2012 AUDI A3 brakes

176 Trailer towing
Always app ly bra kes early . When driving
downhill, shift into lower gear to use the en­
g ine braking effect to slow down the vehicle.
Use of the brakes alone can cause them to
overheat and fail.
Coolant temperature
The coolant temperature gauge ¢ page 11
must be observed carefully. If the needle
moves close to the upper end of the scale, re­
duce speed immed iate ly and/or switch
off the
a ir cond itioner.
If the coolant temperature warning light in
the instrument cluster starts flashing
J_, pull
off the road, stop and let the engine idle for
about two minutes to prevent heat build-up.
A WARNING
Anyone not properly restrained in a mov­
ing veh icle is at a much greater risk in an
accident . Never let anyone r ide in your car
who is not prope rly wear ing the restra ints
provided by Aud i.
Trailer towing tips
Important to know
Your veh icle handles different ly when towing
-
a trailer because of the addit io nal weight and
weight distribution . Safety, performance and
economy w ill greatly depend on how carefu lly
you load your trai ler and ope rate your rig .
Before you actually tow your trailer, practice
turn ing, stopp ing and back ing up in an area
away from traffic. Keep practicing until you have comp letely become fam iliar w ith the way
your ve hicle-trai ler comb ination behaves and
responds .
Backing up is d iff icu lt and requires practice .
Backing up with a tra ile r genera lly requ ires
steer ing act ion opposite of tha t when backing
up your veh icle without a trailer .
Ma intain a g reater distance between your ve­
h icle and the one in fro nt of you. You will need
mo re room to stop. To compensate for the trailer, yo
u will need a
larger than normal turning radius.
When passing, remember that you cannot ac ­
ce le rate as fas t as you no rma lly would be­
cause of the added load. Make sure yo u have
enough room to pass . After passing, a llow
plenty of room for your trailer before chang ­
ing lanes again.
Avoid jerky starts , sharp turns or rapid lane
changes.
(D Tips
- Do not tow a trailer during the break -in
period of your vehicle.
- If you tow a trailer, yo ur Audi may re­
quire more frequent maintenance due to
the extra load ¢
page 2 59.
Parking on a slope
Do not park with a trailer on a slope . If it can­
not be avoided, do so only after doing the fol­
lowing:
When parking:
.,. App ly the foot brake.
.. Have someone p lace cho cks under both the
veh icle and the trailer wheels.
.. With chocks in place, slowly release the
brakes unti l wheel b locks absorb th e load.
.. Turn the whee ls towards the cu rb.
.. App ly the parking brake.
.. Place an automat ic transm ission in
P, re­
spectively a manual transmission in first or
reverse gear .
When restarting after p ark ing:
.. Start the engine.
.. Shift transm ission into gear .
.. Release the parking brake and slowly pull
out and away from the wheel blocks.
.,. Stop and have someone retr ieve the wheel
b locks .
Ill-

178 Cleaning and protection
Cleaning and
protect ion
General information
Regular core preserves vehicle value .
Any automobile is exposed to industrial
fumes, corrosive road salt, etc. A well cared
for Audi can look like new many years after purchase . Regular and correct care w ill con­
tr ibute to maintaining the beauty and value of
your Aud i.
Furth erm ore, goo d car e m ay b e a cond iti on
for substantiat ing a warrant y claim shou ld
c orrosion dam age or paint d efe ct s occ ur.
Your author ized Audi dealer has a variety of
d ed ica ted vehicl e-ca re product s and can ad ­
vise which ones to use for cleaning the exter i­
or and inte rior of your vehicle .
Whether you use products recommended by
Aud i or other commercially ava ilable clean ing
agents, please make sure you apply them cor­
r ectly .
A WARNING
-Cleaning agents may be poisonous. Keep
them out of the reach of children.
- Heed a ll caut ion labels.
- Always read directions on the container
before using any product . Follow the di­
rect ions carefu lly.
- Most chemical cleaners are concentrated
and have to be diluted.
- Use spot removing fluids only in well
ventilated areas.
- Do not use gasoline, kerosene, d iesel
fuel, nail pol ish remover or other volati le
fluids. They may be toxic, flammab le or
haza rdous in other ways. Do not wash,
wax or dry the vehicle with the ignit ion
on or the engine running.
- Do not clean the undersides of chassis,
fenders, wheel covers, etc. without pro­
tecting your hands and arms. You may
c u t yourself on sharp-edged metal parts . -
Moisture and ice on brakes may impair
brak ing eff ic iency
c::> page 163 , General
information.
Test the brakes carefully
each time you wash the vehicle .
@ For the sake of the environment
Select only environ mentally friendly clean­
i ng products. Leftover cleaning products
should not d isposed of in the househo ld
waste .
Care of exterior
Washing
Frequent washing protects the vehicle .
The best protection against environmental in ­
fluences is
frequent washing and waxing .
How often this is required depends on:
- How much the vehicle is used
- Where the veh icle is parked (garage, in the
open under trees, etc.)
- The seasona l and weather conditions
- Environmental i nfl uences
The longer b ird droppings, insects, tree resin,
r oad and industrial gr ime, tar, soot, road salt
and other mater ials remain on the veh icle
body, the mo re lasting their destructive ef­
fects w ill be .
High temperatures , as from expos ure to in­
tense sun light, intensify the corrosive effect
part icularly when hum idity is high as well.
Under certa in circumstances,
we ekly washing
may be necessary. Unde r other cond itions, a
monthly washing and waxing may be ade­
quate.
After the winter, the unders ide of the vehicle
should be thoroughly washed, preferably in a professional car wash .
A WARNING
Always read and heed all WARNINGS and
other info rma tion
c::> page 178 .

182 Cleaning and protection
• Wipe the windows dry with a clean piece of
cloth or kitchen paper towel.
The best way to remove snow from w indows
and mir rors is to use a brush. Use a non -abra­
sive
pla stic ice scraper -better still, a spray
deicer -to remove
ic e from windows and mir­
rors.
The windows must not be cleaned with insect remover or wax since these can interfere with
the function of the windshield wiper blades (chatter).
O il, grease or silicone residue can be removed
with
glass cle aner or silicone remo ver. How­
ever, wax residue req uires the use of a specia l­
ly form ulated solvent. P lease contact your au­
thor ized Audi dealer for adv ice on safe prod­
ucts for wax removal.
Windows sho uld a lso be cleaned on the inside
at regular interva ls.
Never dry windows with the same chamois
that you use to dry painted s urfaces. Wax resi­
due on the chamois can impair vision thro ugh
the windows.
A WARNING
- The windshie ld m ust not be treated with
water-repellent materials. They can i n­
c rease glare under poor visib ility condi­
t ions such as wetness, darkness, o r whe n
the sun is low on the hori zon. In addi­
t io n, they ca n cause the wi ndshield wip ­
ers to chatter .
- Always read and heed all WARN INGS and
othe r inform ation
Qpage 178.
0 Note
- Never use warm or hot water to remove
s now and ice from windows a nd mirrors.
This cou ld cause the g lass to c ra ck .
- To prevent damage to the wi res of the
r ear defogger, do not place any adhesive
sticke rs o n the inside of t he rear w indow
ove r the wires.
- To he lp prevent d irt from s cratch ing the
window, always scrape i n a forwar d di- rec
tion -pushing the sc raper away from
you -never bac k and fort h.
Steel wheels
Applies to vehicles: with steel wheels (e .g. if refitted with
winter tires)
The wheels also have to be cleaned.
• Always include the hub caps and wheel rims
when wash ing your vehicle to remove road
dirt, sa lt sprays and brake dust .
If necessary, use a commercial whee l cleaner
to remove accumulated brake dust.
The wheel rims are easier to keep clean i f they
are regularly coated with liq uid wax.
Paint scra tches shou ld be touched up as soon
as possib le to prevent corrosion
¢ page 181,
Touch-up paint.
A WARNING .....__
- Moisture and ice on brakes may affect
brak ing eff ic iency-
q page 163, General
information . Test the brakes ca refully af­
ter each vehicle wash .
- Always read a nd heed a ll WARNINGS and
the information
q page 178.
Cast (light) alloy wheels
Applies to vehicles : with Cast alloy wheels
-
Cast (light) alloy wheels require special care.
• Wash the w heels with a sponge or hose
brush every other week .
• For deep cleaning afterwards, use on ly a
ded icated acid-free cast alloy wheel cleaner.
• Rub a coat of
liquid wa x onto the rims every
three month. Be sure to reach and treat all
parts of the rim .
To preserve the decorative appearance of the cast alloy w heels, some special care is neces ­
sary. In addition to road dirt and salt, brake dust is also co rrosive . If left on fo r too long,
brake d ust can cause pitting.
U se only spec ial
acid -free cleaners formulated
fo r alloy r ims . Safe products are ava ilab le at ..,_

your authorized Audi dealer. Never leave the cleaner on the rims longer than specified on
the label. If not rinsed
off promptly, the acid
contained in some cleaners can attack the
threads on the wheel bolts.
Never use abrasive or meta l polishing clean­
ing agents.
If the protective coat ing has been
chipped, e.g. by kicked up road dirt, touch it
up as soon as possible.
A WARNING
-Moisture and ice on brakes may affect
braking efficiency~
page 163, General
information.
Test the brakes carefully
each time you wash the vehicle.
- Always read and heed all WARNINGS and
other information¢
page 178.
Body cavity sealing
-
The body cavity sealing does not need to be
checked.
All body cavities which could be affected by
corrosion have been thoroughly protected at
the factory.
This sea ling does not require any inspection or
addit ional treatment. If any wax should seep
out of the cavity when the ambient tempera­
ture is high, it can be removed with a plast ic
scrape r and a suitab le solvent .
A WARNING
Solvents can be dangerous.
- Benzine is flammable and toxic. If you
use benzine for removing the wax, keep
spar ks, flame and lighted cigarettes
aw ay. Never dump benzine on the
ground, in to open streams or down sew ­
age drains.
- B e sure to observe all safety and env iro n­
menta l regulations . Follow all instruc ­
tions on t he container .
- Always read and heed all WARN INGS and
other informa tion¢
page 178 .
Cleaning and protec tion 183
Chassis
Hove the undercoating checked for damage
from time to time.
The lower body shell of your Aud i is also thor­
oughly protected against corrosio n.
Any damage to the undercoating ca used by
road hazards should be repaired prompt ly.
A WARNING
Too much undercoating in the wrong p la­
ces can cause a fire.
- Do not apply additional undercoating or
rustproof ing on or near the exhaust
manifold, exhaust pipes, catalytic con­
verter or heat shields. While driving, the
substance used fo r undercoating could
overhea t and cause a fire.
- Always read and heed all WARNINGS and
other info rmation
¢ page 178.
Exhaust tail pipes
Road salt and o ther co rrosive materials w ill
damage the material in the exhaus t tail pipes
i f they are not cleaned regular ly . Do not clean
the tail pipes with whee l cleaner, pa int polish,
c h rome polish or other abrasive clea ners .
Clean the tail pipes with car care products
that are suitable for stainless steel.
Your authorized Audi dea ler can provide clean­
ing products that have been tested and ap­
proved for your vehicle.
Care of interior
Aluminum trim
Use only neutral-pH products to remove spots
and deposits from a luminum sur faces.
Chrome care products and a lkaline cleaners
will attack a luminum surfaces and can dam­
age them over time.
A WARNING
-Always read and heed all WARNINGS and
other information
¢ page 178.
•
•

206 Checking and filling
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a
quick glance .
Fig. 163 Engine compartme nt: brake flu id reservo ir
Before you check anything i n the engine com ­
partment,
a lwa ys rea d and h eed a ll WA RN·
ING S c:> & in Working in the engine compart ­
ment on page
194.
~ Read the brake fluid level from the bra ke
fluid reservoir. The brake fluid Level must be
between the "MIN" and "MAX" markings
9fig. 163 .
The brake f lu id rese rvoir is located at the rear
partition of the engine compartment on the
L eft side
¢page 196.
The fluid level may drop slightly after some
time due to the automatic adjustment of the b rake pads . This is not cause for alarm .
I f the b rake fluid Level falls
considerably be­
low the "MIN" mark, the brake wa rning/ind i­
cator Light (U.S. models:
1111 , Canadian
models:
llllt will come on c:> page 15 . Do not
continue to operate the vehicle . The complete
brake system sho uld be thoroughly checked
by an authorized Audi dealer or other quali­
fied facility and the cause corrected. If the
brake fluid level is too low, the brake warn ing/
indicator Light w ill illuminate . Contact an au­
thor ized Audi dealer
imm ediatel y.
Changing brake fluid
Have the brake fluid changed by an experi­
enced technician .
Brake fluid absorbs moisture from the air. If
the water content in the brake fluid is too high, corrosion in the brake system may result
after a period of time . The boiling point of the
brake flu id will also decrease conside rably and
decrease braking pe rformance.
Therefore, the brake fluid must be changed
eve ry two y ears. Always use new brake flu id
which conforms to Federal Motor Veh icle
Standard "F MVSS 116 DOT 4".
The brake fluid reservoir can be diff icult to
reach, therefore, we recommend that you
have the b rake fluid changed by your author­
ized
Audi dealer . Your dealer has the correct
tools, the right brake fl uid and the know -how
to do this for you.
A WARNING
- Brake fluid is poisonous . It must be stor­
ed only in the closed original container
out of the reach of children!
- Brake failure can resu lt from o ld or inap­
propriate brake flu id. Observe these pre­
cautions:
- Use only brake f luid that meets SA E
specifica tion
J 1 7 03 and conforms to
Federa l Moto r Ve hicl e Standard 1 16.
Always check with yo ur authorized Aud i
dealer to make sure yo u are using the
correct brake fluid. The correct type of brake f lu id is also ind icated on the
brake flu id reservoir.
- The brake fluid must be new. Heavy use
of the brakes can cause a vapor lock if
the brake fluid is left in the system too
l ong. This can seriously affect the effi­
c iency of the brakes as well as your
safety. This cou ld resu lt in an accident.
(D Note
Brake fluid will damage the paint of your
vehicle .

214 Tires and wheels
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options weight
Maximum (permissible) inflation pressure
means the maximum cold inflation pressu re
to which a tire may be inflated. Also called
"maximum inflation p ressure."
Normal occupant weight
means 150 lbs. (68 kilograms) times the
number of occupants seated in the vehicle up
to the total seating capacity of your vehicle.
Occupant distribution means distribution of occupants in a vehicle .
Outer diameter means the overa ll diameter of an inf lated new
tire.
Overall width
means the linear distance between the exteri­
ors of the sidewalls of an inflated tire, includ­
ing e levations due to labeling, decorations, or
protective bands or ribs.
Ply
means a layer of rubber-coated parallel cords.
Production options weight
means the comb ined weight of those installed
regular production options weighing over 5
lbs . (2 .3 kg) in excess of those standard items
which they replace, not previously considered
in curb weight or accessory weight, including
heavy duty brakes, r ide leve lers, roof rack,
heavy duty battery, and specia l trim .
Radial ply tire
means a pneumatic tir e in which the p ly cords
that extend to the beads are laid at substan­
tially 90 degrees to the centerline of the
tread . Recommended inflation pressure
see
~
page 213, Cold tire inflation pressure.
Reinforced tire
means a t ire designed to operate at higher
loads and at higher inflation pressures than
the corresponding standard tire . Re inforced
t ir es my be identified as "XL", "xl", "EX TRA
LOAD", or "RF" on the sidewall.
Rim
means a metal support for a tire or a t ire and
tube assembly upon which the tire beads are seated.
Rim diameter
means nom inal d iameter of the bead seat. If
you change your wheel s ize, you w ill have to
purchase new tires to match the new r im di­
ameter .
Rim size designation
means rim diameter and width.
Rim width
means nominal distance between rim flanges .
Sidewall
means that portion of a tire between the
t read and bead.
Speed rating (letter code)
means the speed at which a tire is designed to
be driven for extended periods of time. The
ratings range from 93 mph (150 km/h) to
186 mph (298 km/h)
~ page 224 . You may
not find this information on all tires because
it is not requ ired by law.
The speed rating letter code, where applica­
ble, is molded on the tire sidewall and indi­
cates the max imum pe rmissibl e road speeds
~ A in Winter tires on page 228.
Tire pressure monitoring system*
means a system that detects when one or
more of a veh icle's tires are underinflated and
illuminates a low tire pressure warning tell­
tale.

218 Tires and wheels
This is especia lly important if the vehicle be­
longs to someone else or you bought the vehi­
cle with different rims/tires or you bought the
vehicle as a previously owned vehicle.
Remember, your safety and that of your pas­
sengers also depends on making sure that
load limits are not exceeded. Vehicle load in­
cludes everybody and everything in and on the
vehicle. These load limits are technically refer­
red to as the vehicle's Gross Vehicle Weight
Rating (' 'GVWR"). The Gross Axle Weight Rat­
ing ("GAWR") is the maximum load that can
be applied at each of the vehicle's two axles.
The Gross Vehicle Weight Rating and the
Gross Axle Weight Rating are listed on the
safety compliance sticker label located either
on the driver's side B-pillar or on the inside of
the fuel filler flap. The tire pressure label on
your Audi lists the maximum combined
weight of all of the occupants and luggage or
other cargo that the vehicle can carry. For the
location of the tire pressure label
o fig. 167.
_& WARNING
Overloading a vehicle can cause loss of ve­
hicle control, a crash or other accident, se­
rious personal injury, and even death.
- Carrying more weight than your vehicle
was designed to carry will prevent the
vehicle from handling properly and in­
crease the risk of a loss of vehicle con­
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
vehicle within a safe distance.
- Tires on a vehicle that has been overload­
ed can fail suddenly causing loss of con­
trol and a crash.
- Always make sure that the total load be­
ing transported -including the weight of
a trailer hitch and the tongue weight of a
loaded trailer -does not make the vehi­
cle heavier than the vehicle's Gross Vehi­
cle Weight Rating.
A WARNING
- Incorrect tire pressures and/or underin­
flation can lead to a serious or fatal acci­
dent.
- Incorrect tire pressures and/or underin­
flation cause increased tire wear and can affect the handling of the vehicle.
- Incorrect tire pressures and/or underin­
flation can also lead to sudden tire fail­
ure, including a blowout and sudden de­
flation, causing loss of vehicle control.
Checking tire pressure
The correct tire pressure for the tires original­
ly installed on your vehicle is listed on the tire
pressure label located either on driver's side 8-pillar or inside the fuel filler flap.
The recommended tire pressures are on the
tire pressure label and in the table
o page 216, Cold tire inflation pressure. This
means that the pressure must be checked and
adjusted when the tire has not been driven for
more than a couple of miles (kilometers) at
low speeds during the previous three hours.
Air in the tires expands when the tire heats up
as a result of internal friction as it flexes in
use. The tire pressure is highe r when the tire
has warmed up than when it is "cold ."
It is the inflation pressure in a "cold" tire that
counts. Therefore, you should never let air out
of a warm tire to match "Cold tire inflation
pressure" recommendations
o page 216. The
tires would then be underinflated and could
fail suddenly.
The tire pressure label on your Audi lists the
recommended cold tire inflation pressures for
the new, original equipment tires that were
on your vehicle at the time it was manufac­
tured. For the location of the label
opage 216, fig. 167.
Most tires lose air naturally over time . They
can also lose some air if you drive over a pot­
hole or hit a curb while parking. It is usually
not possible to see whether the radial tires ..,.

The tire pressure label on your Audi also lists
the maximum combined weight of all of the
occupants and luggage or other cargo that
the vehicle can carry. For the location of the
label
c:::>page 216, fig. 167.
A WARNING
Overloading a vehicle can cause loss of ve­
hicle control, a crash or other accident, se­
rious personal injury, and even death.
- Carrying more weight than your vehicle was designed to carry will prevent the
vehicle from handling properly and in­crease the risk of the loss of vehicle con­
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
vehicle within a safe distance.
- Tires on a vehicle that has been overload­
ed can fail suddenly, including a blowout
and sudden deflation, causing loss of
control and a crash.
- Always make sure that the total load be­
ing transported -including the weight of
a trailer hitch and the tongue weight of a
loaded trailer -does not make the vehi­
cle heavier than the vehicle's Gross Vehi­
cle Weight Rating.
Determining correct load limit
Use the example below to cal­
culate the total weight of the
passengers and luggage or oth­
er things that you plan to trans­
port so that you can make sure
that your vehicle will not be
overloaded.
Steps for Determining
Correct Load Limit
1. Locate the statement "THE
COMBINED WEIGHT OF QC-
Tires and wheels 221
CUPANTS AND CARGO
SHOULD NEVER EXCEED XXX
KG OR XXX LBS"on your vehi­
cle's placard (tire inflation
pressure label)
¢ page 216,
fig. 167.
2. Determine the combined
weight of the driver and pas­
sengers that will be riding in
your vehicle.
3. Subtract the combined
weight of the driver and pas­
sengers from
"XXX" kilo­
grams or
"XXX" pounds
shown on the sticker
¢ page 216, fig. 167.
4. The resulting figure equals
the available amount of car­
go and luggage load capaci­
ty. For example, if the
"XXX"
amount equals 1400 lbs.
and there will be five 150
lbs. passengers in your vehi­
cle, the amount of available
cargo and luggage load ca­
pacity is 650 lbs. (1400-7 50
(5
X 150) = 650 lbs.)
5. Determine the combined
weight of luggage and cargo
being loaded on the vehicle.
That weight may not safely
exceed the available cargo
•
•