2012 AUDI A6 lock

-Always move the passenger seat into its
rearmost position in the seat's fore and
aft adjustment range, as far away from
the airbag as possible before installing
the forward-facing child restraint. The
backrest must be adjusted to an upright
position.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched on.
.8, WARNING
Rearward-facing child restraints:
- A child in a rearward-facing child safety
seat installed on the front passenger seat will be seriously injured and can be
killed if the front airbag inflates -even
with an Advanced Airbag System.
- The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat
and child against the backrest, center
armrest, door or roof.
- Always be especially careful if you must
install a rearward facing child safety seat
on the front passenger seat in exception­
al circumstances.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched
on.
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, immedi­
ately install the rear-facing child safety
seat in a rear seating position and have
the airbag system inspected by your Audi
dealer.
Activating the convertible locking retractor
Use the convertible locking retractor to se­
cure a child restraint.
Always heed the child safety seat manufactur­
er's instructions when installing a child re-
Child Safety 181
straint in your vehicle. To activate the conver­
tible locking retractor:
.,. Place the child restraint on a seat , prefera­
bly on the rear seat.
.,. Slowly pull the belt
all the way out.
.,. Route it around or through the child re­
straint belt path
¢ A -
.,. Push the child safety seat down with your
full weight to get the safety belt really tight.
.,. Insert the belt tongue into the buckle for
that seating position .
.,. Guide the safety belt back into the retractor
until the belt lies flat and snug on the child
safety seat.
.,. You should hear a "clicking" noise as the
belt winds back into the inertia reel. Test the
convertible locking retractor by pulling on
the belt. You should no longer be able to
pull the belt out of the retractor. The con­
vertible locking retractor is now activated.
.,. Make sure that the red release button is fac­
ing away from the child restraint so that it
can be unbuckled quickly.
.,. Pull on the belt to make sure the safety belt
is properly tight and fastened so that the
seat cannot move forward or sideways more
than one inch (2.5 cm).
.8, WARNING
Using the wrong child restraint or an im­
properly installed child restraint can cause
serious personal injury or death in a crash.
- Always make sure that the safety belt re-
tractor is locked when installing a child
safety seat. An unlocked safety belt re­
tractor cannot hold the child safety seat in place during normal driving or in a
crash.
- Always buckle the child safety seat firmly
in place even if a child is not sitting in it.
A loose child safety seat can fly around
during a sudden stop or in a crash.
- Always make sure the seat backrest to
which the child restraint is installed is in
an upright position and securely latched
-
•
•

182 Child Safety
into place and cannot fold forward. Oth­
erwise, the seatback with the child safety
seat attached to it could fly forward in
the event of an accident or other emer­ gency situation .
- Always read and heed all WARNINGS
whenever using a child restrained in ave­
hicle is being used
c:;, page 168. Special
precautions apply when installing a child
safety seat on the front passenger seat
c:;, page 144, Child restraints on the front
seat -some important things to know.
Deactivating the convertible locking
retractor
The convertible locking retractor far child re­
straints will be deactivated automatically
when the belt is wound all the way back into the retractor.
• Press the red button on the safety belt
buckle . The belt tongue will pop out of the
buckle.
... Guid@ th@ safety belt all th@ way back into
its stowed position.
Always let the safety belt retract completely into its stowed position. The safety belt can
now be used as an ordinary safety belt with­
out the convertible locking retractor for child
restraints .
If the convertible locking retractor should be
activated inadvertently, the safety belt must be unfastened and guided completely back in­
to its stowed position to deactivate this fea­
ture . If the convertible locking retractor is not
deactivated, the safety belt will gradually be­
come tighter and uncomfortable to wear .
_&, WARNING
Improperly installed child safety seats in­
crease the risk of serious personal injury
and death in a collision.
- Never unfasten the safety belt to deacti­
vate the convertible locking retractor for
child restraints while the vehicle is mov- ing
. You would not be restrained and
could be seriously injured in an accident.
- Always read and heed all WARNINGS
whenever using a child restrained in ave­
hicle is being used
c:;, page 168. Special
precautions apply when installing a child
safety seat on the front passenger seat
c:;, page 144, Child restraints on the front
seat -some important things to know.
LATCH Lower
anchorages and tethers
for children
Child Restraint System anchors and how
are they related to child safety
To provide a simpler and more practicable way
to attach the child restraint on the vehicle
seat, Federal regulations require special lower anchorages in vehicles and devices on new
child restraints to attach to the vehicle ancho ­
rages.
The combination of the tether anchorages and
the lower anchorages is now generally called
the
LATCH system for "Lower Anchorages and
Tet hers for Children ."
Forward-facing child restraints manufactured
after September 1 , 1999, are required by U.S.
federal regulations to comply with new child head movement performance requirements .
These new performance requirements make a
tether necessary on most new child seats.
Installing a child restraint that requires a top
tether without one can seriously impair the
performance of the child restraint and its abil­
ity to protect the child in a collision. Installing
a child restraint that requires a top tether
without the top tether may be a violation of
state law.
Child restraint manufacturers offer LATCH
lower anchorages on their child seats with
hook-on or push -on connectors attached to
adjustable straps.
In addition to the LATCH lower anchorages,
these child restraint systems usually require .,.

184 Child Saf ety
All child restraints manu factured after Sep­
tember 1, 2002, must have lower anchorage
attachments for the
LA TCH system.
P lease remember that the lower anchorage
points are only intended for installation and
attachment of child restraints specifically cer­
tified for use w ith
LATCH l ower anchorages.
Ch ild restra ints that are not equipped with the
lower anchorage attachments can still be in­
stalled in compl iance with the child restraint
manufacturer's instruct ions on us ing vehicle
safety be lts .
A WARNING
Imprope r use of LATCH lower anchorages
can ca use se rio us pe rsonal inj ury in an ac­
cident .
- Always ca refully follow the c hild re­
st ra ints manuf acturer's inst ruct ions for
proper installa tion of the child restrain t
and proper use of t he lowe r anchorages
or safety belts in your vehicle .
- Never secure o r attach any l uggage or
other items to t he LATCH lower ancho­
rages .
- Always read and heed the important in­
formation about child restraints in this
chapter and WARNINGS ¢
page 168,
Child Safety .
Installing a child restraint with LATCH
lower anchorages
Whenever you ins tall a child restraint always
follow the child restraint manufacturer's in­
structions .
Fig. 161 Lower a nch orag es: p roper mount ing
Mounting
.,. Ma ke s ure the seatback of the rear seat
bench is in the upright posit ion and secure ly
latched in place .
.,. Attach both hook-on connectors with the
sp ring catch release on the child safety seat
onto the LATCH lower anchorage so that the
connecto rs lock into place¢
fig. 161 .
.,. Pull on the connector attachments to make
sure they are properly attached to the LATC H
lowe r ancho rage .
.,. Pull straps tight fo llow ing the child re­
s tr ain t manufacture r's instructions.
Releasing
.,. Loose n the tension on the straps following
the child restra int manufacturer's inst ruc­
tions.
.,. Dep ress the spring catches to release the
anchorage hooks from the lower anchorag­
es.
Remember: Use tether s traps to help keep the
c hi ld restra in t fi rm ly in place.
A WARNING
=
I mp roper use of the LATCH system can in -
crease the risk of serious pe rsonal injury
and death in an accident.
- These anchors were deve loped only for
child safety seats using the "LATCH" sys­
tem.
- Never attach othe r chi ld safety seats,
be lts or other objects to these anchors.
- Always make sure that you hear a click when latching the seat in place . If you do
not hear a click the seat is not secure and
could fly forward and hit the inter ior of
the vehicle, or be ejected from the vehi­
cle .
A WARNING
Imp roper installat ion of ch ild restra ints
will i ncrease the r isk of injury i n an acci­
dent.
- Always follow the child restraint system
manufacturer's inst ruct ions for proper
i n stallation of the child restra int system
-

190 Intelligent technology
ESP includes and/or works together with the
anti-lock brake system (ABS), brake assist sys ­
tem, anti-slip regulation (ASR) , e lectronic dif­
f erential lock ( ED L) and e lectronic interax le
d ifferential lock* . ESP is switched on all the
time . In certain situat ions when you need less
traction , you can switch off ASR by pressing
the button
I!] c:;, page 191 , fig. 164 . Be sure
to switch ASR on again whe n you no longe r
need less tra ct ion.
Anti-lock braking system (ABS )
ABS prevents the wheels from locking up
when braking. The vehicle can still be steered
even du ring hard b rak ing . Apply steady p res­
sure to the brake pedal. Do no t pu mp the ped­
a l. A puls ing in the b ra ke ped al ind icates that
the system is he lp ing you to b rake the vehicle .
Brake assist system
The brake assist system can decrease brak ing
d ista nce. It increases braking power w hen the
d river p resses the brake pedal quic kly in eme r­
gen cy situa tions. You mus t press and hold the
b rake peda l until the si tuation is over. In veh i­
cles with adaptive cruise control*, the brake
assist system is more sensitive if the distance
detected to the vehicle ahead is too smal l.
Anti-slip r egulation (ASR)
ASR reduces engine power when the d rive
wheels begin to spin and adapts the fo rce to
the road conditions. This makes it easier to
start, accelerat e and drive up hills .
Electronic differential lock (EDL )
The ED L brakes wheels that are spinn ing and
transfers the drive power to the o ther d rive
wheel or whee ls i f th e vehi cle is equipped with
a ll-whee l drive *. This function is available up
to about 7S mph (120 km/h).
I n extreme cases, EDL automat ica lly switches
off to help keep the brake on the braked whee l
from overheating . EDL wi ll switch on again au­
tomatically when conditions have returned to
normal.
Electronic interaxle differential lock */
selective wheel torque control*
The electronic interaxle differential lock (front
whee l drive) or the se lective whee l torque
control (all-wheel dr ive) operates when d riv­
ing t hrough curves . The front wheel on the in­
s ide of the curve or both whee ls on the inside
of the curve a re b raked select ively as needed .
T his m inimizes sliding in th e front wheels and
allows for mo re p reci se d rivi ng throug h
c ur ves . The appl icable system may not acti­
vate when dr iving in we t or snowy conditions.
_& WARNING ~
- ESP , ABS, AS R, E DL and the e lectronic in­
terax le d iffe rential lock function* cannot
overcome the laws of physics . This is es­
pecially important on slippery or wet
roads. If the systems begin acti ng to sta­
b ili ze your ve hicle , you s hould immed i­
ately c hange yo ur speed to match the
road and traffic cond itions. Do not let
t he incre ased safety provide d by the se
systems tempt you to take risks. Do ing
so will increase the r is k of a loss of vehi­
cle control, collision and serious persona l
in jur ies.
-Always adapt your speed to road, traffic and weather conditions . The risk of los­
ing control of the vehicle increases when
driving too fast, espec ially through
curves and o n slippery or wet roads, and
when dr iv ing too close to vehicles up
ahead . ESP, ABS, the brake ass ist system,
E DL, ASR and the e lectronic interax le dif­
fe ren tial lo ck fu nction * can not prevent
coll is ions.
- Always ac celerate with spe cial care on
even, smooth s urfaces such as tho se th at
ar e we t or covered with i ce and snow.
The drive wheels can spin eve n with
these assistance systems t hat cannot al­
ways he lp to red uce the risk of loss of ve -
hicle control. ..,.

206 Cleaning and protec tio n
directly at locks, or at door or hatch
openings -they can freeze shut.
- Never use sponges designed to remove insects, or any kitchen scouring sponges
or similar products . They can damage
your paint finish.
- Never use a dry cloth or sponge to clean
the headlights . Only use wet cloths or
sponges to prevent scratches. It is best
to use soapy water.
- You should remove debris (such as in­
sects) from the headl ight lenses on a
regular basis, for example when refuel­
i ng your vehicle. Never clean the head­
li ghts w ith a dry cloth or sponge. Use a
wet cloth or sponge.
It is best to use
soapy wa ter.
@ For the sake of the environment
In the interest of the envi ronment, the ve­
hicle sho uld only be washed i n special
was h bays.
Washing your vehicle with a power
washer
Cleaning the exterior of your car with a high­
pressure power washer is safe as long as you
observe a few simple rules.
.. Befo re using the power washer , make sure
yo u have read and understood the WARN­
INGS¢
A in General information on
page 204.
.. Always fo llow the operating instructions for
the power washer .
.. Make sure that the jet o n the spray hose
produces a "fan shaped spray" .
.. Do
not hold the spray nozzle too close to
soft materia ls .
When cleaning the veh icle with a power wash­
er
always follow the operating instructions .
This applies particularly to the
op erating
pr essure
a nd the s pray ing di stance . Keep a
d ista nce from soft materials such as rubber
hoses o r insulat ing ma ter ial as well as sensors
and camera lenses . Do not use a jet which sprays water in a
d
ir ect
stream
or one t hat has a rotating jet .
Water temper ature sho uld not ex ceed 140 °F
(60 °().
A WARNING ~ -
Neve r wash tires with a jet that sprays wa­
ter i n a direct stream. This could cause in ­
vis ib le damage to the t ires and weaken
them, even if the spray is from a re lative ly
l ong distance and for a short time. Dam­
aged and weakened tires can fail and cause
accidents and personal inj ury.
'
([) Note
To avoid damaging your vehicle, a lways
make sure that there is suffic ient d istance
between the spray head and soft materia ls
like rubber hoses, plast ic pa rts and sound­
deaden ing mater ials as w ell as sensors
and camera lenses. Neve r aim t he sp ray
head at the same point for a long time.
This also applies to cleaning headligh ts
and painted bumpers. Remembe r: the
closer the nozzle is to the surface of the
materia l, the greater the stress on the ma ­
terial.
Sensors and camera lenses
- Remove snow with a hand br ush and remove
ice with a de- ic ing spray that does not con­
tain so lvents .
- Clea n the sensors (adaptive cruise control*,
pa rk ing system*) w ith a cleaning so lution
that does not contain so lvents and a soft
cloth .
- The camera lens or the area in front of the
came ra le ns is no rmally cleaned by the
w indshie ld w ipers o r he adlig ht wipers (night
vision system *).
If the lens or the area is ex­
ceptionally di rty, clean the area wit h glass
cleaner and a soft, dry cloth .
(D Note
-If you was h your veh icle with a pres sure
washer,

210 Cleaning and protec tio n
-Always read and heed all WARNINGS and
other information
c> page 204.
Exhaust tail pipes
Road salt and other corrosive materials will
damage the material in the exhaust tail pipes
if they are not cleaned regularly . Do not clean
the tail p ipes with wheel cleaner, paint pol ish,
chrome po lish or other abrasive cleaners.
C lean the tail p ipes with car ca re p roducts
that are su itable for stain less stee l.
Your author ized Audi dealer can provide clean­
ing p roducts that have been tested and ap­
p roved fo r you r vehicle.
Care of interior
Infotainment components
The MMI/RSE* display may be cleaned with a
soft cloth and commercially-ava ilable "LCD
cleaner" . The cloth should be coated lightly
when the clean ing solution when cleaning the
d isplay.
The MMI/RSE* contro ls must be cleaned first
with a brush so t hat dirt does not ente r the
un it or enter between the buttons and the
housing. Then wiping the controls with a cloth
dampened with dish detergent and water is recommended.
CJ) Note
- To avoid sc ratch ing the disp lay, you
shou ld never clean it dry.
- To prevent damage, ma ke sure fluids do
not enter the controls.
Aluminum trim
Use only n eutral-pH products to remove spots
and deposits from aluminum surfaces.
Chrome ca re products and alkaline cleaners
will attack aluminum s urfaces and can dam­
age them over time.
A WARNING
A lways read and heed all WARNINGS and
other information
c> page 204.
Fabrics and fabric coverings
Fabr ics and fabric cover ings (e .g. seats, door
trim panels, etc.) should be cleaned at regular i ntervals w ith a vacuum cleaner. This removes
su rface di rt particles which could become em ­
bedded in the fabri c through use. Steam
cleaners should not be used, because the
steam tends to p ush the dirt deeper into the
fabric and lock it there.
Normal clean ing
Generally, we recommend using a soft sponge
o r a lint-free microfiber clo th to the clean fab­
ric. Brushes shou ld only be used for carpets
and floor mats, since other fabric surfaces
could be harmed by brushes.
Norma l su rface stains can be cleaned using a
commercially available foam cleaner . Spread
the foam on the s urface of the fabric with a
soft sponge and work it in gently. Do not satu­
rate the fabric. Then pat the foam dry using
absorbent, dry cloths (e.g. m icrof iber cloth)
and vacuum it after it has dried completely.
Cle anin g sta ins
Stains caused by beverages (e .g. coffee, fruit
juice, etc.) can be treated with a mild deter­
gent solution. Apply the detergent solution
with a sponge. In the case of stubborn stains, a detergent paste can be applied directly to
the stain and worked into the fabric. After­
wards, use copious amounts of clean water to
remove the rema in ing deterge nt. Apply the
water wit h a damp clo th or sponge an d pat
the fabric dry with an abso rbent, dry cloth .
Stains from choco late or makeup should have
detergent paste (e.g. ox-gall soap) rubbed in­
to them. Afterwa rds, remove the soap with
water (damp sponge) .
Alcohol can be used to treat stains from grease, o il, lipstick or a ballpoin t pen . Melted ..,.

212 Cleaning and protec tio n
Care and handling
Because of the exclusive nat ure of the types of
l eather that Audi uses and their unique prop ­
erties (such as sensitivity to oils, grease, soi l­
ing, etc.), you will need to be somewhat care­
fu l w ith these leathers, and a certain type of
care is required. For examp le, dark cloth ing
materials can d iscolor leather seats (especial­
ly if such cloth ing is damp and was not dyed
correctly). Dust and dirt part icles in pores,
folds, and seams can have an ab ras ive effect
and can damage the leather surface as well as
weaken seams.
The leather should be cleaned regularly as
needed. After having been used for a re latively
long t ime, your leather sea ts will acquire a
rich aged finish. This is a characteristic of nat­
ura l leather and a sign of true quality .
I n o rder to maintain the va lue of t his natura l
p rod uct over the life of your vehicle, you
should follow the recommendations below :
(D Note
-To keep you r leather from bleaching out,
do not a llow it to be exposed to bright
sunl ight for long periods of time. If you
have to leave the vehicle parked o utside
for long periods, cover the leather to
protect it from d irect exposure to sun­
li ght.
- Sharp objects on clothing, such as zip­
pers, rivets or sharp pieces on be lts can
l eave permanent scratches or scrape
marks on the surface of the leather.
- After each t ime you clean the leather and
at regu lar intervals, use a leather preser­
vat ive creme that conta ins UV-blockers
and that works into the leather. This
creme wi ll nourish and moistur ize the
l eather, helping it to b reath e and stay
supple.
It also helps to bu ild up a protec­
tive coat ing on the s urface.
- Clean t he leather every 2 -3 mont hs,
and clean a ny areas that get soiled. - Remove fresh marks made by ballpo
int
pens, ink, lipstick, shoe polish, etc. as
soon as poss ible.
- Preserve the color of the leather as need­
ed by using a specia l co lored leather care
creme to touch up areas of uneven color.
Cleaning and caring for leather
upholstery and trim
Applies to vehicles: with natural leather
Natural leather requires special care and a t­
tention .
Normal cl eaning
.. Clean soiled areas with a slightly moistened
cotton or woo len cloth .
More stubborn dirt
.. More s tubbor n dirt can be removed using a
cloth sa turated wi th a mild soap solut ion (2
tablespoons mild liquid soap).
.. Never allow the soap sol ution to saturate
the leath er, and make certain that no water
soak s into the seam s.
.. Wipe off the soap solution with a soft, dry
cloth .
Cleanin g spot s
.. Remove fresh wate r-based spots (s uch as
coffee, tea, juices, blood) with an absorbent
cloth or paper towel.
.. Remove fresh
grease or oil -based spots
(such as butte r, mayonnaise, chocolate) with
an absorbent cloth or paper towel, or use
the cleaner from the leather care kit if the
spo t has no t yet penetrated i nto t he surface
of the leathe r .
.. Use an oil/grease d issolving spray, if
oil /
grea se spot s ha ve d ried on.
.. Remove specific k inds of spots (ballpoint
pen, fe lt marker, fingerna il polish, water­
based pa int, shoe polish, etc.) with a spot
remover specifically formu lated for lea ther.
L e athe r care
.. Every half year use an approved leather care
product (available from your Audi dealer) to
care for the leather . .,.

214 Cleaning and protection
-When cleaning your safety belts, inspect
them for damage.
If you discover dam­
age, see your Audi dealer .
- Always read and heed all WARNINGS and
other information
c> page 204.
Engine compartment
Be especially careful when cleaning the en­
gine compartment.
Always switch off the ignition before clean­
ing the engine
c> .&..
Plenum panel
Remove leaves from the plenum pane l in front
of the windsh ield under the engine compart­
ment. This prevents the water dra in ho les
from becoming blocked, and it prevents de­
bris from entering the vehicle interior through
the heating and venti lation ducts .
Corrosion protection
The engine compartment and transmission
have been corrosion -protected at the factory.
Good ant i-corrosion treatment is very impor­
tant, particularly in the winter. If the veh icle
is frequent ly driven on salt treated roads , the
enti re engine compartment and plenum panel
should be tho roughly cleaned at the end of
winter and retreated to prevent sa lt damage.
At the same time, the underside of the vehicle
should be washed as we ll.
If the engine compartment is cleaned at any
time with grease removing solutions
1l, or if
you have the engine washed, the anti-corro­ sion treatment is a lmost always removed as
well. It is therefore essential to have a long­ lasting corrosion protection reapplied to all
surfaces, seams, joints and components in the
engine compartment .
1l Use o nly the co rrect cle anin g so lu ti on s. Ne ver use gas­
o lin e or d ie se l fuel.
A WARNING
Be aware: The eng ine compartment of any
motor vehicle is a potentially hazardous
area .
- Before work ing in the engine compart­
ment, be sure to read the information
c> page 220.
-Before reach ing into the front panel, al ­
ways sw itch off the ignition . Otherwise,
the windshield wiper system could unin­
tentionally be switched on, possibly
causing personal injury from the moving
wiper linkage .
- Never reach into the area around or
touch the radiator fan. The auxiliary fan
is temperature controlled and can sw itch
on suddenly -even when the ignition is
off.
- Do not wash, wax or dry the engine with
the engine running . Moving or hot parts
could injure you.
- Do not clean the underside of the chas­
sis, fenders, wheel covers, or other hard
to reach parts without protecting your hands and arms . You may cut yourself on
sharp-edged metal parts.
-Always read and heed all WARNINGS and
other information
c> page 204.