2012 AUDI A6 fuel

-When you leave the vehicle, always take
the ignition key with you. This will pre­
vent passengers (children, for example)
from accidentally being locked in the ve­ hicle should they accidentally press the
power locking switch in the doors .
- Do not leave children inside the vehicle
unsupervised. In an emergency it would
be impossible to open the doors from
the outside without the key.
- Applies to vehicles with power side door
closer*:
- When closing a door, make sure noth­
ing can interfere with the door. This
could cause serious personal injury.
- You can stop the door from closing at
any time by pulling on the inside or
outside door handle .
@ Tips
-In the event of a crash with airbag de­
ployment all locked doors will be auto­
matically unlocked to give access to the
vehicle occupants from the outside.
- If the power locking system should mal­
function, you can lock the driver's door
using the mechanical key¢
page 36 .
-If the power locking system should fail,
you can still open the fuel tank flap in an
emergency ¢
page 218.
-You are well advised not to keep valua ­
bles inside an unattended vehicle, visible
or not . Even a properly locked vehicle
cannot provide the security of a safe .
- If the LED in the upper edge of the driv­
er's door panel comes on for about 30
seconds after the vehicle is locked, there
is a malfunction in the power locking or
the anti-theft warning system. Have the
malfunction corrected by an authorized
Audi dealership or qualified repair facili­
ty.
Opening and closing 33
Setting power locking
T he driver can determine the functions for
power locking in the MMI .
.,. Select: !CAR !function button> Car systems
control bu tton > Vehicle settings > Central
lo cking .
Unlock doors -
You can decide if All doors or
only the
Dri ver should unlock. The rear lid al­
so unlocks when
All is selected . If you select
Driver in a vehicle with a convenience key* ,
only the door whose handle you pull will un­
lock.
If you select
Driver , all the doors and rear lid
will unlock if you press the
ffi button on the re­
mote control master key twice .
Lock exterior trunk handle -If you selec t On,
the rear lid handle is locked . In this case the
rear lid can be opened with the button
a on
the master key or with the
a button in the
driver's door . In vehicles with a convenience
key* , you can still open the rear lid using the
handle if an authorized master key is near the
proximity sensor .
Fold mirrors* -If you select On, the exterior
rearview mirrors fold in automatically when
you press the
(TI button on the remote contro l
master key or touch the sensor* in the handle .
Lock when driving -If you select On, the vehi ­
cle locks automatically when driving. All of
the doors and rear lid lock.
Tone when locking -When you select On, a
confirmation tone sounds when you lock the
vehicle.

58 Seats and storage
for your vehicle. Contact the nearest Audi
dealer for information on approved modu lar
roof racks for your vehicle.
- Only use roof racks approved for your vehi­
cle. These approved roof racks are the basis
for a complete roof rack system. Additional
attachments or carrier systems are needed
to transport luggage and sports equipment.
We recommend using roof racks from the
Audi original accessories program.
- The support feet of the roof rack must al­
ways be installed in the holes in the roof
frame ¢
fig. 59. The holes are only visible
when the doors are open. In the case of roof
racks with pins, the pins must be secured in
the holes during assembly.
- We recommend that you keep the installa­
t io n instructions for your roof rack system
together with your Owner's literature in the
vehicle.
When should the roof rack be removed?
-Before going through an automatic car wash
(it is best to ask the car wash operator for
advice).
- When not in use, to reduce fuel consump­
t io n, w ind no ise and to guard against theft.
.&_ WARNING i.c
-Use of an unapproved roof rack or incor-
rect mounting of an approved roof rack
can cause the roof rack or the items at­
tached to it to fall off the roof onto the
road.
- Objects fall ing from the roof of a vehicle
can cause a crash and personal injury.
- Only mount the roof rack on the desig­
nated locations on the roof¢
fig. 59.
-The roof rack system must be installed
exactly according to the instructions pro­
vided.
- When driving w ith a roof rack system,
changes to the center of gravity and wind
resistance can change the veh icle han­
dling and lead to a collision . Always
adapt your driving and your speed to the
current conditions.
(D Note
- Your vehicle warranty does not cover any
damages to the vehicle caused by using
roof racks or mounting structures not
approved by Audi for your veh icle. The
same applies to damage resulting from
incorrect roof rack installation.
- Always check the roof rack mountings
and hardware before each trip and dur­
ing a trip to make sure everyth ing is se­
curely tightened.
If necessary, retighten
the mountings and check the entire sys­
tem from time to time.
- After mounting a roof rack system, or
when you transport objects on the roof
o f you r vehicle, the height of the vehicle
is naturally increased . Be careful when
driving under low bridges or in parking
garages for example. This cou ld cause
damage to the load and even the vehicle
itself.
- Make sure the open rear lid and the sun­
roof* do not come into contact with the
roof rack.
Loading the roof rack
Always distribute loads evenly. Make sure
anything on the roof rack is securely tied
down.
.,. Always distribute the loads on the roof rack
even ly.
.,. Always attach items to the roof rack secure-
ly before you drive off.
The maximum permissible roof weight is
220
lb (100 kg).
The roof weight is the total of
the weight of the roof rack, the attachments
and the cargo you are carrying. You must also
not exceed the maximum load weight for the
roof rack you are using.
When using a roof rack system which has a
lower load carrying capacity, you must not use
up the total maximum permissible load carry­
ing capacity specified above. Instead, you
should load the roof rack system only to the .,..

maximum capacity specified by the
manufacturer of the roof rack system.
A WARNING
Weak, damaged or improper straps used
to secure items to the roof rack can fail during hard braking or in a collision and
cause serious personal injury .
- Make sure the roof rack is installed exact­
ly as specified above¢
page 57 .
- Always use suitable mounting straps for
securing items to the roof rack to help
prevent items from shifting or fly ing for ­
ward.
- Items on the roof rack must always be
securely mounted.
- The use of a roof rack can negatively af­
fect the way a vehicle handles . Cargo
that is large, heavy, bulky, long or flat
will have a greater negative influence on
the vehicle's aerodynamics, center of
gravity and overall handling . Always
dr ive slowly, avoid sudden braking and
maneuvers when transpo rting cargo on
the roof of your vehicle.
- Never exceed the maximum permissible
load carrying capacity of the roof of your
vehicle , the permissib le axle weights and
the permissible total weight of your veh i­
cle ¢
page 274, Weights.
-Always drive slowly, avoid sudden brak­
ing and maneuvers when transporting
cargo on the roof of your vehicle .
@) For the sake of the environment
Sometimes it may be easier to leave a roof
rack insta lled even though you are not us­
ing it . Due to the increased air resistance
your veh icle will unnecessar ily use more
fuel. Remove the roof rack if you are not
going to use it .
.
Sea ts a nd s to rage 59
Luggage compartment
Loading luggage compartment
Items of luggage must be stowed securely.
Fig. 60 Pla ce hea vy o bject s as far forward a s possible .
Note the following to preserve the vehicle's
good handling charac teristics.
.,.. Distribute the load as evenly as possible .
... Place heavy objects as far forward as poss i­
ble ¢
fig. 60 .
... Secure the items of luggage w ith the cargo
net* or w ith non -elastic retaining straps to
the tie-down rings * ¢
page 61.
A WARNING
- Loose objects in the l uggage compart­
ment can slide about suddenly and a lter
the vehicle's handling characteristics.
- Loose objects in the passenger compart­
ment can fly forward during abr upt ma­
neuvers or accidents and injure occu­
pants .
- Always store objects in the luggage com­
partment and use suitable straps, partic­
ularly with heavy objects .
-
-When you transport heavy objects, al­
ways remember that a change in the cen ­
ter of gravity may result in a change in
the vehicle's handling characteristics.
- Follow all warnings¢
page 123, Driving
Safely .
(D Tips
The tire pressure must be ad justed to the
load - see the t ire pressure sticker located
on the dr iver's side B -pillar .

Automatic Transmission
multitronic ®
Introduction
Appl ies to vehicles: with multitr oni c
Your veh icle is equipped with an electronically
controlled,
continuously variable transmis­
sion
(multitronic ®). In contrast to convention ­
al automatic transmi ssions using shifting op­
erations, the transmission ratio in the contin­
uously variab le transmission is changed con ­
tinuously. This optimizes the comfort level
and conserves fuel.
The gear ratio in the transmission is selected
(upshift and downshift) completely automati­
cally as a function of the defined driving pro­
grams.
If desired, the driver can also select the gears
manually (tiptronic mode).
Instead of the torque converter in convention­
al automatic transmissions, your multitronic ®
transmission uses a multidisk clutch for pow­
er transmission . Therefore, the "creep behav­
ior" of the veh icle dur ing idling when tempo­
rarily stopped in selecto r lever pos it ion 0/S or
R is less pronounced.
Driving the automatic transmission
A ppl ies to vehicles: with multitr onic
Fig . 105 Shift gate on the cente r console: se lecto r lev­
er wi th release button
Starting the engine
• The selector leve r must be in P or N. Automatic Transmission 101
Starting off
•
Press and hold the brake pedal.
• Press and hold the re lease button in these­
lector lever handle and move the selector
lever from
P or N to D/S and release the but­
ton
c:> _&. .
.,. Wait briefly until the transmission has shift­
ed (you will feel a slight movement) .
.,. Remove your foot from the brake pedal and
accelerate .
Rocking back and forth to become
unstuck
.,. Shift only between D/S and R when the ve ­
hicle is at a full stop and the engine is run­
ni ng at idle speed .
Stopping
.,. Press and hold the brake pedal until the ve­
hicle has come to a complete stop .
• Keep the brake pedal depressed so that the
veh icle cannot roll forward or backward
while it is idling
c:> _&. .
• Once stopped, do not depress the acce le ra­
tor peda l to rev up the engine
c:> _&. .
Parking
.,. Press and hold the brake pedal until the ve­
hicle has come to a complete stop .
• Set the park ing brake firmly
c:> page 7 4,
Parking .
• Press and hold the release button in these ­
lector lever handle, move the se lector lever
into
P and then let go of the release button
c:> _&..
The selector lever must be in P or N. If one of
the driving positions is engaged a safety
switch will prevent the eng ine from being
started . See also co
page 70.
Before you move the selector lever from the
P
position, you must always app ly the brake
pedal before and while depressing the button
in the handle of the selector lever.
A WARNING
-- Unintended vehicle movement can cause
serious injury.

Manual shift program
Applies to vehicles: with multitronic
Using the manual shift program you can
manually select gears .
Fig. 108 Center console: shi ftin g th e tip tronic ma nua l·
l y
Fig. 109 Display: man ual sh ift program, selected gea r
highl ighted
Switching to manual shift program
• Push the selector lever to the right from 0/
5 . As soon as the transmission has switched
over, the selected gear appears in the dis­
play.
To upshift
• Push the selector lever forward to the plus
pos ition
0 ~ fig . 108 .
To downshift
• Push the leve r to the minus position 0 -
When accelerating , the transmission will au­
tomatically shift into the next gear before the
engine reaches its maximum RPM .
If you apply a light throttle when accelerat­
ing, tiptron ic will automatically shift from 1st
to 2nd gear to save fuel. If you apply a heavy
thrott le, the transmission will stay in 1st gear
Automatic Transmission 105
until near maximum RPM is reached, or until
the driver shifts into 2nd gear.
If you take your foot off the accelerator pedal
when d riving down a steep incline, tiptronic
will downshift from the selected gear into the
next lower gear until it reaches 1st gear,
based on road speed and engine RPM. Auto­
matic downshifting is interrupted as soon as
you apply the throttle again.
(D Tips
- When you shift into the next lower gear,
the transmission will downshift only
when there is no possibility of over-rev­
ving the engine.
- When the kick-down comes on, the
transm ission w ill shift down to a lower
gear, depending on vehicle and engine
speeds .
- tiptronic is inoperative when the trans­
mission is in the fai l-safe mode.
Steer ing wheel with tiptronic
Applies to vehicles: with tiptronic steering wheel
The shi~ buttons on the steering wheel allow
the driver to shift gears manually.
Fig. 1 10 Steer ing w hee l: S hift bu ttons
• To downshift, touch the button on the left
0 -
• To upshift, touch the button on the right
0.
The shift buttons are activated when these­
lector lever is in
D/S or in the manual shift
program (tiptronic) .

110 Autom atic Tran smi ssi on
Dynamic shift program (DSP)
Appli es to vehicles: with tiptronic
The automatic transmission is electronically
controlled .
The transmission is self adapting and will au­
t oma tically
select the best shift program suit­
ed to the driving conditions and driving style .
The transmission will se lect one of the
econo ­
my programs when you drive at a steady
speed or a gradually changing speed without
heavy acceleration . This achieves optimum
fuel efficiency, with early upsh ifting and de­
layed downshifting.
The transmission will automatically select the
s po rty shift programs when you drive at high­
er speeds, or w ith heavy acceleration and fre­
quent ly changing speeds. Upshifts are de layed
to make f ull use of eng ine power. Downsh ift­
i ng takes p lace at higher engine speeds than
in the economy programs.
The se lection of the most suitable shift p ro­
gram is a cont inuous, automati c process. The
driver can also make the t ransmission switch
to a sporty prog ram by
quic kly pressing down
the gas pedal.
This causes the transmission to shift down to
a lower gear to achieve rap id acceleration, e.g.
for qu ickly passing another veh icle. You do not
need to press the gas peda l into the kick-down
range. After the transmission has upshifted,
the original program is selected according to
your driving style.
An additional shift program allows the auto­matic transmission to select the proper gear
for uphill and downhill gradients.
This keeps the transmission from shifting up
a nd down unnecessari ly on hills. The trans­
mission will shift down to a lower gear when
the driver presses the brake pedal on a down­
h ill gradient. This makes use of the braking ef­
fect of the eng ine without the need to shift
down manually .
Manual shift program
Applies to vehicles: wit h tiptronic
Using the manual shift program you can
manually select gears .
Fig . 115 Center conso le: sh ift ing the t iptron ic ma nual ­
l y
Fig . 1 16 D isp lay: manual sh ift prog ra m , se lected gear
hi ghlighted
Switching to manual shift program
.,. Push the selector lever to the rig ht from D/
5 . As soon as the transmission has sw itched
over, the se lected gear appears in the dis­
p lay.
To u pshift
.,. Push the selector lever forward to the plus
position
0 ¢ fig .. 115 .
To down shift
.,. Push the lever to the minus pos ition 0 -
When accelerating, the transmission will au­
tomatica lly shift into the next gear before the
engine reaches its maximum RPM.
If you apply a light throttle whe n accelerat-
ing, tiptronic wi ll automatically shift from 1st
to 2nd gear to save fuel. If you apply a heavy
throttle, the transmission wi ll stay in 1st gear .,.

196 Driving and environment
Driving and
environment
The first 1,000 miles
(1,500 km) and
afterwards
New engine
The engine needs to be run-in during the first
1,000 miles (1,500 km).
For the fir st 600 miles (1,000
kilometers ):
.,. Do not use full throttle.
... Do not drive at engine speeds that are more
than 2/3 of the max imum permitted RPM.
... Avoid hig h engine speeds.
From 600 to 1,000 mile s (1 ,000 to
1,500 kilometers):
... Speeds can gradually be increased to the
max imum pe rm iss ible road or eng ine speed .
During and after break-in per iod
.,. Do not rev the engine up to high speeds
when it is cold. Th is app lies whether the
transm ission is i n N (Neutra l) or in gear.
After the break-in period
... Do not exceed maximum engine speed un­
der any circumstances.
.,. Upshift into the next hig her gear
before
reaching the red area at the end of the tach­
ometer scale
c:> page 11.
During the first few hours of driving, the en­
g ine's interna l friction is higher than later
when all the moving parts have been broken
in . How well this break- in p rocess is do ne de­
pends to a conside rable extent on th e way the
ve hicl e is driven d uring the first 1,0 00 miles
(1, 500 k ilome ters).
0 Note
E xtremely high engi ne speeds are auto­
mat ica lly reduced. However, these rpm
lim its are progr amme d for an engine well
r u n- in, not a new engine .
{® For the sake of the environment
Do not drive with unnecessarily high en­
g ine speeds - upshifting ear ly saves fuel,
reduces no ise and protects the environ­
ment.
, New tires
If your vehicle is runni ng on new tires, drive
part icularly caref ul for the first 350 miles
(500 kilomete rs) afte r fitt ing .
A WARNING
New tires tend to be sl ippery and mus t al­
so be "broken -in" . Be s ure to remember
this dur ing the fi rst 350 mi les ( 500 kilo ­
meters) . Brake gently . Avoid fo llow ing
closely behind other vehicles or other sit­
uations that m ight require sudden, hard
braking .
New brake pads
Remember that new brake pads do not have a
full bra king effect dur ing the fi rst 250 m iles
(400 kilomete rs) afte r they a re insta lled .
New brake pads have to be "burnished in" be­
fo re t hey have optima l grab
c:> A .
During the break- in period, you should avoid
putting severe loads on the brakes. Severe
l oads include, for example, sudden hard brak­
i ng, in particular at very high speeds or, for
example, on mounta in passes .
A WARNING
New b rake pa ds don't have t he bes t stop­
pi ng power and mus t be "broke n-in " dur­
i ng the in iti al 1 00 to 150 mi les (150 to
20 0 k ilometers) of no rma l city driving . You
can compensate for this by pressing the
br ake peda l mo re f irm ly . This also applies
l ater when new pads are installed.

Catalytic converter
It is very important that your emission con­trol system (catalytic converter) is function­
ing properly to ensure that your vehicle is run­
ning in an environmentally sound manner .
.. Always use lead-free gasoline¢ page 215,
Fuel supply.
.,. Never run the tank down all the way to
empty.
.,. Never put too much motor oil in your en-
gine
¢ page 225, Adding engine oil~-
.,. Never try to push- or tow-start your veh icle.
The catalytic converter is an eff icient "clean­
up" device built into the exhaust system of
the vehicle . The catalytic converter burns
many of the pollutants in the exhaust gas be ­
fore they are released into the atmosphere.
The exclusive use of unleaded fuel is critically
importa nt for the life of the cata lytic convert­
e r and proper functioning of the engine.
A WARNING
-
- Do not park or operate the vehicle in
areas where the hot exhaust system may
come in contact with dry grass, brush,
fuel spill or other material which can cause a fire.
- Do not apply additional undercoating or
rustproofing on or near the exhaust
man ifold, exhaust pipes, catalytic con­
verter or heat shields. During driving, the
substance used for undercoating cou ld
overheat and cause a fire.
0 Note
- Be aware that just one tank filling with
leaded fuel will already seriously de­
grade the performance of the catalytic
converter.
- Do not exceed the correct engine oil level
¢ page 225.
-Do not drive until the fuel tank becomes
completely empty. The eng ine could mis­
fire . U nburned fuel could a lso get i nto
Dri vin g and en vironm ent 197
the exhaust system and this cou ld cause
the catalytic converter to overheat .
- Do not swi tch off the ignit ion while the
vehicle is mov ing.
- Do not continue to ope rate your veh icle
unde r these conditions, as othe rwise fuel
can reach the catalytic converter. This
co uld result in overheating o f the con­
verter, requir ing its replacement .
- To assure efficient operation of the Emis ­
sion Control System:
- H ave your vehicle maintained prope rly
and in accordance w ith the se rv ice rec­
ommendat ions in you r Warranty &
M aintenance boo klet.
- L ack of prope r maintenance as we ll as
improper use of the vehi cle w il l impair
the function of the em ission contro l
system and could lead to damage .
@ For the sake of the environment
Even when the Emiss ion Control System is
operat ing properly, the exha ust gas can
have a sul fur -li ke exhaust gas smell under
some operating states . This depends on
the sulfur content of the fuel being used .
Using a different brand of fue l may help,
or filling the tank with lead-free super
grade gasoline .
Avoid damaging the
vehicle
When you are drivi ng on poo r roads, or over
c ur bs, s teep ramps, etc., ma ke certai n that
low -lying parts s uch as spoilers and exhaust
system pa rts do not bottom o ut and get dam­
aged.
T h is is espec ially true for veh icles w ith low­
s lung chassis (spor ts chassis)* and fully load­
ed vehicles. •
•