2012.5 Peugeot 308 SW BL lock
[x] Cancel search: lockPage 34 of 382
1
32
INSTRUMENTS and CONTROLS
Low fuel level
fi xed with the
needle in the
red zone,
accompanied
by an audible
signal and a
message.
When it fi rst comes on there
remains approximately 6 litres
of fuel in the tank.
At this point, you begin to
use the fuel reserve. Refuel as soon as possible to avoid running out
of fuel.
Until suffi cient fuel has been added, this warning
lamp will come on every time the ignition is
switched on, accompanied by an audible signal
and a message.
This audible signal and message are repeated
with increasing frequency as the fuel level drops
towards "0"
.
Fuel tank capacity: approximately 60 litres
.
Never continue to drive until you run out of fuel,
as this could damage the emission control and
injection systems.
Warning lamp
is on
Cause
Action / Observations
Anti-lock
Braking
System
(ABS)
fi xed. The anti-lock braking
system has a fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact
a PEUGEOT dealer or a qualifi ed workshop
without delay.
Dynamic
stability
control
(ESP/ASR)
fl ashing. The ESP/ASR regulation is
active. The system optimises traction and improves the
directional stability of the vehicle.
fi xed. Unless it has been
deactivated (button pressed
and its indicator lamp on) the
ESP/ASR system has a fault. Have it checked by a PEUGEOT dealer or a
qualifi ed workshop.
Directional
headlamps
fl ashing. The directional headlamps
system has a fault. Have it checked by a PEUGEOT dealer or a
qualifi
ed workshop.
Foot on the
brake pedal
fi xed. You have forgotten to press
the brake pedal when
starting the engine, with
an electronic gear control
gearbox. You have to press the brake pedal to start the
engine (gear lever in position N
).
Page 43 of 382
1
41
INSTRUMENTS and CONTROLS
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be registered.
Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:
)
switch off the ignition,
)
press and hold the ".../000"
button
on the right of the instrument panel,
)
switch on the ignition; the
distance recorder display begins a
countdown,
)
when the instrument panel central
screen indicates "=0"
, release the
button; the spanner disappears
from the screen. The distance remaining may be
weighted by the time factor, de-
pending on the driving conditions.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Service overdue
For 5 seconds after the ignition is
switched on, the spanner fl ashes
to
indicate that the service must be carried
out as soon as possible.
Example:
the service is overdue by 186 miles
(300 km).
For 5 seconds after the ignition is
switched on, the screen indicates:
5 seconds after the ignition is switched on,
the distance recorder resumes its normal
operation. The spanner remains on
.
Retrieving the service information
You can access the service information
at any time.
This information appears, depending
on version, when running through the
manual check procedure.
)
Briefl y press the ".../000"
button on
the right of the instrument panel.
The service information is
displayed for a few seconds on the
instrument panel central screen,
then disappears.
Page 45 of 382
1
43
INSTRUMENTS and CONTROLS
Distance recorders
The total and trip distances are dis-
played for thirty seconds when the ig-
nition is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
Total distance recorder
Trip distance recorder
)
With the ignition on, press and hold
this button until zeros appear.
Manual Check
This function allows you to check the status
of the vehicle (reminder of the active alert
warnings) and the service information.
)
With the engine running, to start
a manual check, briefl y press
the "CHECK/000"
button on the
instrument panel. If no faults have been detected,
"CHECK OK"
appears in the instru-
ment panel central screen.
If a "major" fault has been detected, only
the warning lamps concerned appear
in the instrument panel central screen.
Have it checked by a PEUGEOT dealer
or a qualifi ed workshop.
If a "minor" fault has been detected, the warn-
ing lamp concerned then "CHECK OK"
ap-
pear in the instrument panel central screen.
Contact a PEUGEOT or a qualifi ed work-
shop.
Measures a distance travelled since it
was reset to zero by the driver. Measures the total distance travelled by
the vehicle since its fi rst registration.
Page 76 of 382
3
74
COMFORT
REAR SEATS
Forwards-backwards
adjustment
Seat back angle adjustment
)
Pull one of the straps B
, located
at the front of the seat, then adjust
the angle to one of the 7 positions
offered.
)
Release the strap to lock the seat
back in this position.
Table position
)
Raise the bar A
and slide the seat
forwards or backwards.
)
Place the head restraint in the low
position.
)
Pull one of the straps B
, located at
the front of the seat.
)
Fold the seat back fully onto the
seat cushion; the seat automatically
moves back fully.
)
Press on the seat back to lock it.
Folding
Once the seat has been placed in the
table position, carry out the following
operations:
)
move back the seat fully using the
bar A
,
)
raise the lever C
, located at the rear
right of the seat, to release the rear
feet,
)
raise the seat fully so that it remains
in the fully folded
position.
You can also carry out these oper-
ations from the 3rd row using one
of the straps B
, located at the rear
of the seat. These operations allow access to
the 3
rd row, exit from the 3 rd
row and
folding of the seats from the boot. In the 2nd row, these three seats are
identical and can be adjusted for your
comfort. They can be placed in the table
position, folded or removed to obtain a
variety of loading confi gurations. During the forwards-backwards and
seat back angle adjustment opera-
tions, take care not to apply any
force to the load space cover roller.
Page 77 of 382
3
75
COMFORT
Removal
Installation
Once the seat has been folded, carry
out the following operations:
)
pull the red strap D
to release the
front feet of the seat,
)
lift the seat and carry it using the
carrying handle E
.
Never use the adjustment straps
to remove, install or carry a seat;
use the carrying handle E
provided
for this purpose (weight of the seat:
approximately 18 kg).
Once the seat has been removed,
in order to protect its electronic
systems, it must be stored in a
clean, dry location sheltered from
bad weather. Locked
Released
)
Tilt the folded seat rearwards; the
front and rear feet lock automati-
cally.
)
Pull one of the straps B
to release
the seat back, then raise it.
)
Check that no object is obstructing
the anchorages on the fl oor, so
preventing correct locking seat's
feet.
)
Carry the seat using the carrying
handle E
.
)
Put the front feet of the seat in place
in the corresponding anchorages.
)
Raise the lever C
to check that the
rear feet are released.
Page 79 of 382
3
77
COMFORT
Installation
)
First remove the anchorage covers
on the fl oor.
)
Carry the seat using the carrying
handle E
.
)
Put the seat's front feet in place in
the corresponding anchorages.
)
Raise the bar B
to check that the
rear feet are released.
)
Tilt the folded seat rearwards;
the front and rear feet lock
automatically.
)
Raise the seat back.
Page 82 of 382
3
80
COMFORT
The objects observed are, in real-
ity, closer than they appear.
Take this into account in order to
correctly judge the distance of ve-
hicles approaching from behind.
MIRRORS
Door mirrors
Each fi tted with an adjustable mirror
glass permitting the lateral rearward vi-
sion necessary for overtaking or parking.
They can also be folded for parking in
confi ned spaces.
Folding
)
From outside: lock the vehicle using
the remote control or the key.
)
From inside: with the ignition on, pull
the control A
in the central position
rearwards.
The folding and unfolding of the door
mirrors using the remote control
can be deactivated by a PEUGEOT
dealer or a qualifi ed workshop.
Never fold or unfold the electric
folding mirrors manually.
Adjustment
Unfolding
)
From outside: unlock the vehicle
using the remote control or the key.
)
From inside: with the ignition on, pull
the control A
in the central position
rearwards. If the mirrors are folded using con-
trol A
, they will not unfold when the
vehicle is unlocked. Pull again on
control A
.
)
Move control A
to the right or to
the left to select the corresponding
mirror.
)
Move control B
in all four directions
to adjust.
)
Return control A
to the central
position.
Demisting - Defrosting
If your vehicle is fi tted with heated
mirrors, the demisting-defrosting
operates by switching on the heat-
ed rear screen (refer to the "Rear
screen demist-defrost" page).
Page 84 of 382
3
82
COMFORT
STEERING WHEEL ADJUSTMENT
)
When stationary
, pull the control
lever to release the adjustment
mechanism.
)
Adjust the height and reach to suit
your driving position.
)
Push the control lever to lock the
adjustment mechanism.
As a safety precaution, these op-
erations should only be carried out
while the vehicle is stationary.
Automatic day/night model
In order to ensure optimum vis-
ibility during your manoeuvres, the
mirror lightens automatically when
reverse gear is engaged.
By means of a sensor, which measures
the light from the rear of the vehicle, this
system automatically and progressively
changes between the day and night
uses.
Adjustment
)
Adjust the mirror so that the glass is
directed correctly in the "day" position.
As a safety measure, the mirrors
should be adjusted to reduce the
"blind spot".
Manual day/night model
Day / night position
)
Pull the lever to change to the "night"
anti-dazzle position.
)
Push the lever to change to the
normal "day" position.
Rear view mirror
Adjustable mirror providing a central
rearward view.
Equipped with an anti-dazzle system,
which darkens the mirror glass: this re-
duces the nuisance to the driver caused
by the headlamps from following vehi-
cles, low sun...