204 Child Safety
&_ WARNING
Not using a child safety seat, using the
wrong child safety seat or improperly in
stalling a child restraint increases the risk
of serious personal injury and death .
-All vehicle occupants and especially chil
dren must always be restrained properly
whenever riding in a vehicle.
-
- An unrestrained or improperly restrain
ed child can be injured or killed by be
ing thrown against the inside of the ve
hicle or by being ejected from it during
a sudden maneuver or impact .
- An unrestrained or improperly restrain
ed child is at much greater risk of injury
or death by being struck by an inflating
airbag.
- Commercially available child safety seats
are required to comply with U.S. Federal
Motor Vehicle Safety Standard (FMVSS)
213 (in Canada CMVSS 213).
- When buying a child restraint, select
one that fits your child and the vehicle.
- Only use child restraint systems that
fully contact the flat portion of the
seat cushion. The child restraint must
not tip or lean to either side. Audi does
not recommend using child safety
seats that rest on legs or tube -like
frames . They do not provide adequate
contact with the seat.
-Always heed all legal requirements per
taining to the installation and use of
child safety seats and carefully follow
the instructions provided by the manu
facturer of the seat you are using.
- Never allow children under 57 inches
(1.45 meters) to wear a normal safety
belt. They must always be restrained by a
proper child restraint system. Otherwise,
they could sustain injuries to the abdo
men and neck areas during sudden brak
ing maneuvers or accidents.
- Never let more than one child occupy a
child safety seat . -
Never let babies or older children ride in
a vehicle while sitting on the lap of an
other passenger .
- Holding a child in your arms is never a
substitute for a child restraint system .
- The strongest person could not hold
the child with the forces that exist in
an accident. The child will strike the in
terior of the vehicle and can also be
struck by the passenger.
- The child and the passenger can also
injure each another in an accident.
- Never install rear-facing child safety
seats or infant carriers on the front pas
senger seat. A child will be seriously in
jured and can be killed when the passen
ger airbag inflates -even with an Ad
vanced Airbag System .
- The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat
and child against the backrest, center
armrest, door or roof .
-Always install rear-facing child safety
seats or infant carriers on the rear seat .
- Forward-facing child safety seats instal
led on the front passenger 's seat can in
terfere with the airbag when it inflates
and cause serious injury to the child. Al
ways install forward-facing child safety
seats on the rear seat .
- If exceptional circumstances require the
use of a forward-facing child restraint on
the front passenger's seat, the child's
safety and well-being require that the
following special precautions be taken :
- Make sure the forward-facing seat has
been designed and certified by its man
ufacturer for use on a front seat with a
passenger front and side airbag.
-Always carefully follow the manufac
turer's instructions provided with the child safety seat or carrier.
- Always move the front passenger seat
into the rearmost position of the pas
senger seat's fore and aft adjustment range, and as far away from the airbag
as possible before installing the child
restraint.
- Always make sure that nothing pre
vents the front passenger's seat from
be ing moved to the rearmost position
in its fore and aft adjustment range.
- Always make sure that the backrest is
in the upr ight position.
- Always buck le the child safety seat firmly
in place even if a child is not sitting in it.
A loose ch ild safety seat can fly around
dur ing a sudden stop or in a col lision .
- Always read and heed all WARNINGS
whenever using a child restrained in ave
hicle is being used~
page 170, Safety
belts,
~ page 179, Airbag system and
¢ page 200, Child Safety.
A WARNING
T o reduce t he ris k of serious injury, make
sure that the
PASSENGER AIR BAG OFF
light comes on and stays on whenever a
child rest raint is installed on the front pas
senger seat and the ignition is switc hed
on.
- Take the child restraint off t he fro nt pas
senger seat and install it properly at one
of the rear seat positions if the
PASSEN ·
GER AIR BAG OFF
light does not stay on.
- Have the airbag system inspected by
your authorized Aud i dealer immediate
ly.
A WARNING
A child in a child rest raint installed w ith
the LATCH lower anchorages or w ith the
standard safety belt on the rear seat may
play wi th unused rear seat safety belts and
become entangled res ulting in ser ious per
sonal inj ury and even dea th.
- Always bu ckle unused rea r seat safety
bel ts out of re ach of chi ld ren in ch ild
sea ts and properly a ctivate the converti
ble locking retrac tor so that the child
cannot un reel the safety belt from the
retractor .
-
Child S afety 205
Child safety seats
Infant seats
Babies and infants up to about one year old
and 20 lbs. or 9 kg need special rearward-fac
ing child restraints that support the back,
neck and head in a crash.
F ig . 20 4 Schematic overview: rearward-fac ing infant
seat, properly installed on t he rear seat
... When usi ng the vehicle safety belt to install
a child safety seat, you m ust first activate
the convertib le locki ng retractor on the
safety belt to p revent the child safety seat
from moving~
page 209 or install the seat
using the LATCH attachmen ts .
... Push the chi ld safety seat down with your
full weig ht to get the safety belt really tight
so that the seat cannot move forward or
sideways more than one inch (2.5 cm).
Infants up to about one year
(20 l bs. or 9 kg)
are best protected in specia l infant carriers
and child safety seats designed for their age
group. Many experts believe that infants and
small children should r ide on ly in special re
stra ints in wh ich the child faces the back of
the vehi cle. These infant seats support the ba
by 's back, ne ck and head in a crash
¢ fig. 204.
The airbag on the passenger side makes the
front seat a pote ntia lly dange ro us place for a
ch ild to ride. Th e front seat is not t he safest
pla ce for a child in a fo rward-facing child sea t.
It is a very dangerous place fo r an in fant or a
larger child in a rearward-facing seat. .._
than 20 lbs. (9 kg) up to 40 lbs. (18 kg) must
always be properly restrained in a child safety
seat certified for their size and weight
c:> fig. 205 and c:> fig. 206.
The airbag on the passenger side makes the
front seat a potentially dangerous place for a
child to ride. The front seat is not the safest
place for a child in a forward-facing child safe
ty seat.
It is a very dangerous place for an in
fant or a larger child in a rearward -facing seat .
.,&. WARNING
Not using a child safety seat, using the
wrong child safety seat or improperly in
stalling a child restraint increases the risk
of serious personal injury and death in a
collision or other emergency situation.
- Children on the front seat of any car,
even with Advanced Airbags, can be seri
ously injured or even killed when an air
bag inflates. A child in a rearward-facing
child safety seat installed on the front
passenger seat will be seriously injured
and can be killed if the front airbag in
flates -even with an Advanced Airbag
System.
- The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat
and child against the backrest, center
armrest, door or roof.
- Always install rear-facing child safety
seats on the rear seat.
- If you must install a rearward facing
child safety seat on the front passenger
seat because of exceptional circumstan
ces and the
PASSENGER AIR BAG OFF
light does not come on and stay on, im
mediately install the rear-facing child
safety seat in a rear seating position and
have the airbag system inspected by your
Audi dealer.
- The rear side of the child safety seat
should be positioned as close as possible
to the backrest on the vehicle seat. Ad
just or remove the rear seat head re straint if it is difficult to install the child
Child Safety 207
seat with the head restraint in place
c:> page 77. Install the head restraint
again immediately once the child seat is
removed . Driving without head restraints
or with head restraints that are not prop
erly adjusted increases the risk of serious
or fatal neck injury dramatically.
- Always read and heed all WARNINGS
whenever using a child restrained in ave
hicle is being used
c:> page 170, Safety
belts,
c:> page 179, Airbag system and
c:> page 200, Important things to know.
.,&. WARNING
If exceptional circumstances require the
use of a forward-facing child restraint on
the front passenger's seat, the child's safe
ty and well-being require that the follow
ing special precautions be taken:
- Make sure the forward-facing seat has
been designed and certified by its manu
facturer for use on a front seat with a
passenger front and side airbag .
-Always follow the manufacturer's in
structions provided with the child safety
seat or infant carrier .
- Always move the front passenger seat in
to the rearmost position of the passen
ger seat's fore and aft adjustment range,
and as far away from the airbag as possi
ble before installing the child restraint.
- Always make sure that nothing prevents
the front passenger's seat from being
moved to the rearmost position in its
fore and aft adjustment range.
- Always make sure the backrest is in an
upright position.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched on.
- If the light does not stay on, perform the
checks
c:> page 190, Monitoring the Ad
vanced Airbag System.
- Take the child restraint off the front pas-
-
senger seat and install it properly at one ~
•
•
A WARNING
Forward-facing child restraints:
- Always make sure the forward-fac ing
seat has been des igned and certified by
its manufacturer for use on a front seat
with a passenger front and side airbag.
- Never put the forwa rd -facing child re
straint up, against or
very near the in
strument panel.
-Always
move the passenger seat into its
rearmost position in the seat's fore and
aft adjustment range, as far away from
the a irbag as poss ible before installing
the forward-facing child restraint. The backrest must be adjusted to an upr ight
posit ion .
- Make sure that the
PA SSENGER AIR BAG
OFF
light comes on and stays on all the
t ime whenever the ignition is switched
on.
A WARNING
Rearward-fac ing c hild restra ints:
- A ch ild in a rearwa rd-facing child safety
seat installed on the front passenge r
sea t will be ser iously injured and can be
killed if the front airbag inflates -
even
with an Advanced Airbag System.
- T he inflating a irbag w ill hit the child
sa fety sea t or infant carrier w ith g reat
f orce and w ill smash the ch ild safety seat
and child against the backrest, cente r
armrest, door or roo f.
- Always be especially caref ul if you must
install a rearward facing child safety seat
on the front passenger seat in exception
al circumstances.
- A tight tether strap on a rearward-facing
child restraint attached to the front pas
senger seat can put too much pressure
on the weight-mat in the seat and reg is
ter a heavier weight in the Advanced A ir
bag System. The heav ier we ight regis
tered can make the system work as
th ough an adult were on the seat and de
ploy the Advanced Ai rbag when it must
Child Sa fet y 211
be suppressed causing serio us or even
fatal injury to the ch ild.
- Make sure that the
PASSENGER AIR BAG
OFF
li ght comes on and stays on all the
time whenever the ignit ion is switched
on.
- I f the
PASSENGER AIR BAG OFF light
does not come on and stay on, immed i
ately insta ll the rear-facing child safety
seat in a rea r seat ing pos ition and have
the airbag system inspected by your Audi dea le r.
Activating the convertible locking
retractor
Use the convertible locking retractor to se
cure a child restraint.
Always heed the ch ild safety seat manufactur
er's instr uctions when installing a child re
stra in t in your veh icle. To a ctivate the conve r
t ible Lac king re tr actor:
"' Place the child rest raint on a seat, p re fera
bly on the rea r seat.
"' Slowly pu ll the belt
all the way out .
"' Route i t aroun d or throug h the ch ild re
s train t belt path
¢ .&_ .
"' Push the chi ld safety seat down with your
fu ll weight to get t he safety be lt really tight.
"' Insert the belt tong ue into the b uckle for
that seating position.
"' Guide the safety be lt back into the retractor
until the be lt lies flat and snug on the ch ild
safety sea t.
"' Yo u should hear a " clicking" no ise as the
be lt winds back i nto the inertia ree l. Test the
c onvert ible lo cki ng ret ra ctor by pulling on
the belt . You sho uld no longer be able to
pull t he be lt out of the retractor . The con
vertible locking retractor is now activated.
"' Ma ke s ure that the red release button is fac
ing away from the child restraint so that it
can be unbuckled qu ick ly.
"' Pull on the belt to make sure t he safety belt
is prop erly tight and fasten ed so tha t the
seat ca nnot
move forwa rd or sideways more
t han one inch (2.5 cm). .,. •
•
226 Intelligent technology
can result in there being insufficient energy
avai lab le to start the engine .
I ntell igent energy management in your vehi
cle handles the distribution of electrical ener
gy . Starting abi lity is markedly improved and
the life of the battery is extended .
Basically , energy management consists of
battery diagnosis , idling current manage
ment
and dynamic energy management.
Battery diagnosis
Battery diagnosis continuously determines
the state of the battery. Sensors determine
battery volta ge, battery current and battery
temperature. This determines the current
state of charge and the power of the battery.
Idling current management
Idling current management reduces energy
consumption while the vehicle is stand ing.
With the ignition switched off, it contro ls the
energy supply to the various e lectrica l compo
nents. Data from battery diagnosis is consid
ered.
Depending on the battery's state of charge,
individua l consumers are gradually turned off
to prevent excessive discharge of the battery
and thus maintain starting capability.
Dynamic energy management
While the vehicle is being dr iven , dynamic en
e rg y management distributes the energy gen
erated according to the needs of the individu
a l components. It regulates consumption, so
that more ele ctrical energy is not being used
than is being generated and ensures an opti mal state of cha rge for the battery.
{D) Tips
- But even energy management cannot
negate the limits of physics. Consider
that the power and life of a battery are
limited .
- If starting ab ility is threatened, you are
i nformed by a warn ing
c> page 22 7,
Driver notification in the instrument
cluster display .
What you should know
The highest priority is given to maintaining
starting capability .
The battery is seve rely taxed in shor t-distance
driving, in city tra ffic and dur ing the cold time
of year . Abundant electrical energy is re
quired, but only a little is generated . It is also
critical if the engine is not running and e lectri
ca l components are turned on . In this in
stance energy is being consumed but none is
being generated.
It i s in precisely these situations that you will
notice energy management actively regulat
ing the distribution of energy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period
of several days or weeks , e lectr ica l compo
nents are gradually cut back or sw itched off.
T his reduces energy consumption and main
ta ins start ing capability over a longer period .
Take into consideration that when you unlock
your vehicle , some conven ience functions ,
s uc h as the inte rior lights or the power seat
adjustment, may not be available. The con
venience functions will be available again
when you turn on the ignition and start the e ngine .
With the engine turned off
If you listen to the radio, for example, w ith
the engine turned off or use other MMI func
tions, the battery is being discharged .
If starting capability is jeopardized due to en
ergy consumption , the following warning ap
pears in the MMI display:
Please start engine, otherwise system will
switch off in 3 minutes .
The warning indicates that the system will be
turned off automatically after 3 minutes . If
you w ish to continue using the funct ions, you
have to sta rt the eng ine.
1111>
2 70 Chec king and filling
should only be disconnected from the vehicle
e lectrical system when absolutely necessary
for repairs.
Vehicles not driven for long periods
If you do not drive your vehicle over a pe riod
of several days or weeks, electrical compo
nents are gradually cut back or switched off.
This reduces energy consumption and main
tains starting capab ility over a longer period
c;, page225.
Take into consideration that when you un lock
your vehicle, some convenience functions, such as the interior lights or the power seat
adjustment, may not be available. The con
venience functions will be available again
when you turn on the ignition and start the
engine .
Winter operation
During the winter months, battery capacity
tends to decrease as temperatures drop . This
is because more power is also consumed while
starting, and the headlights, rear window de
fogger, etc., are used more often .
Avoid unnecessary power consumption, par
ticularly in city traffic or when traveling only
short d istances . Let your authorized Audi
dealer check the capacity of the vehicle bat
tery before w inte r sets in
¢ page 271. A well
cha rged battery w ill not only prevent starting
p rob lems when the weather is cold, but will
a lso last longer.
(D Tips
If your vehicle is left standing for several
weeks at extremely low temperatures, the
vehicle battery should be removed and
stored where it will not freeze . This wi ll
prevent it from being damaged and having
to be replaced.
Working on the battery
Be especially careful when working on or near
the battery.
The battery is located under the driver 's seat.
Before you check anyth ing under the driver 's
seat,
read and heed all WARNINGS c:;, _&.
Always heed the safety warnings, when work
ing on the vehicle battery or the vehicle elec
trical system to prevent injury.
The following WARNINGS are very
important when working on the battery:
Always heed the following WARNING SYM BOLS and safety precautions when working
on the battery.
@!) Always wear eye protection .
b.. Battery acid contains sulfuric acid . Al
~ ways wear gloves and eye protection.
~ No
\!:51 -sparks
- flames
- smoking.
A. When a battery is charged, it produces
~ hydrogen gas which is explosive and
could cause personal injury.
~ Always keep the battery well out of
~ reach of children.
,&. WARNING
Whenever working on the battery or on
the electrical system, there is the risk of
injury, accident and even fire . Read and
heed the following WARNINGS:
- Always wear eye protection. Do not let
battery ac id or any lead particles get on
your skin or clothing. Shield your eyes .
Exp losive gases can cause blindness or
other injury.
- Battery acid contains sulfuric acid. Sulfu
ric acid can cause blindness and severe
burns.
- Always wear g loves and eye protection.
-
Do not tilt the battery because acid ~
304 Fuses and bulb s
.
Left cockpit fuse assignment
Fig. 257 Left cockpi t: fu se pa nel w ith plas tic cl ip
Fu se pa nel @ (red )
1
3 MMI
6
7
8
9 Lumbar support driver's seat
Window regulators (left side of
vehicle) Door control module (left side
of vehicle)
Tire pressure monitoring sys
tem Electronic ignition lock,
10 power steering column adjust-
I ment
11 Switch module steering co lumn
Intelligent power module con
venience
F u se pa nel @ (b ro wn)
3
6 Horn
5
7,5
35
15
5
30
10
5
5
25
No .
7
8
9
Consumer
Intelligent power module driver
I ntell igent power mod ule driver
(lights left side of vehicle)
Intelligent power module driver (lights right side of vehicle)
10 Instrument cluster
11 Headlight washer system
12 Diagnostic connector
Fuse pane l c (black )
1 Headlight electron
ic system
(left side of vehicle)
Adaptive cruise control
Terminal 15 (interior)
Diagnostic connector
9 Automatic dipping interior mir-
ror
10 Homelink
11 Control module Gateway
12 Headlight range adjustment
-Amps
30
25
25
10
30
10
10
5
5
5 5
5
5
Fuse s and bulb s 305
Right cockpit fuse assignment
Fig . 258 Right cockp it: f use pane l w ith plastic clip
No. Con sumer Amps No. Consumer Amps
Fu se pa nel@ (bla ck )
6 Automatic transmission
5/20
1 Heated rear seats
7
E lectronic Stability Control
5
2 Telephone, cell phone package (ESC)
--Shift gate automatic transmis-
Front seat hating/seat ventila-
8 5
3 30/15
tion (right) sion
Electron ic Stab ility Control 9 Parking system
5
4 (ESC) 20
10 Airbag
5
5 Door control module (right side
15 11
Heated rear seats
5
of vehicle) 12 Air-conditioning 5
6 Rear electrical outlets 25 Fuse panel© (red )
7
Lumbar support passenger's
10 1 Instrument cluster
seat 2 Rearview camera
8 Ciga
rette lighter front 20
3 CD player, DVD drive 5
9 Front electrical outlets
25 4 MMI Display 5
10 A/C controls 10
5 Automatic transmission
11 Cooler
15 Panoramic sliding sunroof seg-
7 20
12 Inte
lligent power module pas-
15 ment 1
senger Panoramic sliding sunroof seg-
Fuse panel B (brown ) 8 ment2 20
1 Headlight e
lectronic system
10 Panoramic sliding sunroof sun-
9 20
(right side of veh icle)
blind
Ride height adjustment 5
Window regulators (right side
Telephone package 5 11
of vehicle) 35
4 12 Rear air-condi
tioning contro ls 10
5 Electronic
Stability Cont rol
5
(ESC)