sake of the  environment 
Upshifting early saves fuel  and  reduces en
gine  noise. 
Fuel gauge 
The fuel  gauge  only works  when  the  ignition  is 
on . 
If the  fuel  level  d rops below  2 . 6 ga llons  (10  liters),  the  bottom  LED turns  red and the 
indicator 
light~ turns  on  ¢ 
page  21. The 
bottom  LED blinks  red when  the  fuel  level  is 
very  low. 
T he possible  range based on the  current  fuel 
level  is shown  in  tab@¢ 
page  23,  fig . 4 . 
(D Note 
Never run  the tank  completely  dry.  An ir 
r egular  supply  of  f uel  can cause engine 
misfiring  and fuel  could  enter  the  ex ha ust 
system . The catalytic  converter  could  then 
overheat  and  be damaged. 
Warning/indicator  Lights 
Description 
The ind icator  lights  in the  instrument  cluster 
blink  or  turn  on. They indicate  funct ions or 
malfunctions ¢,& . 
Messages may appear with  some indicato r 
lights.  A warning  signal will  sound at the 
same t ime. The  indicator  lights  and  messages 
in the  center  of  the  displays  may be rep laced 
by other  d isplays . To show them  again,  select 
the  tab  for  ind icator  lights  and  messages us
i ng the  multifunction  steering  wheel 
¢ 
page  23. If t here are several malfunc
t ions, you  can display  them  one at  a time  us
ing the  thumbwheel. 
Some  indicato rs lights  in the  d isplay can turn 
on  in severa l co lors. 
A WARNING 
- F ailure  to heed w arning  l igh ts and other 
important  vehicle  in forma tion  may res ult 
in ser io us personal  inj ury or vehicle  dam
age . 
- Whenever  stalled  or  stopped  for  repair,  move the  vehicle  a safe d istance  off  the 
road, stop  the  engine,  and turn  on the 
emergency  flasher¢ 
page  42. 
-The engine  compartment  of  any motor 
veh icle is a potentially  hazardous  area. 
Before you chec k anything  in the  engine  

Instrument s and  warnin g/indic ator  ligh ts 13 
compartment,  stop  the  engine  and let  it 
cool  down.  Always exercise extreme  cau
t ion when working  under the  hood 
<=> page  214,  Engine  compartment 
@ Tips 
Ma lf u nctions  or faults  wi ll be identified  ei
ther  with  a red symbo l (pr iority  1  -Dan
ger!)  or  with  a yellow  symbol  (pr iority  2  -
Warn ing). 
Overview 
Some ind icator  lights  turn  on  briefly  to  check 
the  function  of  that  system  when you switch 
the  ignition  on.  These systems  are ma rked 
with  an./  in the  fo llow ing tab les. If  one of 
these  indicator  lights  does not  turn  on,  there  is a malfunction  in that  system. 
Red  indicator  lights 
Red symbols  indicate  a prio rity  malfunction  -
D anger! 
- Pull  off  the  road. 
- Stop the  vehicle. 
-Turn  off  the  engine. 
- Check the  ma lf u nctioning  system . Contact 
your  authorized  Audi  dea ler or  a qualified 
workshop  for  assistance. 
USA mode ls: 
Brake ma lf u nction./ 
c::>page  14 
Canada models: 
Brake malfunction./ 
c::>page 14 
- USA models: 
----
Electromechanical  parking  brake 
<=> page  16 
Canada models: 
Electromechanical  parking  brake 
<=>page 16 
Engine cooling  system 
<=>page  16 
Engine  oil  pressure 
<=>page 17 
I 
Engine oil  level 
Q page  18 
Battery 
Qpage  17 
Safe ty belt 
Q page  17 
Electromechanical  steering  ./ 
<=>page 193 
Electronic steering  column  lock 
Qpage  18 
Engine start  system 
Qpage 18 
Speed wa rning  system 
Qpage 76 
Adaptive  cruise control./ 
Qpage  80 
---Pedestrian warn ing 
Qpage97 
Yellow  indicator  lights 
Ye llow symbo ls indicate  a priority  2  malfunc 
tion  - Warning! 
I 
USA models: Safety systems 
Q page  18 • 
m 
Canada models : Safety systems 
Qpage 18 
Ji] 
Ele ctronic  Sta bilizat ion Prog ram 
( E SP)./ 
Q page  19 
I 
Electronic  Stabilization  Program 
(ESP) ./ 
Qpage  19 
rm 
USA models: 
Anti-lock  braking  system  (ABS) 
defective  ./ 
c::> page  19 
--
E 
Canada models: 
Anti-lock  braking  system  (ABS) 
defective  ./ 
<=>page 19 
l 
I  

14  Instrum ent s and  w arn ing /indic ato r  light s 
ll 
Worn  brake pads 
¢ page20 
• 
Electromechanical  parking  brake 
¢page  73 
g 
Tire pressure monitoring  system 
./ 
¢page253 
11111 Tire pressure monitoring  system 
¢page253 
rm 
Electronic  power  control./ 
¢page20 
g 
Malfunction  indicator  Lamp (MIL) 
./ 
¢page20 
• 
Engine speed limitation 
¢page  21 
• 
Engine oil  level 
¢page  18 
• 
Engine o il sensor 
¢ page  21 
• 
Battery 
¢page  17 
~ 
Tank system 
¢page  21 
• 
Windshield  washer  fluid  level 
¢page  21 
m 
Windshie ld wipers 
¢ page  21 
--
I! 
Remote  control  key 
¢page  70 
I 
Remote  contro l key 
¢ page  72 
!! 
Battery  in remote  control  key 
¢page  31 
I:~ 
Defective light  bulb  warning 
¢ page  21 
I a 
Rear fog  light(s) 
¢page  21  Headlight  range control 
¢
page22 
adaptive  light * 
¢page22 
-
Light-/rain  sensor faulty 
¢page22 
Transmission 
- multitronic ® 
¢ page 106 
-tiptronic ® ¢page 111 
Electronic  steering  column  lock 
¢page  18 
Engine start  system 
<=>page 18 
Electromechanical  steering./ 
¢page  193 
Other  indicator  lights 
11!1 1!11 Turn signals 
m 111 <=>page22 
~ USA model s: Cruise control " 
~ <=> page  76 
ra 
I 
I 
• 
Canada  mod els: Cruise control* 
<=> page  76 
Adaptive  cruise control * 
<=>page  80 
Adaptive  cru ise cont ro l* 
¢ page80 
Adaptive  cruise control * 
¢page80 
H igh  beam 
¢page43 
BRAKE /( (f) ) Brake  system 
The light  i lluminates  when  the  ignition  is 
switched  on . It  goes o ut  after  the  engine  has 
been started.  This  indicates  that  the  brake 
warning  light  is functioning  properly . 
If  the  brake warn ing  light  does not  light  up 
when  the  engine  is cranking , there  may  be  a 
Ill- 

Instruments  and  warning/indicator  lights  17 
Follow  the  warning stickers¢ page  214, 
Engine compartment. 
@ Note 
Do  not  continue  driving if the . symbol 
illuminates.  There  is a  malfunction  in  the 
engine  cooling  system  -you  co uld damage 
your  eng ine. 
D Battery 
This  warning/indicator  light  detects  a mal 
function  in  the generator  or  in  the  vehicle's 
electrical  system. 
The . warning/indicator  light  illuminates 
when  you  switch  on  the  ignition and  must  go 
out  after  the  engine  has  started. 
•  Alternator  fault:  Battery is not  being 
charged 
If the  indicator  light turns  on  and  the  mes
sage  appears,  there  is  a  malfunction  in  the 
generator  or vehicle  e lectrica l system. 
Drive  to  you r authorized  Audi dealer  or  quali
fied  workshop  immediately.  Because  the vehi
cle  battery  is discharging,  turn  off  all  unnec
essary  electrical  equipment  such  as  the radio . 
Seek  professional  assistance  if the  battery 
charge  leve l is too  low. 
(•i Low battery  charge : battery  will  be 
charged  while driving 
If the  indicator  light  turns  on and  the  mes
sage  appears,  there  may  be  limited  star ting 
ability. 
I f  this  message  turns  off  after  a  litt le wh ile, 
the  battery  charged  enough  wh ile  driving. 
If  the  message  does not turn  off,  have  your 
author ized  Audi  dealer  or  qualif ied  workshop 
correct  the  malfunction. 
~ Safety  belts 
This warning/indicator  light  reminds you  to 
put  on your  safety  belt. 
The . warning/indicator  light  illuminates 
when  the  ignition  is switched  on  to  remind 
the  driver  and  any  front  passenger  to  put  on 
the  safety  belt.  Additionally,  an  acoustic  warn
ing  (gong)  wi ll also  sound. 
For  more  Information¢ 
page  133, i Safety 
belt  warning  light. 
~ Engine  oil  pressure  malfunction 
The red engine oil pressure  warning  symbol 
requires  immediate  service or  repair . Driving 
with  a  low-oil-pressure  indication  is likely  to 
inflict  severe damage  to  the  engine  . 
• Switch  off  engine  and check  oil  level 
If  the  indicator  light turns  on  the  message  ap
pears,  the  oil  pressure is too low. 
""  Pull  off  the  road  . 
...  Stop  the  vehicle. 
...  Tur n  off  the  engine . 
"" Check  the  engine  oil  level¢ page  225. 
"" If  the  eng ine  oil  level  is  too  low,  add  eng ine 
oil ¢ 
page  225. Make sure  that  the  oil  pres
sure  warning  symbol. appears  no longer 
in  the  display  before  you  start  dr iv ing  again . 
""  If the  engine  oil level  is  correct  and  the  indi 
cator  light  still  turns  on,  turn  the  engine off 
and  do  not continue  driving.  Seek  professio
na l assistance . 
(D Tips 
-The engine  oil  pressure  symbol. is 
not  an indicator  for a  low engine  oil  lev
el.  Do not  rely  on it. Instead,  check the 
oil  level  in your  engine  at  regular  inter
vals,  preferably  each  time  you  refuel , 
and always  before  going  on  a long  trip. 
- The yellow  oil  level  warning  indication 
II requires  oil  refill or workshop  serv
ice without  delay.  Do not  wait  until  the 
red oil  pressure warning . starts  to 
flash  before  you respond  to  the  low  oil  ..,  

18  Instruments  and  warning/indicator  lights 
level  warning 11!1. By then,  your engine 
may already  have suffered  serious  dam· 
age . 
~ Engine  oil  level 
•  WARNING: Please  add oil  immediately 
When  the  symbo l an d the  driver message  ap
pear, the  oil  has to  be  replenished  r ight  now 
co  page 222. 
If  th e  indica tor  light  and  the  message  appear, 
a d d engine  oil immed iate ly 
co  page 225. 
Ill Add oil,  max . x qt (l). You may continue 
driving 
W hen the  symbol  and  the  dr ive r message  ap
pear, add  t he amo unt  of o il appearing  in the 
d is pl ay a t the  next  opport unit y 
co  page 222 . 
~- Steering  column  lock 
•  Do not  drive  vehicle:  Steering  defective 
If t he  indicator  light tu rns on and  t he  mes
sage  a ppears,  t he re  is an  ele ct ro nic  steer ing 
col um n lo ck ma lf u nction.  You c annot  sw itch 
the  ign ition  on. 
D o 
not tow your vehicle because  i t ca nnot  be 
s teered.  Seek professional  ass istance. 
1!!11 Steering  lock : system  fault . Please  con
tact  dealer 
If the  indicator  light t urns on and  t he  mes
sage  appears , th ere  is an  elect ronic steer ing 
column  lock ma lfunction . 
Drive to  yo ur autho rized Aud i dea le r i mmedi
ately  to  have the  mal function  corrected. 
A WARNING 
Your vehicle must  not  be towed  in the 
event  of a  malfunct io n  in the  electron ic 
s te eri ng colum n loc k because  i t cannot  b e 
s teer ed du e to t he  locked s teering . If it is 
to wed w ith  the s tee ring lo cked,  there  is 
t he  ri sk of  an  accide nt. 
© -Engine  start  system 
•  Engine  start  system  fault.  Please  con
tact  dealer 
If th e indicato r ligh t turns  on and  the  mes 
sage  app ears,  do 
not switch the  ig nitio n  off 
be cause you may no t  be a ble to sw itch  i t on 
ag ain . 
D rive  to your authorized  A udi dealer  i mmed i
ate ly to  have th e ma lfu nction  corr ected . 
II! Engine start  system  fault.  Please  con 
tact  dealer 
If the  indicato r light  turns  on and  the  mes 
sage  appears,  there  is a  malfunct ion  in the  en
gine sta rt system. 
Drive to your authorized  A udi dealer  immedi 
ate ly to  have the  ma lfunction  corrected. 
~ii !i: Safety  systems 
The fl (USA models)/ E,i (Canada models)  in
dicator  light  mo nitors  the  sa fety systems  e.g. 
airbags , pretensione rs and  illuminates  fo r a 
f e w s econds  each time  you switch the  ign it io n 
o n . 
If the 
fl (USA models)/ E,i (Canada mode ls) 
i ndicato r light  does  not  go o ut,  or  if it illum i
na tes whil e you are  driving, o r if it s tarts  to 
blink, then  there  is a malfu nctio n so mewhe re 
i n t he  sys te m . 
If the  light  does  no t  illumina te 
whe n you swi tch the  ig nitio n  on,  this also 
mea ns  there  is a  mal funct ion . 
A WARNING ~ 
If yo u have a ma lf un ction  in t he safety  sy s-
tems , contact  you r authorized  Audi dea le r 
i mmediately.  Othe rwise the  safety  sys
tems  may not  work pr operly in an  acc i
dent.  

Instruments  and  warning/indicator  lights  21 
!?i Engine  speed  limitation 
A ppl ies to  vehicles: wit h en gin e s pee d l im itat ion 
(II Engine speed maximum  XXXX RPM 
The  engine  speed  is automatically  limited  to 
the  speed  displayed  in  the driver  information 
system.  This  protects  the  engine  from  over heating. 
The  engine  speed  limitation  deactivates  once 
the  engine  is no  longer  in the  critical  tempera
ture  range  and  you  have  released  the  accelera
tor  pedal  once. 
If  the  engine  speed  limitation  was  activated  by an  engine  control  malfunction,  the  indica
tor  light~  also  turns  on.  Make  sure  that  the 
speed  does  not  go  above  the speed  displayed. 
Drive to  your  authorized  Audi dealer  immedi
ately  to  have  the  malfunction  corrected. 
~ . Engine  oil  level 
II Add oil,  max.  x qt  (l).  You may continue 
driving 
When  the symbol Ill and  driver  message  ap
pear,  add  the  amount of  oil appearing  in the 
display  at  the  next  opportunity ¢ 
page 225. 
~ .... Engine  oil  sensor 
II Oil  level! Sensor defective 
If  the  symbol  illuminates,  contact  your  au
thorized  Audi  dealer  and  have  the  oil sensor  inspected.  Until  you  have  this  done,  check  the 
oil  level  each  time  you  refuel  just to  be  on  the 
safe  side¢ 
page 225. 
Bil Fuel  level  indicator 
Ii Please refuel 
If the  indicator  light  turns  on  for  the  first 
time  and  the  message  appears,  there  are 
about  2.6  gallons  (10  liters)  of  fuel  left  in the 
tank . Time  to  refuel 
¢ page 216. 
Ii Tank system malfunction!  Contact dealer 
If  the  indicator  light turns  on  and  this mes
sage  appears,  there  is a  malfunction  in the 
tank  system. 
Drive to  your  authorized  Audi dealer  immedi
ately  to have  the malfunction  corrected. 
C> Windshield  washer  fluid  level 
II Please refill  washer fluid 
If the symbol  illuminates,  add  windshield 
washer  fluid to  the  washer  system/headlight 
washer  system*  ¢ 
page 234. 
~ Windshield  wipers 
rlJ Windshield  wiper  defective 
There  is a malfunction  with  the windshield 
wipers. 
Drive to  your  authorized  Audi dealer  immedi
ately  to have  the  malfunction  corrected. 
~/0$ Defective  light  bulb  warning 
f'a-If  the  indicator  light  turns  on,  a  bulb  has 
failed.  The  message  indicates  the  location of 
the  bulb. 
IJ-if a  rear  fog  lamp  has  failed,  the  indicator 
light  turns  on  to  indicate  the  location on the 
vehicle. 
Vehicle lights:  malfunction 
If  the  message  appears,  there  is a  malfunc 
tion  in the  headlights  or  light switch . 
Drive to  your  authorized  Audi dealer  immedi
ately  to  have  the  malfunction  corrected. 
A WARNING 
- Light  bulbs  are  pressurized  and  could  ex
plode  while  they  are  being  changed  caus
ing  serious  personal  injury. 
- Work  with due care  when  handling  the 
high-voltage  section  of  gas  discharge 
(xenon)  lights.  Failure  to  do  so could  re
sult  in  death  or  serious  injury.  

By pressing  the I START ENGINE STOPI button 
without  depressing  the  brake peda l, the  igni
tion  is on and switched 
off by pressing  it 
again. 
After  a cold  engine  is started,  the re may be a 
brief  period  of  increased  noise because oil 
pressure must  first  bui ld up in the  hydraulic 
va lve adjusters.  This  is normal  and  not  a cause 
for  concern. 
If  the  engine  should  not  start  immediately, 
the  starting  process  is automatically  stopped 
after  a short  time.  Repeat starting  procedure. 
Driv er m essag e  in th e in strument  clu ste r 
disp lay 
Pr ess  br ak e p ed al to  start  engin e 
This message appears  if  you press the 
I START ENGINE STOP ! button  to  start  the  en 
g ine and  do not  depress the  brake peda l. The 
engine  can on ly be started  if  the  brake pedal 
is depressed. 
!!I C o nv enience ke y: I s ke y not  in th e vehi
cle ? 
This message appea rs a long  with  the !!I sym
bol  if  the  maste r key is  removed from  the  ve
hicle with  the  engine  r unning . It  is intended 
to  remind  you  (e .g . when  changing  drivers) 
not  to  continue  the journey  witho ut  the  mas
ter  key. 
I f  the  master  key is no longer  in the  vehicle, 
you  cannot  sw itch  on the  ignition  after  stop
ping  the  engine  and yo u also cannot  start  the 
engine  again.  Moreover, you  cannot  lock the 
veh icle from  the  outside  with  the  key. 
Shift  to  P , other wis e  vehicle c an roll  away. 
Doo rs do not  lock if le ver i s not  in P. 
This message appears for  sa fety  reasons 
a long with  an audib le warning  tone  if  the 
P 
selector  lever  position  is not  engaged when 
stopping  the  eng ine with  the 
I STAR T ENGINE STOP ! button.  Select the P se
lector  lever posit ion.  Otherwise  the  veh icle 
could  roll  and it  can not  be  locked . 
On  th e ro ad  71 
Ke y not  r ecogni sed . Hold  bac k of ke y again st 
ma rked area.  See owne r's  manual. 
If  the  indica tor  l ight  turns  on and this  mes
sage appears, there  is a malf unct ion 
¢ page 72. 
Steering  lock 
The steering  locks when  you turn  the  engine 
off using the I START ENGINE STOP ! button 
and  open the  d river's  doo r.  T he locked  steer 
i ng helps  p revent vehicle  theft. 
& WARNING ~ 
- Never allow  the  engine to  run  in confined 
spaces  -danger  of  asphyxiation . 
- Never turn 
off the  engine  un til  the  vehi
cle has come to  a complete  stop . 
- The brake booster  and power  steering 
only  work  when  the  eng ine is r unning . If 
the  engine  is 
off, you  have to  use more 
force  when  steering  or  braking.  Because 
you  cannot  steer  and brake as you  usual ly would,  this  cou ld  lead to  crashes and 
serious injuries. 
(CT) Note 
- Avo id  h igh engine  rpm,  full  thrott le and 
heavy engine  loads until  the  engine  has 
reached operating  temperature  -other
w ise you  risk engine  damage . 
- The engine  cannot  be started  by pushing 
or towing  the  vehicle. 
- If  the  engine  has been under  heavy load 
for  an extended  per iod,  heat  builds  up  in 
the  engine  compa rtment  afte r the  e n
gine  is switched 
off  -there  is a  risk of 
damaging  the  engine.  Allow  the  engine 
to  run  at  idle  fo r about  2  minutes  before 
switching  it 
off. 
(D Tips 
- If  you  open the  d river 's doo r with  the  ig
nition  on,  a buz ze r sounds  and the  mes
sage 
Ignition  i s on appears in the  instr u
ment  cl uste r display . Sw itch  the  ignition 
off . Ill- 

192  Intelligent  technology 
freezing  conditions ice) on the  brake pads. A 
few  careful  brake applications  should  dry  off 
the  brake pads or  remove  any ice coatings. 
The effectiveness  of  the  brakes can be reduced 
when the  vehicle  is driven  on a salt-covered 
road and the  brakes are not  used . Here too 
, 
you  should  clean  off accumulated  salt  coating 
from  brake discs  and pads with  a few  careful 
applications  of  the  brake 
Q & . 
Corrosion 
There may be a tendency  for  dirt  to  build  up 
on the  brake pads and corrosion  to  form  on 
the  discs if  the  car is not  driven  regularly  or 
only  for  short  trips  with  little  use of  the brakes. 
If  the  brakes are not  used frequently,  or  if  cor
rosion  has formed  on the  discs, it  is advisable 
to  clean  off the  pads and discs by braking 
f irmly  a few  times  from  a moderately  high 
speed 
Q & . 
Faults  in the  brake system 
If you should  notice  a  sudden increase in 
brake pedal  travel,  then  one of  the  two  brake 
circuits  may have failed 
Q & . 
Low brake fluid  level 
Malfunctions  can occur in the  brake system  if 
the  brake fluid  level is too  low. The brake fluid 
level  is monitored  electronically. 
Brake booster 
The brake booster  works  with  vacuum  pres
sure which  is created  only  when the  engine  is 
running 
Q & . 
Brake lining  wear  status 
Brake  lining  wear  may be checked by visual  in
spection  of  the  condition of the  brake pads 
through  the  openings  in  the wheel.  If neces
sary, the  wheel  may be removed  for  this  in
spection 
Q page  258,  Changing  a wheel. 
WARNING 
- You should  perform  braking  maneuvers 
for  the  purpose  of  cleaning  the  brake  system  only  if  road conditions  permit. 
Other  road  users must  not  be put  at  risk -
you  may cause an accident! 
- Before descending  a steep  grade,  reduce 
speed and shift  transmission  into a lower 
gear or  lower driving  range.  Do not  ride 
the  brakes or  hold  the pedal down  too 
long  or too  often . This could  cause the 
brakes to  get  hot  and diminish  braking 
efficiency. 
- Do not  "ride  the  brakes"  by resting  your 
foot  on  the pedal when you  do  not  intend 
to  brake. This may cause the  brakes to 
overheat,  premature  wear  and  increased 
stopping  distance. 
- Under certain  climatic  and operating 
conditions  such as passing through  wa
ter,  driving  in  heavy  rain or  after  washing 
the  vehicle,  the  effectiveness  of  the  brakes can be reduced.  In  winter,  ice can 
accumulate  on the  brake pads, linings, 
discs and drums.  Carefully  apply  brakes 
for  a test.  Brakes will  dry  and ice coat
ings will  be cleaned  off after  a few  care
ful  brake applications. 
- Driving  for  an extended  period  of  time  on 
salt-covered  roads without  using your  brakes  can also  affect  braking  efficiency. 
Clean  off accumulated  salt coating  from 
brake discs  and pads with  a few  careful 
brake applications. 
- If you damage the  front  spoiler,  or  if you 
install  a different  spoiler,  be sure the  air 
flow  to  the  front  brakes is not  obstruct
ed. Otherwise  the  brake system  could 
overheat  reducing  the  effectiveness  of 
the  entire  brake system. 
- Failure of  one  brake circuit  will  impair 
the  braking  capability  resulting  in an  in
creased stopping  distance.  Avoid driving 
the  vehicle  and  have it  towed  to  the  near
est Audi  dealer  or  qualified  workshop. 
- Never let  the  vehicle  roll  to  a stop  with 
the  engine  shut  off. 
- If  the  brake booster  is not  working,  for 
example  when  towing  your  vehicle,  or 
because  the brake booster  has somehow 
been  damaged,  the  brake pedal  must  be 
~