2012 Abarth Punto Evo wipers

52
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
The wiper stops working three strokes after the stalk is
released. A further stroke 6 seconds later completes
the wiping operation.
RAIN SENSOR
(for versions/markets where provided)
The rain sensor is located behind the rear view mirror
in contact with the windscreen and has the purpose of
automatically adjusting the frequency of the windscreen
wiper strokes depending on the intensity of the rain
during intermittent operation.
IMPORTANT Keep the glass in the sensor area clean.
Activation
Move the twist switch on the right-hand stalk to
≤fig.
38. The activation of the sensor is signalled by a wiper
stroke. Through the setup menu it is possible to
increase the sensitivity of the rain sensor. The increasing
of the rain sensor sensitivity is signalled by a “stroke” to
show the command has been acquired. If the
windscreen washer is used with the rain sensor
activated, the normal washing cycle is performed, after
which the rain sensor resumes its normal automatic
operation.
Never use the windscreen wipers to
remove layers of snow or ice from the
windscreen. In such conditions, the
windscreen wipers may be subjected to excessive
stress and the motor protection which prevents
operation for a few seconds may intervene. If
operation is not restored, even after turning the
key and restarting the engine, go to an Abarth
Dealership.
When released, the stalk returns to its default position
and the wipers automatically switch off.
With the twist switch at
≤, the windscreen wiper will
automatically adapt to the speed of the car.
IMPORTANT Replace the wiper blades as specified in
the “Maintenance and care” section.
“Smart washing” function
Pull the stalk towards the steering wheel (unstable
position) to operate the windscreen washer.
Keeping the lever pulled for more than half a second,
with just one movement it is possible to operate the
washer jet and the wiper at the same time.

100
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
NO ENGINE CUT-OUT
CONDITIONS
With the device activated, for reasons of comfort,
limiting emissions and safety, the engine does not stop in
certain conditions, including:
❒engine still cold;
❒particularly cold outside temperatures, where the
appropriate indication is provided;
❒battery not sufficiently charged;
❒heated rear window activated;
❒ windscreen wipers working at maximum speed;
❒ driver’s door not shut;
❒ driver’s seat belt not fastened;
❒ reverse gear engaged (for example, during parking
manoeuvres);
❒automatic climate control is on and a comfortable
temperature has not yet been reached or MAX –
DEF function enabled;
❒during the first period of use, to initialise the system.
In the above cases, a message appears in the display and
the warning light fig. 98 flashes in the instrument panel. MANUAL ACTIVATION AND
DEACTIVATION
You can activate/deactivate the Start&Stop device by
pressing the button on the dashboard fig. 96.
When the device is active, the relevant warning light on
the instrument panel switches on fig. 97.
When the system is deactivated, the warning light on
the instrument panel switches on fig. 98.
The relevant device deactivation/activation messages
appear on the reconfigurable multifunction display.
F0U096Abfig. 98

101
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U098Abfig. 99
SAFETY FUNCTIONS
In engine cut-out conditions through the Start&Stop
system, if the driver unfastens his/her seat belt and
opens the driver’s door or the passenger door, the
engine can be restarted only by using the key.
The driver is notified of this condition both by a buzzer
and through an information message in the display and
by the warning light fig. 98 on the instrument panel
flashing.
ENERGY SAVING FUNCTION
(for versions/markets where provided)
If, after the engine has been automatically restarted, the
driver does not take any action for a period of about
three minutes, the Start&Stop system will definitively
stop the engine to avoid fuel consumption. In these
cases, the engine can be restarted only by using the key. RESTARTING CONDITIONS
For reasons of comfort, limiting pollutant emissions and
safety purposes, the power unit can restart automatically
without any action on behalf of the driver if certain
conditions are met, including:
❒battery not sufficiently charged;
❒windscreen wipers working at maximum speed;
❒reduced braking system pressure, e.g. following the
brake pedal being pressed repeatedly;
❒car in motion, for example when driving on steep
roads;
❒stopping the engine through the Start&Stop system
for more than about three minutes;
❒automatic climate control system for establishing a
comfortable temperature or enabling the MAX –
DEF function.
With a gear engaged, the engine can be automatically
restarted only by fully depressing the clutch pedal.
The driver is asked to perform this operation through
a message on the instrument panel and, where provided,
by the warning light fig. 97 on the instrument panel
flashing.
Note If the clutch is not depressed when three minutes
have elapsed since the engine was stopped, the engine
can only be restarted using the key.
Note In cases when the engine stops and this is not
desired, due for example to the clutch pedal being
released sharply with a gear engaged, if the Start&Stop
system is activated, the engine can be restarted by fully
depressing the clutch pedal or by putting the gear lever
into neutral.

136
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
DRIVING STYLE
Starting
Do not warm up the engine at low or high revs when
the car is stationary; this causes the engine to warm up
more slowly, thereby increasing fuel consumption and
emissions. It is therefore advisable to move off
immediately, slowly, avoiding high speeds: in this way the
engine will warm up more quickly.
Unnecessary actions
Avoid accelerating when stopped at traffic lights or
before switching off the engine. The latter action, like
double-clutching, is unnecessary and causes increase of
consumption and pollution.
Gear selection
As soon as the conditions of the traffic and road allow,
use a higher gear. Using a low gear for faster
acceleration will increase consumption. In the same way
improper use of a high gear increases consumption,
emissions and engine wear. Roof rack/ski rack
Remove the roof rack or the ski rack from the roof
after use. These accessories lower air penetration and
adversely affect consumption levels. When transporting
particularly large objects, use a trailer if possible.
Electrical devices
Use electrical devices only for the amount of time
needed. Rear heated window, additional headlights,
windscreen wipers and heater fan need a considerable
amount of energy, therefore increasing the requirement
of current increases fuel consumption (up to +25% in
the urban cycle).
Climate control system
The climate control system is an additional load which
greatly affects the engine leading to higher consumption
(on average up to +20%). When the temperature
outside the car permits it, use the air vents where
possible.
Devices for aerodynamic control
The use of non-certified devices for aerodynamic
control may adversely affect air drag and consumption
levels.

197
RUBBER HOSES
As far as the brake system and fuel rubber hoses are
concerned, follow the “Scheduled Servicing Programme”
in this chapter carefully.
Ozone, high temperatures and prolonged lack of fluid in
the system may cause hardening and cracking of the
hoses, with possible leaks.
Careful inspections are therefore necessary.
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
WINDSCREEN WIPER
BLADES
Periodically clean the rubber part using special products;
TUTELA PROFESSIONAL SC 35 is recommended.
Replace the blades if the rubber edge is deformed or
worn. In any case, it is advisable to replace them
approximately once a year.
A few simple precautions can reduce the possibility of
damage to the blades:
❒make sure that the rubber part is not stuck to the
windscreen at sub-zero temperatures. Use a de-icing
product to release it if required;
❒remove any snow from the glass: in addition to
protecting the blades, this prevents effort from the
motor and overheating;
❒do not operate the windscreen wipers on dry glass.
Driving with worn wiper blades is a
serious hazard, because visibility is
reduced in bad weather.
WARNING