2012 AUDI A6 buttons

66 Warm and cold
Four-zone automatic climate control
Operation
Applies to vehicles: with four -zone automatic climate control
We recommend pressing the IAUTO I button and setting the temperature to 72 °F (22 °C).
Fig. 67 Four-zone automat ic climate contro l: controls
Fig . 68 Fou r-zone automatic cl imate cont rol: rear con ·
trol s
Press the buttons to turn the functions on or
off. Use the dials to adjust the temperature,
the blower speed and the air distribution. The
LED in a button will light up when the func­
tion is switched on. The settings are shown in
the climate control display and are also shown in the MMI display for a few seconds . The driv­
er and front passenger sett ings can be adjust­
ing separately.
The settings can also be adjusted in the rear
<::;> fig. 68.
IOFF j Switching the climate control
system on/off
The I O FFI button switches the climate control
system on or off .
It also switches on when you
turn the dia l or press any button . Airflow from outside is blocked when the
climate control
system is switched off .
You can activate the residual heat f unction
whe n the ignition is off by pressing and hold­
ing the ~ button. The residua l heat from the
coolant is used to heat the vehicle interior .
The residual heat function switches off auto­
matically after about 30 minutes.
!ACI Switching cooling mode on/off
The air is not cooled and humidity is not re­
moved when cooling mode is switched off.
This can cause fog on the windows. Cooling
mode switches off automatically when the
outside temperature is below zero .
1-1 Switching recirculation mode on/off
In recirculation mode, the air inside the vehi ­
cle is circ ulated and filtered. This prevents the
unfiltered air outside the vehicle from enter­
ing the vehicle interior . We recommend
switching recirculation mode on when driving
through a tunnel or when sitting in traffic ¢ .&, .
The
! AUTO I button or~ button switches rec i r-
cu lation mode off. .,.

Adaptive cruise control and braking guard 81
Setting the speed and activating
regulation
~ To set the current speed, press the !SET !
button ¢ fig. 81. The set speed is shown in
the tachometer @and in the display
¢
fig . 82. You must also press the brake
pedal when the vehicle is stopped .
Switching adaptive cruise control off
~ Push the lever away from you into position
@ until it clicks into p lace. The message
ACC off appears.
Indicator lamps and messages in the instru­
ment cluster display inform you about the cur ­
rent system status and settings.
@ Indicator lights
Pl -adaptive cruise control is switched on. No
vehicles are detected up ahead . The stored
speed is ma intained.
I -A moving vehicle is detected up ahead.
The adaptive cruise control system regulates
the speed and distance to the moving vehicle
ahead and acce lerates/brakes automatica lly.
Mi -adaptive cruise control is swit ched on. A
moving vehicle up ahead was detected . Your
vehicle remains stopped and will not start
driving automatically.
I -When automat ic brakin g is not able to
keep enough distance to a previously detected
moving vehicle up ahead, you must take con ­
trol and brake¢
page 82, Prompt for driver
intervention.
© Display
If adaptive cruise control is not shown in the
disp lay, you can call it up with the multifunc ­
tion steering wheel buttons
¢page 23.
Based on the symbo ls in the display, you can
determine if the system is maintaining a dis­
tance to the vehicle ahead and what that dis­
tance is .
No vehicle -No veh icle ahead was detected.
White vehicle -A vehicle ahead was detected .
Red vehicle -Prompt for the driver to take ac­
tion ¢
page 82.
Both arrows on the scale© indicate the dis­
tance to the vehicle ahead. No arrow appears
when the vehicle is on an open road and there
is no object ahead. If an object is detected
ahead, the arrow moves on the scale.
T he green zone on the scale shows the stored
distance . For information on changing the
stored distance ¢
page 83. If the distance
selected is too close or may soon become too
close, the arrows move into the red zone on
the scale .
A WARNING
Improper use of the adaptive cruise con­
trol can cause collisions, other accidents
and serious personal injur ies.
- Pressing the
! SET ! button when driv ing at
speeds below
20 mph (30 km/h), will au­
tomatically accelerate the vehicle to
20
mph (30 km/h), which is the minimum
speed that can be set.
(D Tips
-If you switch the ignit ion or the adaptive
cruise control off, the set speed is erased
from the system memory.
- You cannot switch the Electronic Stabili­
zation Program (ESP) to the SPORT mode
w hen adaptive cruise control is switched
on.
Driving in stop-and-go traffic
Applies to veh icles: w ith adaptive c ruise control
The adaptive cruise contro l system also as­
sists you in stop-and-go traffic. If a previous
detected vehicle ahead stops, your veh icle will
brake to a stop, within the limits of the sys­
tem .
~ To resume driving with adaptive cruise con­
trol, tap the acce lerator pedal or
~ Pull the lever toward you into position @
¢ page 80, fig. 81. ..,_

Night vision assistant
Night vision assistant
with detected pedestrian marking
Description
App lies to vehicles: with night v isio n assistant
Fig . 97 D isplay: n ight vision ass istant
"Night v is ion assistant with pedestrian detec­
tion" uses an infrared camera to monitor the
area in front of your vehicle at night. Within
the limits of the system, it can display objects
up to about 1000 feet (300 meters) away. The
heat image of a pedestrian detected by the
camera is shown in the instrument cluster dis­
play
Q fig . 97 . Warm areas appear lighter and
cold areas appear darker .
Pedestrian detection
Applies to vehicles: with n ig ht v ision ass istant
F ig. 98 Display : yellow pedest rian mark in g
Night vision assistant 97
Fig. 99 Display: symbol when infrared image is not
visible
Night vision assistant can detect pedestrians
that are between about 50 and 300 feet (15
and 90 meters) in front of the vehicle, under
ideal conditions . If a pedestrian is detected
when it is dark outside and the vehicle head­
lights are switched on, the pedestrian is high­
l ighted in yellow
Q fig . 98, Q page 98, Gen­
eral information .
If another display such as
navigation replaces the image from the night
vision assistant , the symbo l~,, appears in a
tab
r::',> fig . 99.
(D Tips
If the night vision assistant image does
not appear when the system is switched
on, you can access it with the buttons on
the m ultifunction steering wheel
¢pa ge 24.

Manual shift program
Applies to vehicles: with multitronic
Using the manual shift program you can
manually select gears .
Fig. 108 Center console: shi ftin g th e tip tronic ma nua l·
l y
Fig. 109 Display: man ual sh ift program, selected gea r
highl ighted
Switching to manual shift program
• Push the selector lever to the right from 0/
5 . As soon as the transmission has switched
over, the selected gear appears in the dis­
play.
To upshift
• Push the selector lever forward to the plus
pos ition
0 ~ fig . 108 .
To downshift
• Push the leve r to the minus position 0 -
When accelerating , the transmission will au­
tomatically shift into the next gear before the
engine reaches its maximum RPM .
If you apply a light throttle when accelerat­
ing, tiptron ic will automatically shift from 1st
to 2nd gear to save fuel. If you apply a heavy
thrott le, the transmission will stay in 1st gear
Automatic Transmission 105
until near maximum RPM is reached, or until
the driver shifts into 2nd gear.
If you take your foot off the accelerator pedal
when d riving down a steep incline, tiptronic
will downshift from the selected gear into the
next lower gear until it reaches 1st gear,
based on road speed and engine RPM. Auto­
matic downshifting is interrupted as soon as
you apply the throttle again.
(D Tips
- When you shift into the next lower gear,
the transmission will downshift only
when there is no possibility of over-rev­
ving the engine.
- When the kick-down comes on, the
transm ission w ill shift down to a lower
gear, depending on vehicle and engine
speeds .
- tiptronic is inoperative when the trans­
mission is in the fai l-safe mode.
Steer ing wheel with tiptronic
Applies to vehicles: with tiptronic steering wheel
The shi~ buttons on the steering wheel allow
the driver to shift gears manually.
Fig. 1 10 Steer ing w hee l: S hift bu ttons
• To downshift, touch the button on the left
0 -
• To upshift, touch the button on the right
0.
The shift buttons are activated when these­
lector lever is in
D/S or in the manual shift
program (tiptronic) .

until near maximum RPM is reached, or until
the driver shifts into 2nd gear.
I f yo u take your foot off the accelerator pedal
when dr iving down a steep incline, tiptronic
will downshift from the selected gear into the
next lower gear until it reaches 1st gear,
based on road speed and engine RPM. Auto ­
matic downshifting is interrupted as soon as
you apply the throttle again.
@ Tips
- When you shift into the next lower gear,
the transmission will downshift only
when there is no possibility of over-rev­
v ing the engine.
- When the kick-down comes on, the
transmission will shift down to a lower
gear, depending on vehicle and engine
speeds.
- tiptron ic is inoperative when the trans­
mission is in the fail-safe mode .
Steering wheel with tiptronic
Applies to vehicles: with tiptro nic steer ing wheel
The shift buttons on the steering wheel allow
the driver to shift gears manually.
Fig. 117 Steering wheel: Sh ift buttons
• To downshift, touch the button on the left
0-
• To upsh ift, touch the button on the right
0-
The shift buttons are activated when the se­
lector lever is in
D/S or in the manual shift
program (tiptronic).
Automatic Transmission 111
Of course, you can continue to use the manual
shift program with the selector lever on the
center console.
Transmission malfunction
Applies to vehicles : wit h tipt ro ni c
[O] Transmission : please press the brake ped ­
al and select the position again
Press the brake pedal and select the desired
selector lever position again. You can then
continue driving.
[O] Transmis sion hot: please modify driving
style
T he tran smission temperature has increased
s ig nificantly due to the sporty driving manner .
Dr ive in a less sporty manner until the tem ­
perature returns to the normal range and the
indicator light switches of.
[O] Transmission malfunction: You can con­
tinue driving
T here is a system malfunction in the transmis­
sion. You may cont inue driving. Drive to your
a uthor ized Audi dea le r or qualified repair fa­
cility soon to have the malfunction corrected.
[O] Transmission malfunction: Limited driv­
ing functionality
There is a system malfunction in the transmis­
s ion. The transmission is switching to emer­
gency mode. This mode on ly shifts into cer­
tain gears or will no longer shift at all. The en­
gine may sta ll. Drive to your authorized Audi
dealer or qualified repair facility immediately
to have the malfunction corrected .
[O] Transmission malfunction: Stop and shift
to P
Do not continue dr iving. Select the P selector
lever position and see your authorized Audi
dealer or qualified repair facility for assis­
tance.
(D Note
If the transmission switches to emergency
mode, you should take the vehicle to an
IJll>

Programming transmitters
Applies to vehicles: with Horne link
You con program the buttons in the Home­
Link universal remote control located in the
vehicle headliner.
F ig. 129 Contro l u ni t in th e headlin er
Fig. 130 Left front a rea of the b um per
Programming a button
M 0
9 C)
~
• Make sure your veh icle is within operating
range of the remote controlled garage door
opener.
• Set the parking brake¢
A in General infor­
mation on page 120.
• Switch the ignition on. Do not start the en­
gine!
• There are two ways to program a button :
press the button that you would like to pro ­
gram . The MMI will display instructions to
guide you through the programm ing . Or
• Select : IC ARI funct ion button >
Car systems
control button > Vehicle settings > Garage
door opener> Program garage door open­
er .
• Se lect the button that you would like to
program.
• Follow the instructions in the MMI.
• If the garage door opening must also be
synchronized w ith the Homelink module,
Homelink ® 121
refer to the owner's manua l for the garage
door opener .
Using the programmed button
• Press the programmed button¢ A in Gen­
eral information on page 120
to open the
garage door. The light @will blink or turn
on.
• Press the button again to close the garage
door ¢
A in General information on
page 120.
Erasing the button programming
• Select: !CAR !function button> Car systems
function key > Vehicle settings > Garage
door opener > Clear program settings
>
Yes.
Displaying the version/status/country
code
• Select: I CAR ! function button > Car systems
contro l button > Vehicle settings > Garage
door opener > Version information .
You can program both fixed code and rolling
code systems using these instructions.
Programming a button
The requ ired distance between the handheld
transmitter and the Homelink modu le in the
bumper depends on the system that you are
programming. You may have to try several
times.
Each of the buttons can be reprogrammed in­
dividually. The procedure is the same as for in­
itial programming .
¢page 121, Programming
a button.
Erasing the button programming
Individual buttons can be reprogrammed. Fol­
low the same steps used when first program­
ming the button.
If you would like to erase all programmed but­
tons at the same time, select Erase button
programming.

122 Homelink®
- To ensure your safety, erasing the pro­
grammed Homel ink buttons before sell­
i ng the vehicle is recommended.
- Depend ing on the model of the garage
door opener, you may need to release the
button on the remote and press it again
when programming.

210 Cleaning and protec tio n
-Always read and heed all WARNINGS and
other information
c> page 204.
Exhaust tail pipes
Road salt and other corrosive materials will
damage the material in the exhaust tail pipes
if they are not cleaned regularly . Do not clean
the tail p ipes with wheel cleaner, paint pol ish,
chrome po lish or other abrasive cleaners.
C lean the tail p ipes with car ca re p roducts
that are su itable for stain less stee l.
Your author ized Audi dealer can provide clean­
ing p roducts that have been tested and ap­
p roved fo r you r vehicle.
Care of interior
Infotainment components
The MMI/RSE* display may be cleaned with a
soft cloth and commercially-ava ilable "LCD
cleaner" . The cloth should be coated lightly
when the clean ing solution when cleaning the
d isplay.
The MMI/RSE* contro ls must be cleaned first
with a brush so t hat dirt does not ente r the
un it or enter between the buttons and the
housing. Then wiping the controls with a cloth
dampened with dish detergent and water is recommended.
CJ) Note
- To avoid sc ratch ing the disp lay, you
shou ld never clean it dry.
- To prevent damage, ma ke sure fluids do
not enter the controls.
Aluminum trim
Use only n eutral-pH products to remove spots
and deposits from aluminum surfaces.
Chrome ca re products and alkaline cleaners
will attack aluminum s urfaces and can dam­
age them over time.
A WARNING
A lways read and heed all WARNINGS and
other information
c> page 204.
Fabrics and fabric coverings
Fabr ics and fabric cover ings (e .g. seats, door
trim panels, etc.) should be cleaned at regular i ntervals w ith a vacuum cleaner. This removes
su rface di rt particles which could become em ­
bedded in the fabri c through use. Steam
cleaners should not be used, because the
steam tends to p ush the dirt deeper into the
fabric and lock it there.
Normal clean ing
Generally, we recommend using a soft sponge
o r a lint-free microfiber clo th to the clean fab­
ric. Brushes shou ld only be used for carpets
and floor mats, since other fabric surfaces
could be harmed by brushes.
Norma l su rface stains can be cleaned using a
commercially available foam cleaner . Spread
the foam on the s urface of the fabric with a
soft sponge and work it in gently. Do not satu­
rate the fabric. Then pat the foam dry using
absorbent, dry cloths (e.g. m icrof iber cloth)
and vacuum it after it has dried completely.
Cle anin g sta ins
Stains caused by beverages (e .g. coffee, fruit
juice, etc.) can be treated with a mild deter­
gent solution. Apply the detergent solution
with a sponge. In the case of stubborn stains, a detergent paste can be applied directly to
the stain and worked into the fabric. After­
wards, use copious amounts of clean water to
remove the rema in ing deterge nt. Apply the
water wit h a damp clo th or sponge an d pat
the fabric dry with an abso rbent, dry cloth .
Stains from choco late or makeup should have
detergent paste (e.g. ox-gall soap) rubbed in­
to them. Afterwa rds, remove the soap with
water (damp sponge) .
Alcohol can be used to treat stains from grease, o il, lipstick or a ballpoin t pen . Melted ..,.