2012 Alfa Romeo Giulietta wheel

76
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
EXTERIOR COURTESY LIGHTS
This function lights up the vehicle and the space around it when
the doors are unlocked.
Activation
When the car is parked and the doors are unlocked by pressing the
Ëbutton on the remote control (or the boot is unlocked by press-
ing
R), the dipped beam headlights, side lights and number
plate lights are activated.
The lights remain lit for approximately 25 seconds unless the doors
and boot are locked once again, the doors or boot are opened
and closed or the instrument panel is activated. In these cases they
go out after 5 seconds.
The exterior courtesy lights can be enabled/disabled using the Set-
up Menu (see the paragraph “Menu Items” in this chapter).
“FOLLOW ME HOME” DEVICE
This device allows you to illuminate the area in front of the car
for a certain amount of time.
Activation
With the ignition key on STOP or removed, pull A stalk fig. 40 to-
wards the steering wheel within 2 minutes of the engine switch-
ing off.
Each time the stalk is moved, the lights stay on for an extra 30
seconds up to a maximum of 210 seconds; then the lights are
switched off automatically.
The
3warning light on the instrument panel will light up (and
the corresponding message will appear on the display) as long as
the function is active.
The light comes on when the stalk is first moved and stays on un-
til the function is automatically deactivated. Each movement of the
stalk increases only the amount of time the lights stay on.
Deactivation
Keep the A stalk fig. 40 pulled towards the steering wheel for more
than 2 seconds.

77
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Move the stalk up (unstable position) to limit operation to the time
for which the stalk is held in this position. When released, the stalk
will return to its default position and the wiper will be automati-
cally stopped.WINDOW CLEANING
The right stalk controls windscreen wiper/washer and heated rear
windscreen wiper/washer operation.
WINDSCREEN WIPER/WASHER fig. 41
This only operates with the ignition turned to MAR. The ring nut A
can have the following positions::
Owindscreen wiper off;
≤intermittent operation (low speed);
AUTO rain sensor activation (for versions/markets, where pro-
vided) (the windscreen wiper speed is automatically adapt-
ed to the intensity of the rain)
nintermittent operation;
≥slow operation;
¥fast operation.
fig. 41A0K0097m
Do not use the windscreen wipers to remove lay-
ers of snow or ice from the windscreen. In such con-
ditions, the windscreen wipers may be subjected to
excessive stress, prompting intervention from the motor
protection which prevents operation for a few seconds. If
operation is not restored, even after turning the key and
restarting the engine, contact Alfa Romeo Authorized Ser-
vices.
Do not operate the windscreen wiper with the
blades lifted from the windscreen.
“Smart washing” function
Pull the stalk towards the steering wheel (unstable position) to op-
erate the windscreen washer jet. Keep the stalk pulled for more
than half a second, with just one movement, to operate windscreen
washer/wiper jet at the same time.
The wiper stops working three strokes after the stalk is released.
A further stroke after approximately six seconds completes the wip-
ing cycle.

88
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
On some versions the compartments may be heated/cooled by an
air vent connected to the climate control system (operate wheel
A-fig. 55a to adjust the air flow rate to the lower compartment).
In versions with dual-zone automatic climate control system, the glove
compartment is set to the same temperature as the passenger's side.
In versions with dual zone automatic climate control system, a bot-
tle/can holder is present inside the compartment on passenger
side.
One 50 cl bottle and two slim cans can be fitted inside at the same
time. The handbook may be inserted under the bottle holder with
the longer side facing towards the front of the car.
fig. 55aA0K0185m
Do not travel with the compartments open: the
front seat occupants could be injured in case of
an accident.
FRONT ARM REST
(for versions/markets, where provided)
This is located between the front seats. To bring this to the stan-
dard position of use, push it down as shown in the figure.
There is a compartment inside the arm rest: lift the A cover
fig. 56 to access the compartment.
fig. 56A0K0166m

109
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTSIf the ABS intervenes, it means you have almost
reached the limit of grip between the tyres and the
road surface: slow down to make sure you can use
the available grip.
ABS SYSTEM
ABS is an integral part of the braking system, which prevents the
wheels from locking when braking, makes the most of road grip
and gives the best control when performing emergency braking un-
der difficult road conditions.
The EBD system (Electronic Braking Force Distribution) completes
the system, allowing the brake force to be distributed between the
front and rear wheels.
IMPORTANT For maximum efficiency of the braking system, a bed-
ding-in period of about 500 km is needed: during this period it is
better to avoid sharp, repeated and prolonged braking.
The ABS gets the most out of the available grip,
but it cannot increase it; you must therefore always
take care when driving on skiddy roads. Do not
take any unnecessary risks.
When the ABS intervenes and you notice the brake
pedal pulsating, do not be afraid to keep the ped-
al pushed down. This will help you to stop in the
shortest distance possible, depending on the road condi-
tions.
SYSTEM INTERVENTION
The brake pedal pulsates slightly and the system gets noisier: it
means that the speed should be altered to suit the type of road sur-
face.

110
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
VDC SYSTEM
(Vehicle Dynamics Control)
This is an electronic system that controls vehicle stability in the
event of tyre grip loss, helping maintain directional control. The sys-
tem is capable of recognising potentially dangerous situations in
terms of the stability and intervenes automatically on the brakes
in a differentiated manner for the four wheels in order to provide
a stabilizing torque.
The VDC, in turn, includes the following systems:
❍Hill Holder
❍ASR
❍Brake Assist
❍MSR
❍CBC
❍“ELECTRONIC Q2” (“E-Q2”)
❍DST
❍RAB
SYSTEM INTERVENTION
This is signalled by warning light áblinking on the instrument
panel to inform the driver that stability and grip conditions are
critical.
SYSTEM ACTIVATION
The VDC system switches on automatically each time the engine
is started and cannot be switched off.
HILL HOLDER SYSTEM
This system is an integral part of the VDC system and it is provided
to facilitate starting on slopes.
It is activated automatically in the following instances:
❍uphill: car standing on a road with a gradient of more than 5%,
engine on, brake pedals pressed and gearbox in neutral or gear
(other than reverse) engaged;
❍downhill: car at a standstill on a road with a gradient higher
than 5%, engine running, brake pedal pressed and reverse gear
engaged.
When setting off the VDC system control unit maintains the brak-
ing pressure at the wheels until the engine torque required for de-
parture is reached or for approximately 2 seconds, allowing your
right foot to be moved easily from the brake pedal to the acceler-
ator.
If the car does not start off after this time, the system will deacti-
vate automatically by gradually releasing the brake force. A noise
may be heard: this means that the car is about to start moving.
IMPORTANT the Hill Holder system should not be used as a hand-
brake. Do not leave the vehicle without having engaged the hand-
brake, switched off the engine and engaged a gear.

111
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
ASR SYSTEM (AntiSlip Regulation)
It is an integral part of the VDC system. It intervenes automatical-
ly if one or both of the drive wheels is slipping, there is a loss in
grip on a wet surface (aquaplaning), acceleration on slippery, snow-
covered or icy surfaces, etc.
Depending on how slippery the road is, two different control sys-
tems are activated:
❍if the slipping involves both drive wheels, the ASR intervenes
reducing the power transmitted by the engine;
❍if the slipping only involves one of the drive wheels, the ASR
intervenes automatically braking the wheel that is slipping.
In order for the ESP and ASR systems to operate
correctly, it is essential that the tyres are of the
same brand and type on all wheels, in perfect con-
dition and, above all, of the specified type, brand and size.
If the space saver wheel is used, the VDC system
keeps operating. Be aware however that the space
saver wheel, being smaller than the original wheel,
provides less grip.
The performance of the VDC and ASR systems
should not encourage the driver to take unneces-
sary risks. Your driving style should always take
road conditions, visibility and traffic into account. The dri-
ver is always ultimately responsible for road safety.

112
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
“ELECTRONIC Q2” SYSTEM (“E-Q2”)
The “Electronic Q2” system uses the braking system to create an
effect similar to a limited slip differential.
The front braking circuit, when accelerating around a corner, acts
on the inside wheel to increase the drive to the outside wheel (in-
creased load), dynamically and continuously distributing the torque
between the front drive wheels according to driving and road con-
ditions.
The system, combined with Mc Pherson front suspension, allows
particularly effective, sporty driving.
DST SYSTEM (Dynamic Steering Torque)
This function integrates Dual Pinion active steering into the opera-
tion of VDC. For particular manoeuvres, VDC controls the steering
to actuate a steering torque and assist the driver in the best pos-
sible way. The system operates the brakes and steering in a coor-
dinated manner to increase the suspension and safety level of the
car as a whole. The steering provides addition torque on the steer-
ing wheel.
RAB SYSTEM (Ready Alert Brake)
(“Dynamic” mode only)
By pre-approaching the brake pads (front and rear) after rapid ac-
celerator release, this function provides prompter braking and re-
duces stopping distance.
BRAKE ASSIST
(emergency braking assistance)
The system, which cannot be turned off, recognises emergency
braking (on the basis of the brake pedal operating speed) and
speeding up the response of the braking system. The Brake
Assist function is deactivated in the event of VDC system fault.
MSR SYSTEM
(Motor Schleppmoment Regelung)
This system is an integral part of the ABS, that intervenes, if there
is a sudden change to a lower gear, restoring torque to the engine,
thereby preventing excessive drive at the drive wheels which, es-
pecially in poor grip conditions, could lead to a loss in stability.
CBC SYSTEM (Cornering Braking Control)
This system improves the distribution of the braking pressure at the
four wheels (to fully exploit the grip available on the ground) when
braking round bends when the ABS intervenes. This improves stop-
ping distances and above all vehicle stability when cornering.

113
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
“Alfa DNA” SYSTEM
(Dynamic control system)
This device allows, using switch A-fig. 80 (on the central tunnel),
three response modes to be selected according to driving style
and road conditions:
❍d = Dynamic (for sporty driving)
❍n = Normal (normal driving mode)
❍a = All Weather (driving mode for poor grip conditions, i.e. rain
and snow on the road)
The device also acts on the dynamic vehicle control systems (en-
gine, steering, VDC system, instrument panel).
When the lever A-fig. 80 is moved to “d” position, the activation
of “Dynamic” mode is confirmed by a temporary variation in the
brightness (flashing) of the instrument panel.
fig. 80A0K0072m
DRIVING MODES
Switch A-fig. 80 is a monostable switch, i.e. it always remains in the
central position. The selected driving mode is indicated by the corre-
sponding LED coming on in the panel and by an indication on the re-
configurable multifunction display, as illustrated below:
A0K0009m
A0K0010m
Dynamic mode (display image available for
versions/markets where
provided)All Weather mode
“Normal” mode
When “Normal” mode is selected, no messages or symbols are
shown on the display.
VDCandASR: operating thresholds set for normal comfort lev-
el for normal driving conditions.
Steering tuning: functions aimed at providing comfort in nor-
mal conditions of use.
DST: Standard braking control coordinated with ABS/VDC.
Standard control over lateral acceleration.
Oversteer compensation: a slight pulse on the steering wheel
encourages the driver to carry out the most appropriate ma-
noeuvre.
Engine: Standard responsiveness