Page 164 of 336
162
CHECKING TYRE PRESSURES / INFLATING
ACCESSORIES
You can also use the compressor, without injecting any product, to:
- check or adjust the pressure of your tyres,
- infl ate other accessories (balls, bicycle tyres...).
)
Turn the selector A
to the "Air" position.
)
Uncoil the black pipe H
fully.
)
Connect the black pipe to the valve of the wheel or
accessory.
If necessary, fi t one of the adaptors supplied with the kit fi rst.
)
Connect the compressor's electrical connector to the vehicle's 12 V
socket.
)
Start the vehicle and let the engine run.
)
Adjust the pressure using the compressor (to infl ate: switch B
in position "I"
; to defl ate: switch B
in position "O"
and press
button C
), according to the vehicle's tyre pressure label or the
accessory's pressure label.
)
Remove the kit then stow it.
Page 168 of 336
166
TOOLS AND SPARE WHEEL *
Depending on the country of sale, the vehicle is equipped with the tools
needed to change a wheel and may also be equipped with a spare
wheel.
The spare wheel is stowed in a protective cover, secured to the boot
fl oor with Velcro
®.
The tools are held in a storage box under the boot fl oor.
Never drive with the rear seat folded when the
spare wheel - or a punctured wheel - is present
in the boot.
Warning marking
"Do not release the backrest of the rear seats!"
*
According to country.
Access to the spare wheel *
)
Open the boot lid.
)
Remove the spare wheel by grasping the grip of its protective
cover.
)
Position the wheel vertically so as to read the warning markings.
)
Remove the Velcro
® located on the tyre tread.
)
Detach the straps, located on each sidewall, then slacken them.
)
Remove the wheel from its protective cover.
When refi tting the wheel into its cover, place it so that the valve is
opposite the strap fi xings.
Page 175 of 336
8/
PRACTICAL INFORMATION
CHANGING A BULB
The headlamps are fi tted with polycarbonate glass with a
protective coating:
)
do not clean them using a dry or abrasive cloth, nor with
a detergent or solvent product,
)
use a sponge and soapy water or a pH neutral product,
)
when using a high pressure washer on persistent marks, do
not keep the lance directed towards the lamps or their edges
for too long, so as not to damage their protective coating and
seals,
)
do not touch the bulb directly with your fi ngers, use lint-free
cloths.
Changing a bulb should only be done after the headlamp has
been switched off for a few minutes (risk of serious burns).
It is imperative to use only anti-ultraviolet (UV) type bulbs in order
not to damage the headlamp.
Always replace a failed bulb with a new bulb with the same type
and specifi cation.
FRONT LAMPS
Model with halogen headlamps
1.
Direction indicators (PY21 W amber).
2.
Dipped beam headlamps (H7 - 55W).
3.
Main beam headlamps (H1 - 55W).
4.
Daytime running lamps / sidelamps (P 21/5 W)
or
Daytime running lamps / sidelamps (LEDs).
Page 180 of 336
178
Changing reversing lamps and foglamps
These two bulbs are changed from outside the rear bumper:
)
unclip the protective cover from the rear, then tilt it,
)
remove it completely to gain access to the two lamp fi xing bolts,
On the left-hand side, take care not to touch the silencer; risk
of burns, if you change the bulb immediately after switching
off the ignition.
)
turn these two bolts one quarter of a turn and remove them,
)
push the lamp towards the inside to unclip it, then tilt it,
)
pull the lamp towards the outside for access to the various
bulb-holders.
- For the reversing lamps: pull the corresponding bulb holder,
- turn the bulb one quarter of a turn and change it.
- For the foglamp: turn the bulb holder one quarter of a turn and
remove it,
- turn the bulb one quarter of a turn and change it.
To refi t, carry out these operations in reverse order.
Page 181 of 336
8/
PRACTICAL INFORMATION
Changing sidelamps and direction indicators
For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualifi ed workshop.
High pressure washing
When using this type of washing on stubborn dirt, do not persist
on the headlamps, the lamps and their surrounds to avoid
damaging their protective coating and seals.
Changing number plate lamps (W5W)
)
Insert the end of the vehicle's key in the hole in the transparent
cover.
)
Push towards the outside to unclip it.
)
Remove the transparent cover.
)
Pull the bulb out and change it.
Changing the third brake lamp (LEDs)
For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualifi ed workshop.
Page 189 of 336
8/
PRACTICAL INFORMATION
TOWING A VEHICLE
TOWING EYE
This is stored in the boot under the fl oor.
For access to it:
)
open the boot,
)
raise the fl oor using the strap,
)
secure it in the vertical position beyond the stops, located on the
sides of the boot,
)
remove the towing eye from the storage box.
GENERAL RECOMMENDATIONS
Observe the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of
the towed vehicle.
The person at the wheel of the towed vehicle must have a valid
driving licence.
When towing a vehicle with all four wheels on the ground, always
use an approved towing bar; rope and straps are prohibited.
When towing a vehicle with the engine off, there is no longer any
power assistance for braking or steering.
In the following cases, you must always call on a professional
recovery service:
- vehicle broken down on a motorway or fast road,
- 4 wheel drive vehicle,
- when it is not possible to put the gearbox into neutral, unlock
the steering, or release the parking brake,
- towing with only two wheels on the ground,
- where there is no approved towing bar available...
Page 190 of 336
188
TOWING YOUR VEHICLE
)
On the front bumper, unclip the cover by pressing at the bottom.
)
Screw the towing eye in fully.
)
Install the towing bar.
)
Place the gear lever in neutral (position N
on the automatic
gearbox).
Failure to observe this instruction could result in damage to certain
components (braking, transmission...) and the absence of braking
assistance the next time the engine is started.
)
Unlock the steering by turning the ignition key one notch and
release the parking brake.
)
Switch on the hazard warning lamps on both vehicles.
)
Move off gently and drive slowly and for a short distance only.
TOWING ANOTHER VEHICLE
)
On the rear bumper, unclip the cover by pressing at the bottom.
)
Screw the towing eye in fully.
)
Install the towing bar.
)
Switch on the hazard warning lamps on both vehicles.
)
Move off gently and drive slowly and for a short distance only.
Page 191 of 336
8/
PRACTICAL INFORMATION
TOWING A TRAILER
Towbar suitable for the attachment of a trailer with additional lighting
and signalling.
Your vehicle is primarily designed for transporting people and luggage,
but it may also be used for towing a trailer.
We recommend use of the PEUGEOT genuine towbar with ball
which can be removed without tools and its harness that have
been tested and approved from the design stage of your vehicle,
and that the fi tting of the towbar is entrusted to a PEUGEOT
dealer or a qualifi ed workshop.
If the trailer is fi tted outside the PEUGEOT dealer network, it must
be fi tted in accordance with the manufacturer's instructions.
DRIVING ADVICE
Driving with a trailer subjects the towing vehicle to more signifi cant
stress and its driver must be particularly careful.
Distribution of loads
)
Distribute the load in the trailer so that the heaviest items are as
close as possible to the axle and the nose weight approaches the
maximum permitted without exceeding it.
Air density decreases with altitude, thus reducing engine performance.
Above 1 000 metres, the maximum towing load must be reduced by
10 % and so on for every 1 000 metres of altitude.
Refer to the "Technical data" section for details of the weights and
towing loads which apply to your vehicle version.
Side wind
)
Take into account the increased sensitivity to side wind.
