2012 ACURA RL clock

To adjust the hour, turn the interface
knob, then press ENTER.Turn the interface knob to adjust the
minute.
Press ENTER to set the time. The
screen will return to the
screen (see page ). To adjust the minute, push the
interf ace knob to the right to display
the adjustment screen f or MINUTE. 313
Compass Syst em (U.S. model wit hout navigat ion syst em)
Clock
adjustment
314
11/07/20 18:40:38 31SJA670_319
ProCarManuals.com

When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise. Lift up the lid on the front
bulkhead cover f rom the f ront.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pourthecoolantslowlyand
caref ully so you do not spill any.
Clean up any spill immediately; it
could damage components in the
engine compartment.
Put the radiator cap back on, and
tighten it fully.
3. 2. 1.4.
5.
Engine Coolant
462
LID
RADIATOR CAP
11/07/20 19:00:50 31SJA670_467
ProCarManuals.com

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise. If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ). Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ). Open the hood. Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Reinstall the engine compartment
side cover.
Reinstall the battery cover. (Driver’s side) 2.
3. 1.
4.5.
6.
7.
8.
9. 457
492
Lights
Maint enance
469
BULB
CONNECTOR
11/07/20 19:01:48 31SJA670_474
ProCarManuals.com

Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the bulb in slightly, and turn
it counterclockwise. Open the hood.
If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ).Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Reinstall the engine compartment
side cover.
(Driver’s side)
Reinstall the battery cover. 2. 1.
3.
4.5.
6.
7.
457
4928.
9.
Lights
Replacing a Front T urn Signal
Light Bulb
470
BULB SOCKET
11/07/20 19:01:59 31SJA670_475
ProCarManuals.com

Remove the left or right side
engine compartment cover (see
page ).
Use a f lat-tip screwdriver to
remove the holding clip f rom the
windshield washer reservoir. (Passenger’s side) Open the hood.
If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ).
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Turn on the lights to make sure
the new bulb is working.
Reinstall the engine compartment
side cover. Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Reinstall the windshield washer
reservoir.
(Driver’s side)
Reinstall the battery cover. (Passenger’s side) 1.
2.
3.
4.
5.6.
7.
8.
9. 457
492
10.
Lights
Replacing a Front Parking/Side
Marker Bulb
Maint enance
471
SOCKET
BULB
CLIP
11/07/20 19:02:13 31SJA670_476
ProCarManuals.com

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise. Use a Phillips-head screwdriver to
remove the two undercover bolts,
and remove the holding clip with a
f lat-tip screwdriver.
Caref ully push up the side under
cover into the bumper. Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Thefoglightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustment should
be done by your dealer or another
qualif ied technician.3.
4. 1.
2.
Lights
ReplacingaFogLightBulb
472
CLIP
CONNECTOR BOLTS
BULBHalogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
11/07/20 19:02:22 31SJA670_477
ProCarManuals.com

Carefully pry in the top or bottom
edge of the trim with a small f lat-
tip screwdriver, and pull the trim
straight back. Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.
Pull the taillight assembly straight
back out of the body. Remove the two mounting bolts
with an 8 mm wrench. Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two undercover bolts
on the side under cover and
tighten them securely. Put the
holding clip back on the side
undercover and push on the center
until it locks (the center is f lush
with the head).
2. 1. 3.
4.
5. 5.
6.
7.
8.
CONT INUED
Replacing a Rear Turn Signal
Light Bulb
Lights
Maint enance
473
MOUNTING NUT
MAINTENANCE LIDTAIL LIGHT TRIMBOLTS
11/07/20 19:02:33 31SJA670_478
ProCarManuals.com

Open the trunk.
Remove the light assembly cover
by pulling its outside edge. Install the new bulb in the socket
bypushingitstraightinthesocket
until it bottoms.
Reinstall the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.
When reinstalling the taillight
assembly, align and pop the snap
f asteners in place. Tighten the two
mounting bolts and reinstall the
trim in place.
Tighten the mounting nut securely,
and reinstall the maintenance lid. Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.9. 8.
1.
2.
12. 11. 10.
6.
7.Replacing a Back-up L ight Bulb
Lights
474
SOCKETBULBCOVERS
11/07/20 19:02:42 31SJA670_479
ProCarManuals.com