INSTRUMENT AND CONTROL FUNCTIONS
3-9
3
EAU47617
Multi-function meter unit
WARNING
EWA12422
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changingsettings while riding can distract the
operator and increase the risk of an
accident.
The multi-function meter unit is
equipped with the following:
a speedometer
a tachometer
an odometer
two tripmeters (which show the
distance traveled since they were
last set to zero)
a fuel reserve tripmeter (which
shows the distance traveled since
the fuel level warning light came
on)
a stopwatch
a clock
a coolant temperature display
an air intake temperature display
a transmission gear display
a drive mode display (which shows
the selected drive mode)
a throttle opening position display
a fuel consumption display (instan-
taneous and average consumption
functions)
a self-diagnosis device
a display brightness, shift timing
indicator light and throttle opening
position display control mode
TIP
Be sure to turn the key to “ON” be-
fore using the “SELECT” and “RE-
SET” buttons.
For the U.K. only: To switch the
speedometer and odometer/trip-
meter/fuel consumption displays
between kilometers and miles,
press the “SELECT” button for at
least one second.
Tachometer
1.“RESET” button
2.“SELECT” button
3. Tachometer
4. Shift timing indicator light
5. Throttle opening position display
6. Coolant temperature display/air intake tem-
perature display
7. Drive mode display
8. Speedometer
9. Odometer/tripmeter/fuel reserve tripmeter/in-
stantaneous fuel consumption/average fuel
consumption
10.Clock/stopwatch
11.Transmission gear display2
134
5
6
7
8
9
10 11
1. Tachometer
2. Tachometer red zone
2 1
U14BE2E0.book Page 9 Friday, June 18, 2010 8:47 AM
INSTRUMENT AND CONTROL FUNCTIONS
3-10
3 The electric tachometer allows the rider
to monitor the engine speed and keep it
within the ideal power range.
When the key is turned to “ON”, the ta-
chometer needle sweeps once across
the r/min range and then returns to zero
r/min in order to test the electrical cir-
cuit.
NOTICE
ECA10031
Do not operate the engine in the ta-
chometer red zone.
Red zone: 13750 r/min and aboveClock and stopwatch modesTo set the clock
1. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
2. When the hour digits start flashing,
push the “RESET” button to set the
hours.
3. Push the “SELECT” button, and
the minute digits start flashing.
4. Push the “RESET” button to set
the minutes.
5. Push the “SELECT” button and
then release it to start the clock.
To display the stopwatchTo change the display to the stopwatch
mode, push the “SELECT” button and
“RESET” button together. To change
the display back to the clock mode,
push the “SELECT” button and “RE-
SET” button together; however, this is
not possible when the stopwatch is
counting.
Standard measurement1. Push the “RESET” button to start
the stopwatch.
2. Push the “SELECT” button to stop
the stopwatch.3. Push the “SELECT” button again
to reset the stopwatch.
Split time measurement
1. Push the “RESET” button to start
the stopwatch.
2. Push the start switch“” or “RE-
SET” button to measure split
times. Split times are displayed on
the odometer display for five sec-
onds.
3. Push the start switch“” or “RE-
SET” button to display the final
split time or push the “SELECT”
button to stop the stopwatch and
display the total elapsed time.
1. Clock/stopwatch
1
U14BE2E0.book Page 10 Friday, June 18, 2010 8:47 AM
