2012 AUDI S3 winter tires

32 Driver information display
8.18, (Canada models) Speed warning 2
Storing warning 2 is recommended if you al­
ways
want to be reminded of a certain speed,
for example when you are traveling in a coun­
try that has a general maximum speed limit,
or if you do not want to exceed a specified
speed for winter tires.
The speed warning 2 symbol ,
[I/ [9] (Canada
models) appears in the display when you ex­
ceed the stored speed limit. Unlike warning 1, it will not go out until the vehicle speed drops
below the stored speed limit .
Setting speed warning 2
¢ pag e 32.
@ Tips
Even though your vehicle is equipped with
a speed warning system, you shou ld still
watch the speedometer to make sure you
are not driving faster than the speed limit.
Speed warning 1: setting a speed limit
Warning threshold 1 is set by the button.
Fig. 23 Sectio n of inst rume nt cl uste r: Set/Check but­
to n
Storing the maximum speed
11o-Drive at the desired maximum speed.
11o-Press the knob button ¢ fig. 23 until the
q page 31, fig. 22 symbol appears.
Resetting the maximum speed
.. Drive the vehicle at a speed of at least
3 mph (S km/h)
11o-Press the knob for more than 2 seconds.
The speed warning symbol
[I (USA models)/
ISl (Canada models) will appear briefly in the
d isplay when you release the button to indi- cate that
the maximum speed has been stored
successfully .
T he maximum speed remains stored until it is
changed by pressing the button again briefly
or until it is deleted by a lengthy push on the
button.
Speed warning 2: setting a speed limit
Switches in the wiper arm ore used to operate
warning threshold
2.
Fig. 24 W ipe r leve r: Trip compute r co ntrols
To store maximum speed
.. Turn off the ignition .
11o-Briefly press the button in the instrument
cluster ¢
page 32, fig . 23. The odometer
and the dig ital clock are now illuminated .
11o-Press the button for at least 2 seconds . The
current ly sto red max imum speed appears in
the display or the crossed out symbol for
warn ing thresho ld 2, if no maximum speed
was set previously .
.. Press the function selector switch in the
wiper
lever @qfig. 24 up or down to
change the set value. Va lues run up or down
in steps of 6.2 mph (10 km/h).
To delete maximum speed
.. Turn off the ignition.
.. Briefly press the button in the instrument
cluster ¢
page 32, fig. 23. The odometer
and the digital clock are now illuminated .
.. Press the button for at least 2 seconds. The
currently stored max imum speed appears in
the display .
II>

166 Intelligent technolog y
This is most noticeab le when turning the
steering whee l at low speeds (for examp le
when parking), -more effort will be re­
quired than usual.
- Be aware of the different than usual
steering response and adjust your steer­
i ng force accord ingly.
- Have the problem checked and set right
by an author ized Audi dealer as soon as
possible.
- If a steering malfunct ion occurs, this is
s ignaled with the
ts ~ or .• indicator
li ghts and a warning tone, see.
(D Tips
- If the power steering system shou ld fail,
or if the eng ine is not running (for exam­
ple, while being towed), you will st ill be
able to steer the veh icle. However, more
effort will be req uired to do so.
- If the power steering system is not func­
tioning properly, co ntact your authorized
A udi dealer immediate ly.
Driving with your
quattro ®
Appl ies to vehicles: with All Whee l Drive
With All Wheel Drive, all four wheels are driv ­
en.
General information
W ith All Whee l Dr ive, power is d istributed to
a ll fo ur wheels . This happens automa tic a lly
depending on your driv ing sty le and the road
conditions at the time . See also
¢ page 161.
Winter tires
When dr iv ing in the w inte r, your ve hicle w it h
A ll Whee l Drive has an advantage, even wi th
reg ular t ires. In win ter road condi tions it may
be adv isable to mo unt winter tires (o r all-sea ­
son tires) for improved driveability and b rak­
ing: these tires must be mounted on all four
wheels. See also ¢ page 22 7, Winter tires.
Snow chains
Where snow chains are manda to ry on ce rtain
roads, this norma lly also app lies to ve hicles
with all-wheel drive¢
page 228, Snow
chains.
Replacing wheels /tires
Vehicles with A ll Wheel D rive must a lways
have t ires o f the same s ize. A lso avoi d tires
with different t read depths . For deta ils see
page
¢ page 223, New tires and replacing
tires and wheels .
Off-Road driving?
Your Audi does no t have enough g round clea r­
ance to be used as an off-road vehicle .
It is
therefore bes t to avoid rough tracks a nd un ­
even terrain as much as possib le . Also refer to
¢ page 171.
A WARNING
-
Always ad just your dr iv ing to road and traf-
f ic conditions. Do not let the extra safety
afforded by the all-wheel dr ive tempt you
i nto ta king extra risks.
- Although the quattro ®all-wheel dr ive is
very effect ive, a lways remember that
b rak ing capac ity is limited by tire trac­
tion . You should therefore not d rive at
excessive speeds on icy or slippe ry road
sur faces.
- On wet road surfa ces, be careful not to
d rive too fast because the front whee ls
could begin to slide on top of the water
(hydroplaning). If this sho uld occ ur, you
will have no warning from a s udden in ­
crease in eng ine speed as w it h a front­
wheel d rive veh icle. Always drive at
speeds which are adjusted to the road
conditions - risk of c rash!

182 Cleaning and protection
• Wipe the windows dry with a clean piece of
cloth or kitchen paper towel.
The best way to remove snow from w indows
and mir rors is to use a brush. Use a non -abra­
sive
pla stic ice scraper -better still, a spray
deicer -to remove
ic e from windows and mir­
rors.
The windows must not be cleaned with insect remover or wax since these can interfere with
the function of the windshield wiper blades (chatter).
O il, grease or silicone residue can be removed
with
glass cle aner or silicone remo ver. How­
ever, wax residue req uires the use of a specia l­
ly form ulated solvent. P lease contact your au­
thor ized Audi dealer for adv ice on safe prod­
ucts for wax removal.
Windows sho uld a lso be cleaned on the inside
at regular interva ls.
Never dry windows with the same chamois
that you use to dry painted s urfaces. Wax resi­
due on the chamois can impair vision thro ugh
the windows.
A WARNING
- The windshie ld m ust not be treated with
water-repellent materials. They can i n­
c rease glare under poor visib ility condi­
t ions such as wetness, darkness, o r whe n
the sun is low on the hori zon. In addi­
t io n, they ca n cause the wi ndshield wip ­
ers to chatter .
- Always read and heed all WARN INGS and
othe r inform ation
Qpage 178.
0 Note
- Never use warm or hot water to remove
s now and ice from windows a nd mirrors.
This cou ld cause the g lass to c ra ck .
- To prevent damage to the wi res of the
r ear defogger, do not place any adhesive
sticke rs o n the inside of t he rear w indow
ove r the wires.
- To he lp prevent d irt from s cratch ing the
window, always scrape i n a forwar d di- rec
tion -pushing the sc raper away from
you -never bac k and fort h.
Steel wheels
Applies to vehicles: with steel wheels (e .g. if refitted with
winter tires)
The wheels also have to be cleaned.
• Always include the hub caps and wheel rims
when wash ing your vehicle to remove road
dirt, sa lt sprays and brake dust .
If necessary, use a commercial whee l cleaner
to remove accumulated brake dust.
The wheel rims are easier to keep clean i f they
are regularly coated with liq uid wax.
Paint scra tches shou ld be touched up as soon
as possib le to prevent corrosion
¢ page 181,
Touch-up paint.
A WARNING .....__
- Moisture and ice on brakes may affect
brak ing eff ic iency-
q page 163, General
information . Test the brakes ca refully af­
ter each vehicle wash .
- Always read a nd heed a ll WARNINGS and
the information
q page 178.
Cast (light) alloy wheels
Applies to vehicles : with Cast alloy wheels
-
Cast (light) alloy wheels require special care.
• Wash the w heels with a sponge or hose
brush every other week .
• For deep cleaning afterwards, use on ly a
ded icated acid-free cast alloy wheel cleaner.
• Rub a coat of
liquid wa x onto the rims every
three month. Be sure to reach and treat all
parts of the rim .
To preserve the decorative appearance of the cast alloy w heels, some special care is neces ­
sary. In addition to road dirt and salt, brake dust is also co rrosive . If left on fo r too long,
brake d ust can cause pitting.
U se only spec ial
acid -free cleaners formulated
fo r alloy r ims . Safe products are ava ilab le at ..,_

214 Tires and wheels
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options weight
Maximum (permissible) inflation pressure
means the maximum cold inflation pressu re
to which a tire may be inflated. Also called
"maximum inflation p ressure."
Normal occupant weight
means 150 lbs. (68 kilograms) times the
number of occupants seated in the vehicle up
to the total seating capacity of your vehicle.
Occupant distribution means distribution of occupants in a vehicle .
Outer diameter means the overa ll diameter of an inf lated new
tire.
Overall width
means the linear distance between the exteri­
ors of the sidewalls of an inflated tire, includ­
ing e levations due to labeling, decorations, or
protective bands or ribs.
Ply
means a layer of rubber-coated parallel cords.
Production options weight
means the comb ined weight of those installed
regular production options weighing over 5
lbs . (2 .3 kg) in excess of those standard items
which they replace, not previously considered
in curb weight or accessory weight, including
heavy duty brakes, r ide leve lers, roof rack,
heavy duty battery, and specia l trim .
Radial ply tire
means a pneumatic tir e in which the p ly cords
that extend to the beads are laid at substan­
tially 90 degrees to the centerline of the
tread . Recommended inflation pressure
see
~
page 213, Cold tire inflation pressure.
Reinforced tire
means a t ire designed to operate at higher
loads and at higher inflation pressures than
the corresponding standard tire . Re inforced
t ir es my be identified as "XL", "xl", "EX TRA
LOAD", or "RF" on the sidewall.
Rim
means a metal support for a tire or a t ire and
tube assembly upon which the tire beads are seated.
Rim diameter
means nom inal d iameter of the bead seat. If
you change your wheel s ize, you w ill have to
purchase new tires to match the new r im di­
ameter .
Rim size designation
means rim diameter and width.
Rim width
means nominal distance between rim flanges .
Sidewall
means that portion of a tire between the
t read and bead.
Speed rating (letter code)
means the speed at which a tire is designed to
be driven for extended periods of time. The
ratings range from 93 mph (150 km/h) to
186 mph (298 km/h)
~ page 224 . You may
not find this information on all tires because
it is not requ ired by law.
The speed rating letter code, where applica­
ble, is molded on the tire sidewall and indi­
cates the max imum pe rmissibl e road speeds
~ A in Winter tires on page 228.
Tire pressure monitoring system*
means a system that detects when one or
more of a veh icle's tires are underinflated and
illuminates a low tire pressure warning tell­
tale.

224 Tire s and wheel s
handling when in good condition and properly
inflated
¢ .&..
We re commend that all wo rk on tires and
wheels be perfo rmed by an authorized A udi
deale r. T hey a re familiar with recommended
procedures and have the necessary special
too ls and spare parts as we ll as the proper fa ­
cilities for disposing of the old tires.
Authorized Audi dealers have the necessary
information about technica l requirements for
installing or changing tires and r ims .
Replacing t ires and whe els
Tires shou ld be rep laced at least in pairs and
not individua lly ( for examp le both front tires
or both rear tires together).
Be sure to read and heed the t ire pressure
monito ring system* info rmation
¢ page 230.
Always buy replacement radial tires that have
the same specifications as the tires approved
fo r your vehi cle by Aud i. Replacement t ires
must always have the s ame load rating speci­
f ication as the or ig inal equipment or approved
optional tires listed in the table
¢page 216.
Audi-approved specification t ires are specially
matc hed to you r vehicle and its lo ad limits,
and ca n contribute to the important road ho ld ­
ing, d riving characteristics, and safety of the
ve hicle . The table
(¢page 216) lists specifica ­
tions of the t ires approved for the Audi mod ­
e ls covered by your Owner's Literature.
The tire press ure label located either on driv­
e r's side B-p illar or inside the fue l filler flap
(¢ page 216 , fig. 168) lists the spec ificat ions
of the original equipment tires installed on
your ve hicle at the time it was manufactured.
F ederal law requires tire manufacturers to
p lace standard ized information on the s ide ­
wall of all tires¢
fig. 171. This information
ident ifies and describes the fundamental
characterist ics, the quality grade of the tire
and also provides a tire ident ificat ion number
for safety standard cert ificat ion and in case of
a recall.
Tire specification s
Knowledge o f ti re specifications ma kes it eas­
ier to choose the correct tires. Radial ti res
have the tire specifications marked on the
sidewa ll, for examp le:
P2 25 / 45 R 17 91H XL
Th is conta ins the following information:
P Indicates the tire is for passenger cars
(where app licab le)
2 25 Nom inal tire w idth in mm of the tire
from sidewall edge to sidewall edge. In general, the larger the number, the wider
the tire
45 Height/w idth ratio in percent (aspect ra-
t io)
R Tire construct ion: Radial
1 7 Rim diameter code (in inches)
91 Load rating code
H S peed ra ting letter code
XL (or "xl", "E XTRA LOAD" or "RF") in d ic ates
that the t i re is "Re info rced" or an "E xtra
Load" t ire
M+S (or "M/5") Indicate s that the ti re has
some mud and snow capabi lity
The tires could also have the information of
direction of rotat io n
¢ page 212.
Tire manufacturing d ate
The manufacturing date is also indicated on
the tire sidewall (possibly on ly on the
inner
s ide of the wheel):
"DOT ... 2211 ... "means, for examp le, that
the tire was produced in the 22nd week of 2011.
Sp eed rating (letter c ode )
The speed rating letter code on the whee ls in­
dicates the maximum permiss ible road speeds
¢ .&. in Winter tires on page 228.
P up to 93 mp h (150 km/h)
Q up to 99 mp h (1 58 km/h)
R up to 106 mph ( 170 km/h)
S up to 110 mph ( 180 km/h)
T up to 118 mph (190 km/h) U up to 124 mph (200 km/h)

H up to 130 mph (210 km/h)
V up to 149 mph (240 km/ h)
1
)
Z over 149 mph (240 km/h)1l
W up to 168 mph (270 km/h)
1 )
Y up to 186 mph (298 km/h)1l
Your vehicle is norma lly factory equipped with
tires, which possess excellent driving charac­
ter istics and give your Audi opt imum driving
comfort. An electronic speed limiter
c:> page 25 will normally prevent your vehicle
from go ing faster than the tire speed rating
¢ & .
U.S . DOT T ire Identific ation Numbe r (TIN)
and tire manufacture date
This is the t ire's "serial number" . It begins
with the lette rs "DO T" and indicates that the
tire meets all federal sta ndards. The next two
n umbers or le tters indica te the p la nt where it
was manufactured, and the last four numbers
represent the week and year of manufacture.
F or example, the numbers 2209 mean that
the t ire was produced in the 22nd week of
2009 . The other numbers are marketing co­
des that may or may not be used by the t ire
manufacturer . This information is used to con ­
tact consume rs if a tire defect requires a re­
call.
Aud i Original tire
Tires with the ident ificat io n "AO" or "RO" have
been spec ially matched with your Aud i. We
recommend using only t hese tires because
they meet the highest standards regard ing
safety and driving charac ter is t ics when used
correctly . Yo ur au thori zed Au di dealer w ill
g lad ly provide you with more information.
Maximum Load Rating
This number indicates the maximum load in
kilograms a nd pounds that ca n be carried by
the tire .
ll For tires wit h a max imum spee d capa bility over 149
mph (2 4 0 km/ h), ti re ma nufac tur ers somet imes use
t h e letters "Z R."
Tire s an d wheel s 225
Tire quality grading for treadwear,
traction, and temperature resi stanc e
Tread wear, traction and temperat ure grades
c:> page226.
Ma ximum Permissible Inflation Pressure
Th is number is the g reatest amount of a ir
pressure that should ever be put in the tire
u nder normal dr iv ing conditions.
.&_ WARNING ~
- Using incorrect o r unmatched tires and/
or wheels or improper tire and wheel
comb inat ions can lead to loss of control,
col lis ion and serious personal inj ury.
- Always use t ires, rims and whee l bolts
that meet the specifications of original
factory- installed tires or other combina­
tions that have been specifically ap­ proved by the vehicle manufacture r.
- T ires age even i f they are not being used
and can fail sudden ly , e specially at hig h
speeds. Tires that are more than 6 ye ars
old can only be used in an emergency
an d then w ith speci al care and at lower
speeds .
- Never mo unt used t ires on your veh icle if
you are not sure of thei r "previous histo­
ry." O ld used tires may have been dam ­
aged even though the damage cannot be
seen that can lead to sudden tire fai lure
and loss of vehicle control.
- All fou r whee ls must be fitted with radial
tires of the same type , size (rolling cir­
cumference) and the same tread pattern.
Driving with different tires reduces vehi­
cle handling and can lead to a loss of
contro l.
- If the spa re tire is not the same as the
tires that are mounted on the vehicle -
for examp le w ith winter t ir e s -only use
the spare t ire fo r a short pe riod of time
•
•

226 Tires and wheels
and drive with extra care. Refit the nor­
mal road wheel as soon as safely possi­
ble.
- Never drive faster than the maximum
speed for which the tires on your vehicle
are rated because tires that are driven
faster than their rated speed can fail
suddenly.
- Overloading tires cause heat build-up,
sudden tire failure, including a blowout
and sudden deflation and loss of control.
- Temperature grades apply to tires that are properly inflated and not over or un­
derinflated .
- For technical reasons it is not always
possible to use wheels from other vehi­
cles -in some cases not even wheels
from the same vehicle model.
- If you install wheel trim discs on the ve­
hicle wheels , make sure that the air flow
to the brakes is not blocked. Reduced air­
flow to the brakes can them to overheat,
increasing stopping distances and caus­
ing
a collision.
- Run flat tires may only be used on vehi­ cles that were equipped with them at the
factory. The vehicle must have a chassis designed for run flat tires and a factory­
installed tire pressure monitoring sys­
tem* that indicates a loss of tire pres­
sure . Incorrect use of run flat tires can
lead to vehicle damage or accidents .
Check with an authorized Audi dealer or
tire specialist to see if your vehicle can be
equipped with run flat tires . If run flat
tires are used, they must be installed on
all four wheels. Mixing tire types is not
permitted .
(D Note
-For technical reasons, it is not generally
possible to use the wheel rims from oth­
er vehicles. This can hold true for wheels
of the same vehicle type.
- If the spare ti re is different from the
tires that you have mounted on your ve­
hicle (for example winter tires or wide
profile tires), then use the spare tire for a short period of time only and
drive with
extra care. Replace the flat tire with the
tire matching the others on your vehicle
as soon as possible.
- If you put different wheels and tires on
your vehicle (e .g. winter wheels and
tires), you must be certain that the
wheels and tires are compatible with the
tire pressure monitoring system* . Other ­
wise the system will register a malfunc­
tion and a fault message will be dis­
played. For more information, contact
your authorized Audi dealer.
- Never drive without the valve stem cap .
The valves could get damaged .
@ For the sake of the environment
Dispose of old tires in accordance with the
local requirements.
Uniform tire quality grading
- Tread wear
- Traction AA A B C
- Temperature ABC
Quality grades can be found where applicable
on the tire side wall between tread shoulder
and maximum section width
¢ page 223,
fig. 171 .
For example: Tread wear 200, Traction AA,
Temperature A.
All passenger car tires must conform to Feder­
al Safety Requirements in addition to these
grades .
Tread wear
The tread wear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified
government test course.
For example, a tire graded 150 would wear
one and one half (11/2) times as well on the
government course as a tire graded 100.
The relative performance of tires depends
upon the actual conditions of their use, how-
ever, and may depart significantly from the
ll-

norm due to variations in driving habits, serv­
ice practic es and differences in road character ­
istics and climate .
Traction
The traction grades , from highest to lowest,
are AA, A, Band
C. T hose grades represent the
tire 's ability to stop on wet pavement as
m easured under controll ed conditions on
specif ied government test surfaces of asphalt
and concrete . A tire marked C may have poor
t raction performance¢ .&..
Te mperature
The temperature grades are A (the highest),
B, and
C, representing the tire's resistance to
the generat ion of heat and its ability to dissi­
pate heat when tested under controlled condi­
t ions on a specified indoor laboratory test
wheel.
Sustained high temperature can cause the material of the tire to degenerate and reduce
t ire life, and excessive temperature can lead
to sudden tire failure <=>& .
The grade C corresponds to a level of pe rform­
ance which all passenger car tires must meet under the Federal Motor Veh icle Safe ty Stand­
ard No .
109. Grades Band A represent h igher
l eve ls of pe rformance on the laboratory test
wheel than the m inimum required by law.
.8, WARNING
T he traction grade assigned to this t ire is
based on stra ight-ahead braking traction
tests, and does not include acceleration,
cornering, hydrop laning or peak traction
character istics .
A WARNING
The temperature grade for this t ire is es­
tablished for a t ire that is properly inflated
and not overloaded . Excessive speed, un­
derinflation, or excessive loading, either
separate ly or in combination, can cause
heat buildup and possible tire fa ilu re.
-
Tire s an d wheel s 22 7
Winter tires
Winter tires can improve vehicle handling on
snow and ice . At temperatures below 45 °F
(7 °C) we recommend changing to winter
tires.
In some heavy snow areas, local governments
may require true w inter o r "snow" t ires, those
with very deeply cut t read. These tires should
o nl y be used in pairs and be installed o n all
f o ur wheels . Make sure you p urchase snow
tires that are the same size and cons truction
type as the other tires on yo ur vehicle .
If your veh icle is eq uipped w ith all-whee l
drive *, th is w ill improve trac tion d uring win ter
driv ing, even with the s tanda rd tires. Howev ­
er, we strongly recommend that you always
equip all four wheels on your veh icle w ith cor­
rect ly fitted winte r ti res or all-season t ires,
when winter road conditions are expected.
This also improves the veh icle 's b rak ing per­
formance and reduces stoppi ng d ista nces .
Summer tires provide less grip on ice and
snow.
Winter tires (snow tires) must always be fitted
on all fo ur whee ls .
As k your au thori zed A udi dealer or qualified
workshop for permit ted
winter ti re size s. Use
on ly radial winter tires .
Win ter tires lose their effec tiveness whe n the
tread is worn down to a depth o f
0.1 57 inch
(4 mm) .
Only d rive w ith w inte r tir es under w inte r con­
di tions. S umme r tir es handle bette r when
t h e re is no snow o r ice on the ro ads and the
temperature is above 45 °F (7 °C) .
If you have a flat t ire, see notes on spare
whee l
¢page 223.
Please a lways remember that winter tires may
have a lowe r speed rating than the tires o rigi­
nally i nstalled on your veh icle at the time it
was ma nufactu red. P lease see ¢
page 224,
Speed rating (letter code)
for a lis ting o f th e
speed rating letter codes and the max imum
speed at which the tires can be driven .
111>-
•
•