2012 Alfa Romeo Giulietta battery

86
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
AFS ADAPTIVE LIGHTS
(Adaptive Frontlight System) fig. 52
(for versions/markets, where provided)
This is a system combined with xenon headlamps which directs the
main light beam and continuously and automatically adapts it to
the driving conditions round bends/when cornering. The system
directs the light beam to light up the road in the best way, taking
into account the speed of the vehicle, the bend/corner angle and
the speed of steering.
The adaptive lights are automatically activated when the engine
is started. In this condition, LED A-fig. 52 will stay off. When the
button is pressed the adaptive lights (if on) are deactivated and the
LED A-fig. 52 in the button comes on continuously.
Press button again to turn the adaptive lights on (LED off).
fig. 52A0K0123m
DOOR LOCK fig. 53
Press≈to lock all the doors at the same time (the LED on the
button will light up when the doors are locked. Locking takes place
regardless of the position of the ignition key.
FUEL CUT-OFF SYSTEM
This system is tripped after a collision and activates the following
functions:
❍cutting off fuel supply and consequently stopping the engine;
❍automatically unlocking the doors;
❍turning on the inside lights.
The intervention of the system is indicated by a message shown
on the display. Carefully check the car for fuel leaks, for instance
in the engine compartment, below the car or near the tank area.
After a crash, turn the ignition key to STOP to avoid draining the
battery.
fig. 53A0K0145m

94
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
MAINTENANCE/EMERGENCY
In case of emergency or maintenance the roof can be moved man-
ually when there is no power supply (opening/closing of the front
glass panel) by carrying out the following operations:
❍remove cap A-fig. 65 set between the two sun curtains;
❍take the Allen key B supplied, which is located in the on-board
documentation container or in the tool container in the luggage
compartment;
❍introduce the key into housing C and turn it:
– clockwise to open the roof;
– anti-clockwise, to close the roof.
fig. 65A0K0132m
INITIALISATION PROCEDURE
The sunroof must be re-initialised after disconnecting the battery
or if the relevant protection fuse is blown.
Proceed as follows:
❍press button B-fig. 63 until the roof is entirely closed. Then
release the button;
❍press B button and keep it pressed for at least 10 seconds
and/or until the glass panel clicks forwards. Release the but-
ton at this point;
❍press button B within 5 seconds of this operation and keep it
pressed: the glass panel will complete a full opening and clos-
ing cycle. Only release the button at the end of this cycle.

95
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
DOORS
CENTRAL DOOR LOCKING/UNLOCKING
FUNCTION
Locking the doors from the outside
With the doors closed press button Áon the remote control or turn
the metal insert (located inside the key) in the driver’s door lock.
The LED over the button
≈will light up to indicate that the
doors have been locked.
The door locking function is operated:
❍with all the doors closed;
❍with all the doors closed and boot open.
fig. 66A0K0145m
Unlocking the doors from the outside
Press button Ëon the remote control or turn the metal insert (lo-
cated inside the key) in the driver’s door lock.
Locking/unlocking the doors from the inside
Press≈. The button has an LED that indicates the state (locked
or unlocked) of the doors.
LED on: doors locked. Press the button
≈again to unlock all
doors and switch the LED off:
LED off: doors unlocked. Press the button
≈again to lock
all doors. The doors will be locked only if all the doors are prop-
erly shut.
Once the doors have been locked via the remote control or the key
pawl, it will no longer be possible to unlock them by pressing but-
ton
≈.
IMPORTANT With the central locking function on, pull the inside
lever on the passenger’s door to unlock the door (the LED will stay
on). All doors will be unlocked if the inside lever on the driver’s
door is pulled.
IMPORTANT The rear doors cannot be opened from the inside when
the child lock is engaged.
If a power supply is not present (blown fuse, battery disconnect-
ed, etc.) it is, however, possible to lock the doors manually.

97
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
DOOR LOCK EMERGENCY DEVICE
Front passenger door
The front passenger door has a device to lock it when there is no
current. To lock it, fit the metal insert of the ignition key in the seat
A-fig. 67a and move it upwards.
Rear passenger door
The rear doors are fitted with an emergency device that allows
the doors to be locked when there is no current.
Proceed as follows:
❍insert the metal insert on the ignition key in the seat B-fig. 67;
❍turn the key anticlockwise and then remove it from the seat B.The door lock knob can be realigned (only when the battery charge
has been restored) as follows:
❍press button Ëon the key;
❍press≈on the instrument panel to lock/unlock the doors;
❍open the front door by inserting the key in the pawl;
❍pull the internal door handle.
If the child lock was engaged and the previously
described locking procedure carried out, operating
the internal handle will not open the door but will
only realign the door lock knobs. To open the door, the
outside handle must be used. The door central lock-
ing/unlocking button is not disabled by the engagement
of the emergency lock
≈.
IMPORTANT If the battery is disconnected or the protection fuse
blows, the luggage compartment opening/closing mechanism must
be reinitialised as follows:
❍shut all the doors;
❍press button Áon the key or door locking/unlocking button
≈on the instrument panel;
❍press button Ëon the key or door locking/unlocking button
≈on the instrument panel.
fig. 67aA0K0275m

100
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Electric window system initialisation
The system must be re-initialised after disconnecting the battery
or if the relevant protection fuse is blown.
Initialisation procedure:
❍fully close the window manually to initialise;
❍after the window has reached the upper end of travel, hold the
up button pressed for at least one second.
IMPORTANT For versions/markets where provided, following the
disconnection of the power supply (replacing or disconnecting the
battery or replacing the protection fuse for the electric window con-
trol units), the automatic setting for the electric windows must be
reset.The reset operation should be carried out with the doors closed
according to the following procedure:
1. completely lower the driver-side window and keep the button
pressed for at least 3 seconds once the end of travel position
has been reached (lower end stop);
2. completely raise the driver-side window and keep the button
pressed for at least 3 seconds once the end of travel position
has been reached (upper end stop);
3. repeat stages 1 and 2 also for the passenger’s window
4. check that the initialisation has taken place correctly by check-
ing the automatic operation of the windows.

102
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
BOOT INITIALISATION
IMPORTANT If the battery is disconnected or the protection fuse
blows, the boot opening/closing mechanism must be reinitialised
as follows:
❍close all the doors and the boot;
❍press button Áon the remote control;
❍press button Ëon the remote control.
CLOSING
To close, lower the tailgate and press down near the lock until
you hear it click. Handles A-fig. 71 are provided on the inside of
the tailgate to help grasping to close the tailgate.
IMPORTANT Before closing the boot make sure that you have the
keys with you because the boot will be locked automatically.
fig. 71A0K0181m

117
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
TURNING THE SYSTEM ON/OFF MANUALLY
PressTfig. 82 on the dashboard to turn the system on and off
manually.
Turning the Start&Stop system on
A message will appear on the display when the Start&Stop system
is on. In this condition, LED A-fig. 82 located over button
Tis off.
Turning the Start&Stop on
❍Versions with multifunction display: a message will appear on
the display when the Start&Stop system is off.
❍Versions with reconfigurable multifunction display: symbol T
and a message will appear on the display when the Start&Stop
system is off.
LED A-fig. 82 is on when the system is off.
fig. 82A0K0121m
FAILED ENGINE CUT-OUT CONDITIONS
When the system is operating, due to comfort, emission control
and safety reasons, the engine does not stop in some conditions,
among which:
❍engine still cold;
❍very cold outside temperature;
❍battery not sufficiently charged;
❍heated rear windscreen on;
❍windscreen wipers working at maximum speed;
❍particulate filter regeneration in progress (diesel engines only);
❍driver’s door not shut;
❍driver’s seat belt not fastened
❍reverse gear engaged (for example, for parking manoeuvres);
❍for versions equipped with dual zone automatic climate control
system (for versions/markets, where provided), if an adequate
level of thermal comfort has not been reached or MAX-DEF func-
tion activation;
❍during the first period of use, to initialize the system;
In these cases, a message is shown on the display and the sym-
bol
Uwill blink (the latter for versions/markets, where provid-
ed).
If climate comfort is to be favoured, the
Start&Stop system can be disabled, for a contin-
uous operation of the climate control system.

118
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Notes
If the clutch is not pressed, after 3 minutes from the engine stop-
ping, the engine can be restarted only using the ignition key.
In cases when the engine stops and this is not desired, due for
example to the clutch pedal being released sharply with a gear
engaged, if the Start&Stop system is activated, the engine can
be restarted by fully depressing the clutch pedal or by placing the
gear lever in neutral
RESTARTING CONDITIONS
For reasons of comfort, limiting harmful emissions and safety pur-
poses, the power unit can restart automatically without any action
on behalf of the driver if certain conditions are met, including:
❍battery not sufficiently charged;
❍windscreen wipers working at maximum speed;
❍low braking system vacuum, e.g. following the brake pedal be-
ing pressed repeatedly;
❍car in motion, for example when driving on hilly roads;
❍stopping the engine using Start&Stop longer than approxi-
mately 3 minutes;
❍for versions equipped with dual zone automatic climate control
system (for versions/markets, where provided), if an adequate
level of thermal comfort has not been reached or MAX-DEF func-
tion activation;
With gear engaged, the automatic engine restarting is possible on-
ly by fully pressing the clutch pedal. This operation is indicated to
the driver by means of a message on the display and by symbol
Ublinking (the latter for versions/markets, where provided).