Page 46 of 356
System for manual adjustment of the brightness of the instruments and controls in relation to theexterior brightness.
Lighting dimmer
Activation
When the lighting is on:
)press the button to change the brightness
of the instruments and controls, )when the level of brightness required isreached, release the button.
Deactivation
When the lighting is off, or in day mode on
vehicles fitted with daytime running lamps,pressing the button does not have any effect.
System which measures the total distance
travelled by the vehicle during its life.
The total and trip distances are displayed for
thir ty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked.
Total distance recorder
System which measures a distance travelledduring a day or other period since it was reset
to zero by the driver. ) With the ignition on, press the button until
zeros appear.
Trip distance recorder
To c o nform to legislation in the countryyou are crossing, change the units of distance (miles or km) via the configuration menu.
Page 54 of 356
Electronic key
remote control
Unlocking the vehicle
Complete unlocking
Selective unlockin
g Unlocking the boot
System which permits central unlocking or
locking of the vehicle using the lock or from adistance. It is also used to locate and start thevehicle, as well as providing protection against
theft.
This settin
g is done in the configuration menu.
Complete unlocking is activated bydefault.
Unlocking is confirmed by rapid flashing of the direction indicators for around two seconds.
At the same time, depending onversion, the door mirrors unfold.
Locking the vehicle
Locking is confirmed by fixed lighting of the direction indicators for approximately two seconds.
The door mirrors fold at the same time.
)To u n l o c k o n ly the driver's door,press the open padlock once. )Press the closed padlock to lock
the vehicle completely. Hold the button down until the
windows close completely.
)
Press this button until you hear
th
e boot unlock. The vehicle is completely unlocked.
Be aware of children when operatingthe windows.
)
Press the open padlock to unlock
the vehicle.
) To unlock the other doors and the boot,
press the open padlock again.
Page 56 of 356
Locking the vehicle
)With the electronic key in the definedzone A , press with a finger on one of the
door handles (at the markings) to lock the
vehicle.
Maintain pressure with your finger until the
windows close completely.
Locking is confirmed by fixed lighting of the direction indicators for approximately two seconds.The door mirrors fold at the same time.
If one of the doors or the boot is still open or if the key for Keyless Entry and Starting has been left inside the vehicle,the central locking does not take place. When the vehicle is locked, if it isunlocked inadvertently, it will relockautomatically after about thir ty secondsunless a door is opened.
The folding and unfolding of the door mirrors by the remote control can bedeactivated by a CITROËN dealer or a qualified workshop.
As a safety measure (children onboard), never leave the vehicle without taking the key for the Keyless Entry andStarting system, even for a shor t period.Guard against theft when the key for the Keyless Entry and Starting systemis in the defined zone with the vehicle unlocked. After a long period of parking, theautomatic detection functions of the key are inhibited so as to not discharge thevehicle's battery. You should then use
the remote control function of the key to unlock the vehicle.
Ensure that no one prevents the correct operation of the windows.Be aware of children when operatingthe windows.This
function allows you to identify your vehicle from a distance, particularly in poor light. Your vehicle must be locked.
Locating your vehicle
)Press the closed padlock on the remotecontrol.
This will switch on the cour tesy lamps and thedirection indicators will flash for a few seconds.
Page 68 of 356
Cockpit glass roof
A tinted glass panoramic sur face to increase
the light and visibility in the passenger compartment. Fitted with three electric blinds to improve
tem
perature and noise related comfort. There are two options for openin
g and closing:
Electric blinds
)Pull or press control, going beyond the point of resistance.
One press opens or closes the blind
completely.
After a new action on the the control, the
blind continues moving for around 2 cm,
then stops.
) Pull or press the control without going
beyond the point of resistance (forwards to close and rear wards to open).
When you release the control, the blindcontinues moving for around 2 cm, thenstops.
Page 69 of 356
67
Access
Safety anti-pinch
If the blind stops and immediately opens again
during a closing manoeuvre: ) operate the control until the blind is fully
open,
) then operate the control until the blind isfully closed. The safety anti-pinch function is notoperational during these operations.
If the blind meets an obstacle during operation, you must reverse themovement of the blind. To do this, press the control concerned. When the driver operates the blind control, they must ensure that no one ispreventing correct closing of the blind.
The driver must ensure that passengersuse the blind correctly.
Be aware of children when operatingthe blind.
Reinitialisation
If power to the blind is cut off while it is moving,
the safety anti-pinch must be reinitialised: )operate the control until the blind is fullyclosed, )continue to press for at least 3 seconds. A slight movement of the blind will then be
noticeable, confirming the reinitialisation.
In automatic mode and at the end of its travel,
if the blind meets an obstacle while closin
g it stops and moves back slightly.
Page 83 of 356
81Comfort
These have one position for use (up) and a
stowed position (down).
They can also be removed.
To remove a head restraint: ) release the backrest using control 1 , )
tilt the backrest 2slightly forwards, )
pull the head restraint upwards to the stop, )
then, press the lug A.
Rear head restraints
Never drive with the head restraintsremoved; they must be in place and correctly adjusted.
)Remove the seat cushion 1
from its fixings by pulling upwards.
Removing the seat cushion
Refittin
g the seat cushion
)Position the seat cushion 1
ver tically in itsfixings.
Page 85 of 356
83Comfort
Automatic day/night model
By means of a sensor, which measures the
light from the rear of the vehicle, this system
automatically and progressively changes
between the da
y and night uses.
Adjustable mirror providing a central rearwardview.
Equipped with an anti-dazzle system, whichdarkens the mirror glass and reduces thenuisance to the driver caused by the sun, headlamps from other vehicles...
Rear view mirror
In order to ensure optimum visibility during your manoeuvres, the mirror lightens automatically when reverse gear is engaged.
Steering wheel adjustment
)When stationary, pull the control lever to yrelease the adjustment mechanism. )
Adjust the height and reach to suit your
driving position. ) Push the control lever to lock theadjustment mechanism.
As a safety precaution, these operations should only be carried out while the vehicle is stationary.
As a safety measure, the mirrors shouldbe adjusted to reduce the "blind spot".
Seeing clearly
For better rear vision, align the bottom of the rear view mirror with the bottom of the rear screen.
Page 87 of 356
85
Comfort
Mats Removable carpet protection.
)
move the seat fully back, )
fit the mat in place, )
engage the fixings by pressing down on
them.
Fitting
Removal
To remove the mat on the driver's side: )
move the seat fully back,
)
disengage the fixings, leaving the fixingpins in the floor carpet, )
remove the mat.
Refitting
To refit the mat on the driver's side: )
position the mat correctly, )
refit the fixings by pressing, )
check that the mat is secured correctly.
To avoid any risk of jamming of the pedals:
- only use mats which are suited tothe fixings already present in thevehicle; these fixings must be used,
- never fit one mat on top of another.
The use of mats not approved byCITROËN may inter fere with access tothe pedals and hinder the operation of the cruise control / speed limiter.
)To use the cigarette lighter, press it in and wait a few seconds until it pops outautomatically. )To connect a 12 V accessory (max power:
120 W), remove the cigarette lighter andconnect a suitable adaptor.
You can use this socket to connect a telephonecharger, a bottle warmer...
After use, put the cigarette lighter back intoplace straight away.
Cigarette lighter /
12 V accessory
socket
