2012 AUDI A8 warning light

Instruments and warning/indicator lights 17
9::;r: Engine oil pressure malfunction
The red engine oil pressure warning symbol
requires immediate service or repair . Driving
with a Low-oil-pressure indication is Likely to
inflict severe damage to the engine .
• Switch off engine and check oil level
If the indicator light t urns on the message ap­
pears, the oil press ure is too low.
~ P ull off the road.
~ Stop t he ve hicle .
~ Turn off the engine.
~ Check the engine oil level¢ page 224 .
~ If the engi ne oil leve l is too low, add engine
o il ¢
page 225. M ake sure that the oil p res­
s ur e warning symbol. appears no longer
in t he d is pl ay befo re y ou start driving aga in.
~ If the engine oil leve l is cor re ct an d the ind i­
c a tor lig ht still tur ns o n, tur n t he eng ine
off
and do not contin ue d riving . Seek professio ­
nal assistance.
(D Tips
- The engine oil pressure symbol. is
not an indicator for a low engine oil lev­
el. Do not rely on it. Instead, check the
oil level in your engine at regular inter­
vals, preferably each time you refuel,
and always before going on a long trip.
- The yellow oil level warning indication
II requires oil refill or workshop serv­
ice without delay. Do not wait until the
red oil pressure warning. starts to
flash before you respond to the low oil level warning
l!I. By then, your engine
may already have suffered seriou s dam­
age .
~ . Engine oil level
• WARNING: Please add oil immediately
When t he sy mbo l and the dr iver message a p­
pea r, the oil has to be reple nished r ight now
¢page 222.
If the indicator lig ht and th e message ap pear,
a d d engine o il i mm edi ate ly
¢page 225.
II Add oil , max . x qt (l). You may continue
driving
Whe n the symbol and the d river message ap­
pear, add the amoun t of oil appear ing in the
display at the nex t oppo rtuni ty ¢
page 222.
® -Steering column lock
• Do not drive vehicle: Steering defective
If th e indic ator li ght turns on and the mes ­
sa ge appe ars, there is an e lectroni c steering
column lock malf unct ion . You cannot switch
the ignit ion on.
D o
not tow yo ur vehicle beca us e it cann ot b e
s tee red. See k profession al assistance .
!'J!I Steering lock : system fault . Please con­
tact dealer
If the indicato r light turns on and the mes­
sage appea rs , t here is an e lectronic stee ring
column lock malfunct io n .
Drive to your auth orized A udi dealer immedi­
ately to hav e th e m alfunction corr ect ed .
A WARNING -
Your vehicle m ust not b e tow ed in t he
eve nt of a ma lfunction in the elec tronic
st eer ing col umn lo ck b eca use i t cann ot be
s teere d du e to the lock ed s tee ring. If it is
towe d wit h the steer ing lo cke d, there is
the r isk o f an acci dent.
© -Engine start system
• Engine start system fault. Please con­
tact dealer
If the indica to r li ght tur ns on and the mes­
sage a ppea rs, do
not switch the ignition off
because you may not be ab le to sw itch it on
again.
D rive to your autho rized A udi de aler imme di­
ate ly to have the ma lfunction corrected.
• Engine start system fault . Plea se con­
tact dealer

18 Instruments and warning/indicator lights
If the indicator light turns on and the mes­
sage appears, there is a ma lfunction in the en ­
g ine start system.
Drive to your authorized Aud i dealer immedi­
ate ly to have the malfunction cor rected .
0 Air suspension
• Air suspension: system fault. Can contin­
ue slowly with max. 35 mph .
There is a malfunction that can result in re­
stricted driving stability .
Ca refully drive at a maximum speed of 35
mph
(60 km/h) to your authorized Audi dealer
or qualified workshop to have the malfunction
corrected .
• Air suspension: service mode. Vehicle
can only be moved with restrictions
Carefully drive to your authorized Audi dealer
or qualified workshop immediately to have
the service mode deactivated.
Ill Air suspension fault
There is a system ma lfunction that can result
in restr icted driving stability or reduced
ground clearance.
Drive to your authorized Audi dea ler immedi­
ate ly to have the malfunction corrected.
IIJ Air suspension: vehicle too low. Ground
clearance reduced
The ground clea rance is ve ry low due to a sys­
tem malfunct ion. Wait until the air suspen­
sion system has restored normal ground clear­
ance . Otherwise, conditions such as an uneven
road surface can lead to ve hicle damage.
~/ !f Safety systems
The fl (USA models) ;BI (Canada models) in­
d icator light monitors the safety systems e.g.
a ir bags, pretensioners and illum inates for a
few seconds each time you switch the ignition
on .
If the
I (USA models) ;BI (Canada models)
indicator light does not go out, or if it illumi- nates while you are driving, or if it starts to
blink,
then there is a malfunction somewhere
in the system.
If the light does not illuminate
when you switch the ign it ion on, th is also
means there is a malfunct ion.
A WARNING '"--
If you have a ma lfunction in the safety sys-
tems, contact your authorized Audi dea ler
imme diately. Otherwise the safety sys­
tems may not work properly in an acci­
dent.
fJJ [}, Electronic Stability Control (ESC)
This warning/indicator light monitors the
Electronic Stability Control.
When you switch the ignition on, the indicator
light
G1 turns on briefly to check the function.
If the
J.iJ ind icator lamp blinks wh ile driving,
the ESC or ASR (Anti-Slip Regulation) is active­
ly regulating.
If
the DJ ind icator lamp illuminates, the sys·
tern has switched the ESC off.
If the indicator light fi turns on, the ESC was
switched to ESC sport mode with the button
[!] c::, page 187. If this is case, you can reacti­
vate the ESC by switching the ignition off and
then on aga in. The warning/indicator light
should go out to show that the system is fully
functional again .
Stability program and ABS fault! See own­
er 's manual
If the indicator light DJ and the ABS indicator
li ght
m (USA models) ;II] (Canada models)
turn on and the message appears, there is a malfunction in the ABS system or electronic
differential lock. Th is also interrupts the ESC.
The brakes still funct ion wit h their normal
power, but ABS is not active .
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected .
If the battery terminals were disconnected
and re-connected, the vehicle was jump start-
ed or the battery is very weak, the ESC sensor .,,.

Instrument s and warnin g/indic ator ligh ts 19
system goes through a learning process fo r
the first few yards . The warning/indicator
light ill uminates. The warn ing/indicator light
goes out as soon as the learning process is
complete.
F or more information about the ESC
~page 187.
ABS/(8) Anti-lock braking system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL).
The warning/indicator ligh t m (USA mod­
e ls)
.11] (Canada models) will come on for a
few seconds when the ignition is switched on.
The light will go out after an automatic check
sequence is completed.
There is a malfunction in the ABS wh en :
- T he warning/indicator lig ht does not illumi­
nate when you switch the ignition on.
- T he warning/ indicator lig ht does not go out
after a few seconds.
- T he warning/indicator light ill uminates
whi le driving.
The ESC indicator light a lso illuminates if
there is a malfunction in the ABS. The mes­
sage
S tabilit y prog ram and ABS faul t! S ee
o w ner' s manu al
also appears in the inst ru­
ment cluster display and a warning tone
sounds.
Th e br ake sy ste m will still r espond ev en
with out the a ssis tan ce of the ABS sy ste m .
See your a uth orized Audi deal er as s oon a s
po ssible to re sto re full br akin g perform anc e.
For more information regarding the ABS
¢page 187.
Malfunction in the brake sy stem
If the b rake warning light~ page 14 and the
ABS warning illuminate
together there may be
a ma lfunction in the ABS, and there may also
be a ma lfunction in the brake system itself
¢ &,. The ABS wi ll not work a nd you will no ­
tice a chang e in br aking r espo nse a nd p er­
forman ce.
In the event of a malfunction in the br ake
sys tem
the warning/indicator light _
(USA mode ls)/ . (Canada mode ls) in the in­
strument cluster flashes¢
page 14.
Malfunction in th e electronic d iff erential
l o ck (EDL)
The EDL works together with the ABS. The
ABS warning light will come on if there is a
malfunction in the EDL system
¢page 187.
See your authorized Audi dealer as soon as
poss ible.
A WARNING
- If the m (USA models)/ rl] (Canada
models) warning light does not go out,
or if it comes on while dr iving, t he ABS
system is not working properly. The vehi­
cle can then be stopped only w ith the
standard brakes (without ABS) . You w ill
not have the protect ion ABS prov ides.
Contact your Audi dea ler as soon as pos­
sible.
- USA models: If the - warning light,
the
W warning light and the B warn­
ing light come on together, the rear
wheels could lock up first under hard
brak ing. Rear wheel lock-up can ca use
loss of vehicle control and an accident.
Have your vehi cle repaired immediately
by your au thori zed A udi dealer or a quali­
fied workshop . Dr ive slowly and avoid
sudden, hard brake applications.
- Canada models: If the brake warning
light ., the
B'J warning light and the
ABS warning light
II] come on together,
the rear wheels could lock up first under
hard braking. Rear whee l lock-up can
cause loss of vehicle contro l and an acci­
dent. Have your veh icle repa ired immedi­
ately by your authorized Audi dealer or a
qualified workshop. Drive s lowly and
avoid sudden, hard brake applications.
(0 ) Worn brake pads
£i Brake pad s!

20 Instruments and warning /indicator lights
If the warning light illuminates, immediately
contact your authorized Audi dealer or quali­
fied workshop to have all brake pads inspect­
ed. On USA models the warning light
El
comes on together with the warning light
- · Both sets of brake pads on an axle
must always be replaced at the same time .
A WARNING
Driv ing with bad brakes can cause a colli­
sion and serious personal injury.
-If the warning light El and the warn ing
light
- 1) with the message Brake
pads!
comes in in the inst rument cluste r
display, immediately contact your au­
thorized Audi dealer or qualified work­
shop to have all brake pads checked or
replaced if necessary.
EPC Electronic power control
This warning/indicator light monitors the
electronic power control.
The~ warning/indicator light (Electronic
Power Control) illuminates when you switch
the ignition on as a function check.
@ Tips
If this warning/indi cator light ill uminates
while you are driving, then there is a mal­
function in the engine electronics. Have
the malfunction corrected as soon as pos­
sible by your authorized Aud i dea ler or
qualified repair facility.
o Malfunction Indicator Lamp (MIL)
The Malfunction Ind icator Lamp (MIL) is part
of the On-Board D iagnostic (OBD II) system .
The symbol
¢4ii lights up when the ignition is
switched on and w ill turn off after the engine
has started and has sett led at a constant idle
speed. This ind icates that the MIL is working
properly.
l ) - : USA mod els only
-
The warning light illuminates when there is a
malfunction in the engine electronic system.
Contact your authorized Audi dea ler and have
the malfunction corrected.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
¢page 217.
For more information ~ page 26.
!?'i Engine speed limitation
Applies to vehicles: with engine speed limitatio n
Ill Engine speed maximum XXXX RPM
The eng ine speed is automatically limited to
the speed displayed in the driver information
system . This protects the engine from over ­
heating.
T he eng ine speed limitation deactivates once
the engine is no longer in the critical tempera­
ture range and you have re leased the accelera­
tor pedal once.
If the engine speed limitation was activated
by an engine control malfunction, the indica­
tor light~ also turns on. Make sure that the
speed does not go above the speed displayed .
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected .
~ .. Engine oil level
II Add oil, max. x qt (l). You may continue
driving
When the symbol II and driver message ap­
pear, add the amount of oil appearing in the
display at the next opportunity¢
page 225.
~,.. Engine oil sensor
II Oil level! Sensor defective
If the symbol illuminates, contact your au­
thorized Audi dealer and have the oil sensor inspected . U ntil you have this done, check the
o il level each time you refuel just to be on the
safe side ~
page 224.

Instruments and warning/indicator lights 21
Bu Fuel level indicator
II Please refuel
If the indicator light turns on for the first
time and the message appears, there are
about 4 ga llons (15 liters) of fuel left in the
tank . T im e to refuel
<=>page 216.
II Tank system malfunction! Contact dealer
If the indicator light turns on and th is mes­
sage appears, there is a malfunction in the
tank system.
Drive to your authorized Audi dea ler immedi­
ately to have the malfunction corrected .
co Windshield washer fluid level
II Please refill washer fluid
If the symbol illuminates, add windshield
washer fluid to the washer system/headlight
washer system* <=>
page 234.
4I:> Windshield wipers
!I Windshield wiper defective
There is a malfunction with the windshield
wipers.
Drive to your authorized Aud i dealer immedi­
ately to have the mal function cor rected .
~!}0 10$ Defective light bulb warning
I-If the indicator light turns on, a bulb has
fa iled. The message indicates the location of
the bulb.
II-if a fog lamp* has failed, the ind icator
light t urns on to indicate the location on the
vehicle.
[ti-if a rea r fog lamp has failed, the ind icator
light turns on to indicate the location on the
vehicle .
Vehicle lights: malfunction
If the message appears, there is a malfunc­
tion in the headlights or light switch. Drive to
your authorized A udi dealer immedi­
ate ly to have the ma lfunction corrected.
A WARNING
- Light bulbs are pressurized and could ex­
plode w hile they are being changed ca us­
ing serious personal injury.
- Work with due care when hand ling the
high-voltage sect ion of gas discharge
(xenon) lights. Failure to do so could re­
sult in death or serious injury.
(1) Tips
Have the bu lb replaced or the connection
repaired by your authorized Audi Service
department.
i.lD Headlight range control
II Headlight range control: defective!
If the symbol illuminates, the headlight range
control is no longer work ing properly. Have
the system checked and repaired at your Audi
dealer .
~0 Adaptive Light
Applies to veh icles: w it h Adaptive light
ml Audi adaptive light: system fault
If the indicator light turns on and this mes­
sage appears, there is a malfunct ion in the
adaptive light system. The headlights st ill
function.
Go to an authorized dealersh ip to have the
headlights or the control unit for the Adaptive
Light repa ired .
@ Light/rain sensor
!I Automatic headlights/automati c wipers:
system fault
If the indicato r light turns on and this mes­
sage appears, the light/rain sensor is not
funct io nin g correctly.
For safety reasons the low beams are turned
on permanently with the switch in
AUTO . liJI,

22 Instruments and warning /indicator lights
However, you can continue to turn the lights
on and
off using the light switch . You can still
control a ll funct ions that are independent of
the rain sensor through the windshield wiper lever.
Contact your authorized Audi dealer as soon
as possible to have the prob lem corrected.
@! Dynamic steering
1;r.ij Steering: system fault. you can continue
driving
If the indicator light turns on and the mes­
sage appears, the steering may be more diffi­
cult to move or more sensitive than usual. The
steering wheel may also be at an angle when
driving straight .
Drive slow ly to your authorized Audi dealer or
qualified workshop to have the malfunction
corrected.
tT@ Dynamic steering: initialising
If th is driver message appears and the ind ica­
tor light is flashing on the instrument panel,
dynamic steering is being reinitialized. Once
you start the engine after this is finished, the steering wheel w ill be easy to move . Re-initi ­
alization might be necessary if the steering
wheel was moved hard to the left and r ight
while the veh icle was not moving . The display
goes out as soon as init ialization is complete .
A WARNING
-
Have the dynamic steering system mal­
function repaired as soon as possible by an
authorized Audi dealer or any qualified
workshop -risk of accident!
@ Tips
-The dynamic steering stability systems
are not available in the event of a system
malfunction.
- For additional informat ion on dynamic
stee ring, refer to
¢page 103.
I-: Sport differential
II Sport differential: system fault
There is a malfunction with the sport d ifferen ­
t ial.
Drive to your authori zed Audi dealer immedi­
ately to have the malfunction corrected .
II Sport differential: overheating
The transmission temperature has increased
s ignificantly due to the sporty driving manner.
Drive in a less sporty manner until the tem­
perature returns to the normal range and the
indicator light switches of.
A WARNING
Contact your authorized Audi dealer or a
qualified workshop if the sport differential
is faulty or malfunct ioning . The repair
must be performed by trained personnel
using the correct oil in order to ensure
safety.
¢ 9 Turn signals
-
The indicator light blinks when you use either
turn signal .
Whenever you use the left B or the right B
turn signal, the indicator light blinks. When
you use the emergency flashers , both indica­
tor lights flash .
If one of the turn signal light bulbs burn out,
the turn signal will blink twice as fast as nor­ mal. Carefu lly dr ive to your authorized Audi
dealer immed iately to have the malfunction
corrected. The indicator light does not indi­
cate a malfunction if a turn signal on the trail­
er or on the vehicle fails in trailer towing
mode.
@ Tips
For more information on the turn signals,
refer to
¢ page 45.

Instrument s and warning /indicator lights 23
Driver information
display
Overview
Fig. 4 Driv er in formation system in t he in strum en t
cl uster
Fig . 5 D isplay: e xample of th e informa tion line
The driver information system contains infor­
mation
® that is displayed on tabs ®
c::> fig. 4. The follow ing content is possibl e de­
pending on vehicle equipment:
®
Tab
1
2
---
®
Content
Vehicle functions:
On-board computer <=;>page 24
Digital speedometer
Cruise control*
c::> page 85
Adaptive cru ise control and Audi
braking guard*
c::>page 87
Audi lane assist* c::> page 96
Display darkened
Indicator lights and messages
Warning when a door, the hood or
the rear lid is not closed
c::> page 26
Service interval display¢
page 25
Speed warning system ¢ page 85
--
® ®
Tab Content
3 Night vision assistant* c::> page 106
4 Audio/video
s Telephone*
6 Navigation*
The second and th ird tabs are only v isible if at
least one indicator light or message is shown
o r i f that system is switched on .
The status line © is located in the bottom
part of the d isplay
c::> fig . 4. It displays the ex­
terior temperature , time , selecto r lever posi­
tion, trip odometer and odometer.
I
For some vehicle functions, you can access the
trip information from the temporary memory
r::!;> page 24 i n the line (D c::> fig. 5.
& WARNING ,.______ -
- Never re ly exclusively on the outside
temperature display to determine if a
road surface is icy or not. Keep in mind
that road surfaces, especia lly bridges
and overpasses, could be ice covered and
slippery even at an outside temperature
above 41 °F ( +S
0
() .
-Always remember, even if the "snow­
flake" symbol (ice warning) does not ap­ pear in the display, black ice could be on
the road .
- Always reduce your speed and drive with
special care in cold weather conditions
when the chance of encountering icy road surfaces increases.
(i) Tips
-At temperatures below 14 °F (+ S 0
() a
snowf lake symbol appears ahead of the
temperature display .
It is intended to re­
mind the driver to pay special attention
to
ice on the road c::> &. If the vehicle is
stationary, or if you are driving at a very
low speed, the temperature shown in the
display might be slightly higher than the
actual outside temperature. This is

24 Instruments and warning /indicator lights
ca used by the he at being radiated from
t h e engine.
- Y ou can se lect the units used for temper­
atu re, speed and other measurements i n
the MMI.
- Fo r i nforma tion on the a udio/video and
navigation* functions, refer to the se pa­
r ate MMI owner's manual.
Operation
The driver information system is operated us ­
ing the buttons on the multifunction steering
wheel.
en
~------,~
;;i,
Fig . 6 Mult ifunct io n steer in g whee l: ope rat ing t he d riv ­
er informa tion sys tem
Fi g. 7 Driver info rm ation system : open ing t he ve hicle
f unct io ns m en u
Operating concept
.. Switch the ignition on.
.. To sw itch between the tabs, press the rock­
er switch @to the left or right¢
fig. 6.
.. To access addi tional info rmat ion be low or
above, rotate the thumbw heel @ dow n or
u p.
.. To confi rm a se lecti on, press the thum b­
w hee l@ .
Accessing Vehicle functions
.. Sele ct the first t ab with the ro cker swi tch
@ .
.. Press the button ~-Th e Vehicle funct ions
menu appears ¢ fig. 7.
.. To se lect a menu item, turn and press t he
thumbwheel @.
Resetting values to ze ro
.. Select the on-board computer / Efficiency
program
menu item in the Vehicle func­
tions
menu .
.. Yo u can now select between the long-term
memory and s hort-term memory .
.. To reset the values in a memory, p ress a nd
hold the thumbwheel @ for one second .
The last function selected d isp lays when you
switch the ignition on .
On-board computer
You can call up the fo llowing info rmation in
the on -board computer:
- Dat e
- Dr iving t ime ( h) from the short-term memo-
ry
- Average cons umption in MPG ( l/100 km)
from the short-te rm memory
- Average speed i n mph (km/h) from the
short-te rm memory
- Dis tance driven in miles (km) from the
short-t erm memory
- Cur ren t fu e l consumption in MPG ( l/100
km)
- Short -te rm memory overview
- Long-term memory overview
T he short-te rm memory collects dr iv ing infor ­
mation from the time the ig nition is switched
on until it is switched off. If you continue driv­
i ng within two ho urs after switch ing the ig ni­
tion off, the new values are included when cal­
cu lating the c urrent t rip information .
U nli ke the short-term memory , the long-term
memory is not erased automatically . You can
select the time period for evaluating trip in-
format io n yourself . ..,.