2012 ACURA RL ECU

Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
Insert the dipstick all the way into
the transmission as shown.
Remove the dipstick and check
the f luid level. It should be
between the upper and lower
marks.
If the level is below the lower
mark, add f luid into the dipstick
hole to bring it to the level
between the upper and lower
marks.Pour the f luid slowly and caref ully so
you do not spill any. Clean up any
spill immediately; it could damage
components in the engine
compartment.
If youarenotsurehowtoaddfluid,
contact your dealer. The transmission should be drained
andrefilledwithnewfluidwhenthis
service is shown by a maintenance
message on the multi-inf ormation
display.Make sure the rubber cap on the
dipstick f its in the dipstick guide
and that you push the dipstick in
all the way. Always use Acura ATF DW-1
(automatic transmission f luid).
5.6.
3.
4.
Automatic Transmission Fluid
Maint enance
465
UPPER
MARK
LOWER
MARKGUIDE
Use only Acura ATF DW-1 (automatic
transmission f luid). Do not mix with
other transmission f luids.
Using transmission f luid other than
Acura ATF DW-1 may cause
deterioration in transmission operation
and durability, and could result in
damage to the transmission.
Damage resulting f rom the use of
transmission f luid other than Acura
AT F DW-1 is not covered by the Acura
new vehicle warranty.
11/07/20 19:01:13 31SJA670_470
ProCarManuals.com

Carefully pry in the top or bottom
edge of the trim with a small f lat-
tip screwdriver, and pull the trim
straight back. Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.
Pull the taillight assembly straight
back out of the body. Remove the two mounting bolts
with an 8 mm wrench. Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two undercover bolts
on the side under cover and
tighten them securely. Put the
holding clip back on the side
undercover and push on the center
until it locks (the center is f lush
with the head).
2. 1. 3.
4.
5. 5.
6.
7.
8.
CONT INUED
Replacing a Rear Turn Signal
Light Bulb
Lights
Maint enance
473
MOUNTING NUT
MAINTENANCE LIDTAIL LIGHT TRIMBOLTS
11/07/20 19:02:33 31SJA670_478
ProCarManuals.com

Open the trunk.
Remove the light assembly cover
by pulling its outside edge. Install the new bulb in the socket
bypushingitstraightinthesocket
until it bottoms.
Reinstall the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.
When reinstalling the taillight
assembly, align and pop the snap
f asteners in place. Tighten the two
mounting bolts and reinstall the
trim in place.
Tighten the mounting nut securely,
and reinstall the maintenance lid. Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.9. 8.
1.
2.
12. 11. 10.
6.
7.Replacing a Back-up L ight Bulb
Lights
474
SOCKETBULBCOVERS
11/07/20 19:02:42 31SJA670_479
ProCarManuals.com

Examine the new wiper blades. If
they have no plastic or metal
reinf orcement along the back
edge, remove the metal
reinf orcement strips f rom the old
wiper blade, and install them in
the slots along the edge of the new
blade.Slide the new wiper blade into the
holder until the tabs lock.
Reinstall the blade assembly to the
wiper arm and tighten the two
screws securely. Reinstall the
cover by pushing it in.
Set the wiper arms back on the
windshield. Adjust the windshield
wipers to their previously parked
position.
Remove the blade f rom its holder
by grabbing the tabbed end of the
blade. Pull up f irmly until the tabs
come out of the holder. 4. 5.6.
7.
8.
Wiper Blades
Maint enance
479
BLADE
BLADE
REINFORCEMENT
11/07/20 19:03:19 31SJA670_484
ProCarManuals.com

´ Tires marked ‘‘M S’’ or ‘‘All
Season’’ on the sidewall have an all-
weather tread design suitable for
most winter driving conditions.
For the best perf ormance in snowy
or icy conditions, you should install
snow tires or tire chains. They may
be required by local laws under
certain conditions.If you mount snow tires on your
vehicle, make sure they are radial
tires of the same size and load range
as the original tires. Mount snow
tires on all f our wheels. The traction
provided by snow tires on dry roads
maybelowerthanyouroriginaltires.
Check with the tire dealer f or
maximum speed recommendations.Mount tire chains on your tires when
required by driving conditions or
local laws. Install them only on the
f ront tires.
Because your vehicle has limited tire
clearance, Acura strongly
recommends using the chain listed
below, made by Security Chain
Company (SCC).
Cable-type: SCC Radial Chain
SC1040 Winter Driving
Snow T ires T ire Chains
Tires
488
11/07/20 19:04:30 31SJA670_493
ProCarManuals.com

If your vehicle’s battery is
disconnected or goes dead, all stored
driving positions will be lost. To
store the driving positions again, see
the storing procedure on page .
The navigation system will also
disableitself.Thenexttimeyouturn
on the ignition switch, the system
will require you to enter a PIN
bef ore it can be used. Ref er to the
navigation system manual.If your vehicle’s battery is
disconnected or goes dead, the audio
system may disable itself . The next
timeyouturnontheradioyouwill
see ‘‘ ’’ in the f requency
display. Use the preset buttons to
enter the code (see page ).
If your vehicle’s battery is
disconnected or goes dead, the
power tilt and telescopic steering
wheel system will be disabled. The
system needs to be reset af ter
reconnecting the battery (see page
). The compass system will also disable
itself.Thenexttimeyouturnonthe
ignition switch, the system will
require you to enter a PIN bef ore it
can be used. Enter the f our-digit anti-
theftsecuritycode(seepage ).
You will also need to reset the clock
according to the instruction of
setting the clock (see page ).298
313280
149 164
On vehicles with navigation systemOn vehicles without navigation system
Checking the Battery
Maint enance
491
11/07/20 19:04:48 31SJA670_496
ProCarManuals.com

To reinstall the cover, reinstall the
two holding clips and secure them
bypushingonthecenterof each
f astener head.
Turn the knob of the cover to
LOCK position as shown in the
illustration.
Turn the knob of the battery cover
toUNLOCKasshowninthe
illustration.Remove the holding clips by
pushingonthecenterof each
f astener head. 2.3.
4.
1.
:
:
Removing the Battery Cover
Checking the Battery
492
KNOBCLIPS
Push to reset/install clip Push to remove clip Unlock
Lock
11/07/20 19:04:55 31SJA670_497
ProCarManuals.com

Store the jack and tools in the tool
case. Place the tool case in the f lat
tire.
Tighten the wheel nuts securely in
the same crisscross pattern. Have
the wheel nut torque checked at
the nearest automotive service
f acility.
Tighten the wheel nuts to:Place the flat tire face down in the
spare tire well.
Wrap the spacer cone and spare
tire wing bolt with cloth or paper,
and store them in the spare tire
well.Lower the trunk f loor, then close
the trunk lid.
Your vehicle’s original tire has a
tire pressure monitoring system
sensor. To replace a tire, ref er to
(see
page ). 14. 13.
15.16.
17.
18.
430
Changing a Flat T ire
Changing a T ire with T PMS
500
WING BOLTSPACER CONE
94 lbf·ft (127 N·m , 13 kgf·m)Loose items can fly around the
interior in a crash and could
seriously injure the occupants.
Store the wheel, jack, and tools
securely before driving.
11/07/20 19:05:53 31SJA670_505
ProCarManuals.com