2012.5 Peugeot 508 Hybrid Dag bulb

.
.
Contents
Child seats 153
ISOFIX child seats 160
Child lock 164
Child safety
Direction indicators 165
Emergency or assistance call 166
Horn 166
Tyre under-infl ation detection 167
ESC system 168
Seat belts 171
Airbags 174
Safety
Te m p o r a ry puncture repair kit 178
Changing a wheel 184
Changing a bulb 191
Changing a fuse 200
12 V battery 204
Energy economy mode 207
Changing a wiper blade 208
To w i ng the vehicle 209
To w i ng a trailer 211
Fitting roof bars 213
Accessories 214
Practical information
Opening the bonnet 217
Running out of fuel (Diesel) 218
Petrol engines 219
Diesel engines 220
Checking levels 222
Checks 225
Checks
Petrol engines 227
Petrol weights 228
Diesel engines 230
Diesel weights 233
Dimensions 236
Identifi cation markings 237
Technical data
Emergency or assistance 239
JBL equipment 241
Peugeot Connect Navigation (RT6) 243
Audio system 297
Audio equipment and telematics
Alphabetical index
Visual search

144
Visibility






Manual adjustment
of halogen
headlamps







Automatic adjustment of xenon
headlamps
To avoid causing a nuisance to other road
users, the beams of the halogen headlamps should be adjusted according to the load in the
vehicle.1 Driver 2
Driver + front passenger.3
Driver + front passenger + rear passengers.4
5 people.5
5 people + a load in the boot. 6
Driver + a load in the boot. If a fault occurs
, this warning lamp is displayedin the instrument panel,
accompanied by an audible signal and a
message in the instrument panel screen.
The s
ystem then places your headlamps in the lowest position.
In order to avoid causing a nuisance to other road users, this system corrects the height of the
xenon headlamps beam automatically and when
stationary, in relation to the load in the vehicle.

If a fault occurs, do not touch the xenonbulbs. Contact a PEUGEOT dealer or a qualified workshop.


The initial setting is position "0".

8
191
Practical information











Changing a bulb


Front lamps
Model with xenon and directionalheadlamps
1.Daytime running lamps / sidelamps (light emitting diodes - LEDs).2.Directional dipped / main beam
headlamps (D1S-35W).3.Direction indicators (PY21-21W).4.Foglamps (directional according to
version) (H8).
Model with halogen headlamps
1.Dipped and main beam headlamps(H7-55W).2.Sidelamps (W5-5W).3.Main beam headlamps (H7-55W).4.Daytime running lamps (SP13-13W).5.Foglamps (directional according toversion) (H8).6. Direction indicators (PY21-21W).
For H7 type bulbs with lugs... take care toobserve their correct installation so as toensure the best lighting performance.
In some weather conditions (e.g. lowtemperature or humidity), the presenceof misting on the internal surface of the glass of the headlamps and rear lamps is normal; it disappears after the lampshave been on for a few minutes.

192
Practical information
Dipped beam headlamps(halogen model)
) Remove the protective plastic cover by pulling on the tab.)
Disconnect the bulb connector.)
Extract the bulb by pulling and change it.
For reassembly, carry out these operations in
reverse order.


The headlamps are fitted with
polycarbonate glass with a protectivecoating:)do not clean them using a dryor abrasive cloth, nor with adetergent or solvent product,)use a sponge and soapy water, )when using a high pressure washer on persistent marks, do not keepthe lance directed towards thelamps or their edges for too long,so as not to damage their protectivecoating and seals,)do not touch the bulb directly withyour fingers, use lint-free cloths.
Risk of electrocution
Xenon bulbs (D1S-35W) must bereplaced by a PEUGEOT dealer or aqualified workshop.
Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of seriousburns). It is imperative to use only anti-ultraviolet (UV) type bulbs in order notto damage the headlamp. Always replace a failed bulb with a new bulb with the same type andspecification.

8
193
Practical information
Sidelamps (halogen model)
)Remove the protective plastic cover bypulling on the tab.)Unclip the bulb holder. )Remove the bulb by pulling it out and change it.
For reassembly, carry out these operations in
reverse order.

Main beam headlamps (halogenmodel)
)
Remove the protective plastic cover by
pulling on the tab. ) Disconnect the bulb connector. )
Remove the bulb by pulling it out andchange it.
For reassembly, carry out these operations in reverse order.








Dipped and main beam
headlamps (xenon model)

D1S xenon bulbs must be changedby a PEUGEOT dealer or a qualifiedworkshop, as there is a risk of electrocution.
It is recommended that the D1S bulbsare changed at the same time when oneof them fails.
Daytime running lamps
(xenon model)

For the replacement of these light-emitting diode (LED) lamps, contacta PEUGEOT dealer or a qualifiedworkshop.

194
Practical information
lamps (halogen model)
)Turn the wheel fully inwards for easy access to the wheel arch liner. )Remove the two fixing screws for the access flap, located in the wheel arch. )Pull away the wheel arch liner.
)Turn the bulb holder a quarter of a turn and
pull it out.
)Disconnect the bulb holder connector. )Pull the bulb and change it.
For reassembly, carry out these operations in reverse order.
Yo u m ay also contact a PEUGEOT dealer
or a qualified workshop to have these bulbs replaced.

8
195
Practical information
Direction indicators
)Lie down under the vehicle. )Remove the screws securing theunderbody shield. )Remove the underbody shield.
) Turn the bulb holder a quar ter turn and pull
it out. ) Replace the faulty bulb.
For reassembly, carry out these operations in reverse order.
You can also contact a PEUGEOT dealer or aqualified workshop for the replacement of thesebulbs.
Integrated direction indicator
side repeaters
You should contact a PEUGEOT dealer or a qualified workshop for the replacement of these
bulbs.
Door mirror
s
potlamps
You should contact a PEUGEOT dealer or a qualified workshop for the replacement of the
light emitting diode - LED.

196
Practical information
1.Brake lamps (light emittingdiodes - LEDs).2. Reversing lamps (P21W).3.Direction indicators (PY21W amber).4.Sidelamps (light emitting diodes -LEDs).5.Foglamps (H21W).
Rear lamps (Saloon)
Reversing lamp, direction
indicator and foglamp bulbs
) Open the boot, then the plastic cover. )
Remove the two lamp unit fixing nuts. )
Extract the lamp unit carefully from the outside.)
Disconnect the electrical connector.
)Spread the six tabs and remove the bulb holder. )Turn the bulb a quar ter of a turn and pull it out.
For reassembly, carry out these operations in
reverse order.




Changing the light emittingdiode-LED lamps

For replacement, contact a PEUGEOT dealer or qualified workshop.