2012 Acura TL stop start

Î
If you see a ‘‘CHECK DRL
SYSTEM’’ message on the multi-
inf ormation display, there is a
problem with the daytime running
light system. Take your vehicle to a
dealer to have it checked.
The headlights revert to normal
operation when you turn them on
with the switch. With the headlight switch of f or in
the position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights on
reminder beeper.
Headlights
Daytime Running L ights
142
11/01/14 18:18:07 31TK4630_147
Î
Models equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode
is the equivalent of ON (II). For more
information, see
page s 184 and 187.
:
Inst rument s and Cont rols
2012 TL

´
µ
´ µ
Î
Turn the f og lights on and of f by
turning the switch next to the
headlight switch.
You can use the f og lights only when
the headlights are on low beam.
With the light switch in the AUTO
position, you can also use the f og
lights when the headlights turn on
automatically. They will go of f when
the headlights turn of f . Adjust the brightness of the
instrument panel by pressing the
or button with the ignition
switch in the ON (II) position. Press
the button to increase the
brightness and the button to
decrease it.
CONT INUED
Fog L ights
Instrument Panel Brightness
Fog L ights, Instrument Panel Brightness
Inst rument s and Cont rols
143
FOG LIGHT SWITCH
ADJUSTMENT BUTTONS
11/01/14 18:18:18 31TK4630_148
ÎModels equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode
is the equivalent of ON (II). For more
information, see page s 184 and 187.
:
2012 TL

Push the lever up to lock the
steering wheel in that position.
Make any steering wheel
adjustments before you start driving.
Push the lever under the steering
column all the way down.
Move the steering wheel up or
down, and in or out, so it points
toward your chest, not toward
your f ace. Make sure you can see
the instrument panel gauges and
indicators.Make sure you have securely
locked the steering wheel in place
by trying to move it up, down, in,
and out.
1.
2. 3.
4.
Steering Wheel A djustments
146
LEVER
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.
11/01/14 18:18:42 31TK4630_151
Inst rument s and Cont rols
2012 TL

Î
Î Î
CONT INUED
Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Use
only Acura-approved key blanks.The immobilizer system protects
your vehicle f rom thef t. If an
improperly coded key or keyless
access remote (or other device) is
used, the engine’s f uel system is
disabled.
When you turn the ignition switch to
the ON (II) position, or select the
ON mode with the engine start/
stop button, the immobilizer system
indicator should come on brief ly,
then go off. If the indicator starts to
blink, it means the system does not
recognizethecodingof thekeyor
keyless access remote.
On models without keyless access
system, turn the ignition switch to
the LOCK (0) position, remove the
key, reinsert it, and turn the ignition
switch to the ON (II) position again.On models with keyless access
system, set the power mode to
VEHICLE OFF (LOCK), then select
theONmodeagain.
The system may not recognize your
key’s or remote’s coding if another
immobilizer key or other metal
object (i.e. key chain) is near the
ignition switch or the keyless access
remote when you insert the key or
set the power mode to ON.
Keys and Locks, Immobilizer System
Immobilizer System
Inst rument s and Cont rols
149
11/01/14 18:19:12 31TK4630_154
Your vehicle has the engine
stop button instead of an
See page
187 for
conventional power switches
engine start/stop button. For more
information on
see page 184. start/
ignition switch.
a comparison between and your
selecting the power mode,
Î
:On models with keyless access system
2012 TL

µ
µ
µ
µ If the f ront wheels are turned, the
anti-theft lock may make it difficult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
You can
operate the audio system and the
accessory power sockets in this
position.
This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom the
ACCESSORY (I) to the ON (II)
position. You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or the
ACCESSORY (I) position and open
the driver’s door. Remove the key to
turn of f the beeper.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key.
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III). You will also see a ‘‘REMOVE KEY’’
message on the multi-information
display.
TheshiftlevermustbeinPark
bef ore you can remove the key f rom
the ignition switch.
You can insert or
remove the key only in this position.
To turn the key, you must push the
key in slightly. The shif t lever must
also be in Park. Go to page f or inf ormation on
the engine start/stop button.
184
On models without keyless access
system
On models with keyless access system
A CCESSORY (I)
ON (II)
ST A RT (III)
LOCK (0)
Ignition Switch
Inst rument s and Cont rols
151
11/01/14 18:19:33 31TK4630_156
2012 TL

µ
Î
CONT INUED
See pages f or important saf etyinf ormation and warnings about how toproperly position the seats and seat-backs.
Driver’s seat only:
1513
The passenger seat has the same
adjustments as the driver’s seat but
without any lumbar adjustment.
Raises or lowers the seat.Moves the whole seat up
and f orward, or down
and backward. The front
of the seat also tilts up or
down at the same time.
Adjusts the seat-back
angle f orward or
backward.
The controls f or the power
adjustable front seats are on the
outside edge of each seat bottom.
You can adjust the seats with the
ignition switch in any position.
Make all seat adjustments bef ore
you start driving.
Moves the seat forward
and backward.
Moves the f ront of the
seat up or down.Increases or decreases
the lumbar support.
Seats
Front Seat Power A djustments
Inst rument s and Cont rols
161
Driver’s seat
11/01/14 18:21:42 31TK4630_166
Î
Models equipped with the keyless access
system have an engine start/stop button instead of
an ignition switch. VEHICLE OFF (LOCK) Mode
is the equivalent of LOCK (0), ACCESSORY Mode
is the equivalent of ACCESSORY (I), and ON
Mode is the equivalent of ON (II). For more
information, see pages
:
184 and 187.
2012 TL

Î
Both outside door mirrors have a
reverse tilt f eature. When in
reverse, the selected mirror will
tilt down slightly to improve your
view as you parallel park. Shifting
out of reverse will return the
mirror to its original position.To tilt the driver’s mirror, place
the selector switch in the left
position.
To tilt the passenger’s mirror,
place the switch in the right
position.
To turn the feature off, place the
switch in the center position.
When you f inish, move the
selector switch to the center (off)
position. This turns the
adjustment switch of f to keep your
settings.
Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown. With the ignition switch in the
ON (II) position, move the
selector switch to the L (driver’s
side), or R (passenger’s side). Outside mirror positions can be
stored in the driving position
memory system (see page ). 3.
1.
2. 170
Adjusting the Power Mirrors
Reverse Tilt Door Mirror
Mirrors
168
ADJUSTMENT SWITCH
SELECTOR SWITCH
11/01/14 18:22:53 31TK4630_173
Inst rument s and Cont rols
Î
Models equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode
is the equivalent of ON (II). For more
information, see
page s 184 and 187.
:
2012 TL

ÎÎ
This heated mirror f unction has a
timer (see page ).
The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, or the power mode ON,
turn on the heaters by pressing the
button. The indicator in the button
comesonasareminder.Pressthe
button again to turn the heaters off.
Pressing this button also turns the
rear window def ogger on and of f . If the outside temperature is below
41°F (5°C), the heated mirror
function will come on automatically
f or 10 minutes when you turn the
ignition switch to the ON (II)
position.
145
Mirrors
Power Mirror Heaters
Inst rument s and Cont rols
169
HEATED MIRROR BUTTON
11/01/14 18:23:02 31TK4630_174
Î
Models equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode
is the equivalent of ON (II). For more
information, see
page s 184 and 187.
:
2012 TL