)Lower the vehicle fully. )Fold the jack 2 and detach it. )
Tighten the security bolt using the
wheelbrace 1 fitted with the securitysocket 5. )
Tighten the other bolts using the
wheelbrace 1 only. )
Refit the bolt covers on each of the bolts or
the hub cap (depending on equipment). ) Store the tools in the box.
215
Practical information
Towing the vehicle
Procedure for having your vehicle towed or for towing another vehicle using a removable
tow
ing eye.
To w i ng your vehicle
To w i ng another vehicle
Access to the tools
The towing eye is installed in the boot under
the floor.
To gain access to it: )open the boot, )remove the towing eye, located in the tool box.
)
On the front bumper, unclip the cover by
pressing at the bottom to disengage thesecuring lugs. ) Screw the towing eye in fully. )
Install the towing bar. )
Switch on the hazard warning lamps on the
t
owed vehicle.
) On the rear bumper, unclip the cover bylevering at the left with the point of the
towing eye. ) Screw the towing eye in fully. )
Install the towing bar. )
Switch on the hazard warning lamps on the
t
owed vehicle.
When towing with all four wheels on theground, always use a towing bar.
When towing with only two wheels on the ground, always use professionallifting equipment.
When towing with the engine off, thereis no longer any braking or steeringassistance.
)Place the gear lever in neutral(position N
on the electronic gearbox system or automaticgearbox).Failure to obser ve this special condition could result in damageto certain braking components and the absence of braking assistancethe next time the engine is started.
Fitting roof bars
rack, for a loading height not exceeding40 cm (with the exception of bicycle carriers): 70kg.
If the height exceeds 40 cm, adapt the
speed of the vehicle to the profile of theroad to avoid damaging the roof bars and the fixings on the roof.
Be sure to refer to national legislation in order to comply with the regulations for transporting objects which are longer than the vehicle. When
fitting transverse roof bars, take care toposition them correctly: Use accessories recommended by CITROËN obser ving the manufacturer'srecommendations and fitting instructions so as to avoid the risk of damaging the body (deformation,scratches, ...).
)Remove the cap using an allenTM key. )Put the bars into position then fit and
tighten the securing screws.
219Practical information
Accessories
A wide range of accessories and genuine par ts is available from the CITROËN dealer network.
These accessories and par ts have been tested and approved for reliability and safety.
They are all adapted to your vehicle and benefit from CITROËN's recommendation and warranty.
"Comfort":
door deflectors, side window blinds, rear screen blind, isotherm module, coat hanger fixed to head restraint, mobile reading lamp, mirror for caravan, parking sensors...
"Transport systems":
child seats and booster cushions, boot carpet,
boot liner, boot net, boot spacers, transverse
roof bars, bic
ycle carrier, ski carrier, roof boxes,
towbars, wiring harnesses...
If a towbar and wiring harness are fitted
outside the CITROËN dealer network, theinstallation must be done using the vehicle's electrical pre-equipment and fitted following the manufacturer's recommendations.
"Styling":
gear lever knobs, aluminium foot rest, alloy wheels, chrome mirror shells, chrome door aperture finishers...
*
To avoid an
y risk of jamming the pedals:
- ensure that mats are correctly positionedand secured,
- never fit one mat on top of another.
"Security and safety":
anti-intrusion alarm, anti-tilt unit, stolen
vehicle tracking system, child seats and
booster cushions, breathalyser, first aid kit, fire
extinguisher, warning triangle, high visibility
vest, wheel security bolts, snow chains, non-
slip covers...
"Protection":
mats * , seat covers compatible with lateral
airbags, mud flaps, door protective mouldings,bumper protection strips, vehicle cover...
The rear bodywork has been designedto avoid spray.
