2012 ACURA RL key

The handle of each f ront door has a
sensor. That sensor works with the
remote so you can automatically
unlock/lock the door(s).
By def ault, only the driver’s door
unlocks when you grab its handle.If a remote is within operating range
while you wash your vehicle or when
it is raining heavily, the door sensors
may respond by unlocking the doors.
The unlock sensors do not operate
when:
Theremoteisnotwithinthe
operating range.
The remote is too close to the
vehicle.
When the doors are unlocked.
Theremotebatteryisdead.
The vehicle battery is dead.
If you do not open any of the doors
within 30 seconds, they will
automatically relock. If you wear a glove while grabbing a
f ront door handle, the door sensor
maybeslowtorespondormaynot
respond by unlocking the doors. To change the ‘‘KEYLESS ACCESS
BEEP’’ setting, see page . To change the ‘‘KEYLESS ACCESS
LIGHT FLASH’’ setting, see page
. When you unlock the door(s), some
exterior lights blink twice and the
system beeps twice. All the doors unlock when you grab
the handle of the f ront passenger’s
door. To change the ‘‘DOOR UNLOCK
MODE’’ setting, see page .
To unlock the remaining doors and
the trunk, press the UNLOCK
button on the remote or the rear of
the master door lock switch on the
driver’s door.109
111
113 Unlocking the Door(s)
K eyless A ccess System
Inst rument s and Cont rols
169
11/07/20 18:21:30 31SJA670_174
ProCarManuals.com

Each f ront door has a LOCK/
UNLOCK f eature.
When you touch the door lock
sensor of the f ront door by hand, all
the doors and the trunk will lock.The lock sensors do not operate if :
When you lock the doors, some
exterior lights blink once and thesystem beeps once. When you
cannot set the security system
because the trunk or hood is open,
no exterior light blinks and/or no
beeper sounds.
Bef ore locking the doors, make sure
theremoteisnotinsidethevehicle.If a remote is within operating range
while you wash your vehicle or when
it is raining heavily, the door sensors
may respond by locking the doors. Within 2 seconds of touching the
handle to lock the doors or locking
the doors with remote, pull the
handletomakesurethedoorsare
actually locked. The door unlock
sensors do not operate f or about 2
seconds af ter the doors are locked. To change the ‘‘KEYLESS ACCESS
BEEP’’ setting, see page . To change the ‘‘KEYLESS ACCESS
LIGHT FLASH’’ setting, see page
.If you touch the door lock sensor of
the f ront door with your hand
wearing a glove, the door sensor may
delay to respond or not respond by
locking the doors.
Theremoteisnotwithinthe
operating range.
The doors are open.
The ignition switch is not in the
LOCK (0) position.
The built-in key is in the ignition
switch.
The remote is too close to the
vehicle.
Theremotebatteryisdead.
The vehicle battery is dead. 111
113 L ocking the Doors
K eyless A ccess System
170
DOOR LOCK SENSOR
11/07/20 18:21:43 31SJA670_175
ProCarManuals.com

Bef ore closing the trunk, make sure
theremoteisnotinthetrunk.
If you close the trunk when the
remote is in it, the system beeps, and
the trunk reopens.
When you close the trunk with all
doors locked, the trunk will lock.
When you unlock all the doors with
the remote, built-in key or power
door lock master switch, the trunk
will unlock.
Use the pull handle when you close
the trunk. If you open a door, pull its lock tab,
and shut it when the remote is inside
the vehicle, the driver’s door will
unlock. Make sure you carry the
remote with you when you lock the
doors.
This function is also activated on the
f ront passenger’s door. If you open
the f ront passenger’s door, and shut
it af ter pulling its lock tab rearward
whentheremoteisinsidethevehicle,
all doors will unlock.Locking the TrunkDoor L ock Prevent ion
K eyless A ccess System
Inst rument s and Cont rols
171
PULL HANDLE
11/07/20 18:21:51 31SJA670_176
ProCarManuals.com

µµ
µ You cannot lock the doors if any
door is not f ully closed, if the built-in
key is in the ignition switch, or if the
ignition switch is in any position
except the LOCK (0) position.
When you cannot set the security
system because the trunk or hood is
open, no exterior light blinks and/or
no beeper sounds.
Press this button once
to unlock the driver’s door. Press it
twice to unlock the other doors.
Some exterior lights will f lash twice
each time you press the button. The
ceiling light (if the ceiling light
switch is in the DOOR position) will
come on when you press the
UNLOCK button. If you do not open
any door within 30 seconds, the
ceiling light f ades out. If you relock
the doors with the remote before 30
seconds have elapsed, the ceiling
light will go of f immediately.To change the ‘‘DOOR LOCK
MODE’’ setting, see page .
To change the ‘‘INTERIOR LIGHT
DIMMING TIME,’’ see page .
If you unlock the doors with the
remote, but do not open any door
within 30 seconds, the doors
automatically relock and the security
system sets.
To change the ‘‘SECURITY
RELOCK TIMER’’ setting, see page
.
To change the ‘‘KEYLESS LOCK
ACKNOWLEDGMENT’’ setting, see
page .
You can also open all power windows
and the moonroof f rom outside the
vehicle with the remote transmitter
(see page ).Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk if the
built-in key is in the ignition or the
ignition switch is in any position
except the LOCK (0) position. You
cannot open the trunk with the
remote if the trunk main switch is
turned off.
Pressthisbuttonfor
about 2 seconds to attract attention:
the horn will sound and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote. 127
116
129 131
188
K eyless A ccess System
UNL OCKTRUNK
PA NIC
Inst rument s and Cont rols
173
11/07/20 18:22:11 31SJA670_178
ProCarManuals.com

The driving position memory
activated (Driver 1, Driver 2) is
shownonthebackof eachremote.
Make sure you store your desired
driving position in the memory thatis activated by the remote you
normally carry.
When you unlock the driver’s door
with your remote transmitter, each
remote transmitter activates the
customized settings related to that
remote.To turn of f this f eature, press and
hold the LOCK and UNLOCK
buttonsatthesametime.TheLED
in the remote will blink once. Then
release the buttons. Doing this
cancels the keyless memory settings
f or that remote and restores the
def ault settings.
Some of them keep the same
settings as they were set previously.
To turn the keyless memory settings
back on, repeat this procedure. The
LED will blink twice to indicate the
f eature has been turned on.
When you unlock and open the
driver’s door with the remote, the
driver’s seat (except power lumbar)
and outside mirrors move to the
positions stored in memory. An
indicator on one of the driving
position memory buttons on the
driver’s door also comes on. Navigation system pref erences
(see the navigation system
manual). Here are the settings activated with
the remote:
Driving position memory
(see page ).
Customized settings
(see page ).
Audio system settings
(see page ).
Climate control settings
(see page ).
Compass system pref erences
(see page ).164
81
213
205
281
U.S. RL model
Except U.S. RL model
K eyless A ccess System
Recalling a Memorized Driving
Position
174
DRIVER’S ID
11/07/20 18:22:22 31SJA670_179
ProCarManuals.com

´ Replace the old batteries with new
batteries. Place the batteries so the
side is f acing up. Snap the two
halvesof theremotecaseback
together.
An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations f or
battery disposal. Replace the batteries if necessary.
Battery type: CR2025
Remove the built-in key.
Place a cloth on the edge to prevent
scratches, then remove the upper
half by caref ully prying on the edge
with a coin. You will also see the ‘‘DRIVER 1’’ or
‘‘DRIVER 2’’ message on the multi-
inf ormation display, depending on
which linked remote transmitter is
used.
Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperatures.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
CONT INUED
Replacing the Remote Battery
Remote Transmitter Care
K eyless A ccess System
Inst rument s and Cont rols
175
11/07/20 18:22:32 31SJA670_180
ProCarManuals.com

If the ignition switch cannot be
turned f rom the LOCK (0) position
to the ACCESSORY (I) position afterthe beep, the steering wheel is
locked. To unlock the steering wheel,
turn it right and lef t while turning
the ignition switch at the same time.
If theremoteandthevehicledonot
recognize each other, turn the
ignition switch to the LOCK (0)
position, remove the ignition switch
cover, insert the built-in key, and
turn the switch (see pages and
).
When you push the ignition switch,
theremoteandthevehiclerecognize
each other. Af ter the recognition,
the remote indicator f lashes, and a
beeper sounds once. Af ter the beep,
turn the ignition switch.
When the remote is out of the
operating range, the ignition switch
is locked.151
178
CONT INUED
Ignition Switch
K eyless A ccess System
Inst rument s and Cont rols
177
Make sure you know where the remote
is when you are inside the vehicle.
Remember that you can start the engine
without using the built-in key when the
remote is inside the vehicle.
Make sure you always carry the remote
with you.
11/07/20 18:22:47 31SJA670_182
ProCarManuals.com

To remove the ignition switch cover,
insert the built-in key (see page ),
then pull the cover out by pulling the
built-in key while pushing it. Also, if you close the door when the
ignition switch is not in the LOCK
(0) position and the remote is not
inside the vehicle, the keyless access
alarm sounds outside the vehicle, a
message appears on the multi-
inf ormation display, and the beeper
sounds if the ignition switch is in the
ON (II) position.
When the beeper sounds af ter you
close the driver’s door outside the
vehicle, check the position of the
ignition switch and the location of
the remote.
If the engine is running and you
removetheremotefromthevehicle,
it will continue to run. But once
turned to the LOCK (0) position, the
engine will not restart until a remote
is brought back into the vehicle. To turn the ignition switch to the
LOCK (0) position, put the
transmission in Park, press the
switch in, and turn it to the LOCK
(0) position. When the transmission
is not in Park, you cannot turn the
ignition switch to the LOCK (0)
position.
Bef ore leaving the vehicle, make
sure the ignition switch is in the
LOCK (0) position.
If you open the driver’s door with the
ignition switch in the ACCESSORY
(I) position, a beeper will sound.
You will also see a ‘‘RETURN
IGNITION SWITCH TO LOCK (0)
POSITION’’ message on the multi-
inf ormation display.181
K eyless A ccess System
Removing the Ignition Switch
Cover
178
BUILT-IN KEY IGNITION SWITCH COVER
pushpull
11/07/20 18:22:55 31SJA670_183
ProCarManuals.com