2012 Acura TL key

Î
Although your tire pressure is
monitored, you must manually check
thetirepressuresmonthly.
Each tire, including the spare, should
be checked monthly when the
vehicle is cold, and set to the
recommended inflation pressure as
specified on the vehicle placard and
in the owner’s manual (see).
For example, if you check and f ill
your tires in a warm area, then drive
in extremely cold weather, the tire
pressure will be lower than
measured and could be underinf lated
and cause the low tire pressure/
TPMS indicator to come on. Or, if
youcheckandadjustyourtire
pressure in cooler conditions, and
drive into extremely hot conditions,
the tire may become overinf lated.
However, the low tire pressure/
TPMS indicator will not come on if
thetiresareoverinflated.
Refer to page for tire inflation
guidelines.
If there is a problem with the TPMS,
this indicator begins to f lash. It stops
flashing after approximately 1
minute, then stays on. You will also
see a ‘‘CHECK TPMS SYSTEM’’
message on the multi-inf ormation
display (see page ). Toselectthetirepressuremonitor,
press the INFO button several times
with the ignition switch in the ON
(II) position or with the power mode
ON.
You will see the above display on the
multi-inf ormation display when each
tire pressure is normal.
517
568
CONT INUED
Tire Pressure Monitor
Tire Pressure Monitoring System (TPMS)
Driving
515
U.S.
Example: Technology Package is shown.
11/01/14 19:24:39 31TK4630_520
page 570
ÎModels equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode

is the equivalent of ON (II). For more
information, see page s 184 and 187.
:
2012 TL

ÎÎ
To turn the system off, press and
hold the BSI OFF button when the
ignition switch is in the ON (II)
position. The BSI indicator on the
instrument panel glows amber,
indicating that the system is turned
of f . The multi-inf ormation display
indicates that the system is of f .To turn the system on again, press
and hold the same button. The BSI
indicator on the instrument panel
turns off. The multi-information
display indicates that the system is
on.
When the ignition switch is turned
to the ON (II) position, the system
will be in the previously selected ON
or OFF setting.
Blind Spot Inf ormation System (BSI)
BSI OFF Button
Driving
525
U.S. model is shown.
Canadian model is shown.
11/01/14 19:26:13 31TK4630_530
Î
Models equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode
is the equivalent of ON (II). For more
information, see
page s 184 and 187.
:
2012 TL

µ
Î
Î
ÎÎ
Multi-Inf ormationDisplay Message BSI Indicator
System
Status
ON
OFF
ON/OFF OFF Description
2
When you press and hold the BSI OFF button with the ignition switch in the ON (II) position, a
BSI ON or OFF message is displayed on the multi-information display for about 5 seconds.
The BSI indicator will remain on while the system is off.
The BSI alert indicator illuminates or flashes according to the system status.
A chime sounds to indicate that the system has been turned ON or OFF.
If while driving, mud, snow, or ice accumulates in the vicinity of sensor:
The system may shut down
The BSI indicator illuminates, a message is displayed on the multi-information display, and a
chime sounds.
The BSI indicator will turn off and the system will return to normal once the obstacle is removed,
and you begin to drive.
Always keep the area around the radar sensors clean. BSI may not operate properly if the sensors
are obstructed.
The BSI alert indicator: May come on when a vehicle enters one of the alert zones, even if this message is displayed.
May not come on due to obstruction (splashes, etc.) even if this message is not displayed.
2:
If the system is faulty, the BSI indicator illuminates and a message is displayed on the multi-
information display.
Have your vehicle inspected by your Acura dealer.
1
Blind Spot Inf ormation System (BSI)
BSI Status Displays
526
11/01/14 19:26:25 31TK4630_531
Driving
1: ON mode on models with keyless access system (see pages 184 and 187).
System status may remain on even when the BLIND SPOT NOT AVAILABLE messa\
ge is displayed.
2012 TL

Î
CONT INUED
Your vehicle displays engine oil lif e
and maintenance service items on
the multi-information display to show
youwhenyoushouldhaveyour
dealer perf orm engine oil
replacement and indicated
maintenance service.To see the current engine oil lif e
displayed on the multi-inf ormation
display, turn the ignition switch to
the ON (II) position, and press the
SEL/RESET button on the steering
wheel repeatedly until the engine oil
lif e is displayed.
Based on the engine operating
conditions, the onboard computer in
your vehicle calculates the remaining
engine oil lif e and displays it as a
percentage.
Maintenance Minder
Engine Oil L if e Display
Maint enance
531
REMAINING ENGINE OIL LIFE
U.S. model is shown.
TM
11/01/14 19:27:06 31TK4630_536
Î Models equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode
is the equivalent of ON (II). For more
information, see
page s 184 and 187.
:
2012 TL

ÛÝ
Î
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ µ
µ
Pressing either INFO button ( / )
switches the display f rom the
message to another display. Once
you switch the display, this message
will go of f .
Along with the message, the system
message indicator comes on (see
page ).
When the remaining engine oil lif e is
15 to 6 percent, the multi-inf ormation
display shows a ‘‘SERVICE DUE
SOON’’ message along with the
maintenance item code(s) indicating
themainandsubitemsrequiredat
thetimeof theoilchange.Referto
page f or a complete list of the
maintenance main items and sub
items.
The remaining engine oil lif e is
shown on the multi-inf ormation
display according to this table:
The message appears on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position.72
540
Calculated Engine Oil Lif e (%)
100% 91% 90% 81%
80% 71%
70% 61%
60% 51%
50% 41%
40% 31%
30% 21%
20% 16%
15% 11%10% 6% 5% 1% 0% Displayed
Engine Oil Lif e (%) 100%90%
80%
70%
60%
50%
40%
30%
20%
15%
10%5%
0%
Maintenance Minder
532
MAINTENANCE MAIN ITEM CODE
MAINTENANCE SUB ITEM CODE(S)
TM
11/01/14 19:27:17 31TK4630_537
Maint enance
Î
Models equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode
is the equivalent of ON (II). For more
information, see
page s 184 and 187.
:
2012 TL

Î
ÛÝ
CONT INUED
Press the SEL/RESET button on the
steering wheel repeatedly to select
the engine oil lif e. The message
‘‘SERVICE,’’ along with ‘‘0%,’’ and the
maintenance item code are displayed
on the multi-information display
when the calculated engine oil lif e is
0to1percent.
These messages will come on every
time you turn the ignition switch to
the ON (II) position.
If the indicated required service is
not done and the remaining engine
oil lif e becomes 0%, the multi-
inf ormation display will show a
‘‘SERVICE PAST DUE’’ message,
the total distance traveled after the
remaining oil lif e became 0%, and the
maintenance item code(s).
Pressing either INFO button ( / )
switches the display f rom the
message to another display. To see
the message again, press either
INFO button repeatedly. Immediately have the service
perf ormed, and make sure to reset
the display as described on page .
537
Maintenance Minder
Maint enance
535
U.S.TOTAL PAST DUE DISTANCE
TRAVELED
MAINTENANCE CODES
Canada
TM
11/01/14 19:27:42 31TK4630_540
Î Models equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode
is the equivalent of ON (II). For more
information, see
page s 184 and 187.
:
2012 TL

ÎÎ
Û
Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100%’’ on the display the
next time you turn the ignition
switch to the ON (II) position.
Turn the ignition switch to the
ON (II) position.
If maintenance service is done by
someone other than your dealer,
reset the Maintenance Minder as
f ollows: If the engine oil lif e is not
displayed, press the SEL/RESET
buttononthesteeringwheel
repeatedly.
Press and hold the SEL/RESET
button on the steering wheel f or
more than 10 seconds. The
remaining engine oil lif e reset
mode will be shown on the multi-
inf ormation display.
Select ‘‘RESET’’ by pressing the
INFO ( ) button, then press the
SEL/RESET button to reset the
engine oil lif e display. The
maintenance item code(s) will
disappear, and the engine oil lif e
will reset to ‘‘100.’’ If you want to
cancel the oil lif e reset mode,
select ‘‘CANCEL.’’
3. 1.
2.
4.
Maintenance Minder
Resetting the Engine Oil Lif e
Display
Maint enance
537
TM
11/01/14 19:28:02 31TK4630_542
ÎModels equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode

is the equivalent of ON (II). For more
information, seepage s 184 and 187.
:
2012 TL

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk, readjustment may be required.
Adjustmentsshouldbedonebyyour
dealer or another qualif ied
technician.Your vehicle has halogen high beam
headlight bulbs which are also used
f or the daytime running light.
Handle it by its base and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Open the hood.
Remove all engine compartment
covers (see page ).
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch off
and the key removed (or the vehicle
is in VEHICLE OFF (LOCK) mode
on models with keyless access
system). Because of this, you
should not attempt to examine or
change a low beam headlight
bulb yourself. If a low beam
headlight bulb fails, take the vehicle
to your dealer to have it replaced.
If youarereplacingthebulbon
the driver’s side, remove the
holding clips with a f lat-tip
screwdriver. Then remove the
upper part of the air intake duct by
pulling it straight up.
1.
2. 542
CONT INUED
Headlight A iming
L ow Beam Headlight Bulb
Replacement Replacing a High Beam
Headlight/Daytime Running
Light Bulb
Lights
Maint enance
555
HOLDING CLIP
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
11/01/14 19:31:11 31TK4630_560
2012 TL