2011 YAMAHA YZ450F engine coolant

7-11
FUEL INJECTION SYSTEM
SENSOR OPERATION TABLE
Diagnos-
tic code
No.ItemActuation or
displayChecking methodActuation or LCD standard display
values
D01 Throttle angle DisplayDisplays the throttle angle. 0–125°
Check with throttle fully closed. When throttle is fully closed:15–19°
Check with throttle fully open. When throttle is fully
opened:95–101 °
D02 Atmosphere DisplayDisplays the atmospheric pres-
sure.
• Measure the atmospheric pres-
sure.0–126 kPa
Displays the atmospheric pressure
according to the elevation and
weather.
Example
0 m above sea level: Approx: 101
kPa
3000 m above sea level:Approx: 70
kPa
D03 Intake air pressure DisplayDisplays the intake air pressure.
• Check the intake manifold pres-
sure.
• Check that the intake air pres-
sure changes while the engine is
being cranked.0–126 kPa
While the engine is stopped: Dis-
plays the atmospheric pressure ac-
cording to the elevation and
weather.
Example
0 m above sea level: Approx: 101
kPa
3000 m above sea level:Approx: 70
kPa
While the engine is being cranked:
Displays the intake air pressure.
D05 Intake air temperature DisplayDisplays the intake air tempera-
ture.
• Check the temperature in the in-
take manifold.-20–100°C
Cold engine: Displayed tempera-
ture is close to the ambient temper-
ature.
Warm engine: Displayed tempera-
ture is approximately 20 °C higher
than the ambient temperature.
D06 Coolant temperature DisplayDisplays the coolant temperature.
• Check the coolant temperature.-20–150°C
Cold engine: Displayed tempera-
ture is close to the ambient temper-
ature.
Warm engine: Displayed tempera-
ture is the current coolant tempera-
ture.
D08 Lean angle sensor DisplayDisplays the lean angle sensor
output voltage.
Remove the ECU and incline it 45°
or more.0–5.0 V
1.0 V: Upright
4.0 V: Overturned
D30 Ignition coil ActuationCheck that power is supplied to
the ignition coil.
• Check that a spark is generated.
• Illuminates the engine trouble
warning light.Actuates the ignition coil for five
times every second.
The "WARNING" LED on the FI di-
agnostic tool comes on each time
the fuel injector is actuated.

7-20
FUEL INJECTION SYSTEM
Make sure that the engine is completely cool before checking the coolant temperature sensor.
Fault code No. 21
Symptom Coolant temperature sensor signal is not received properly.
Fail-safe system Able to start
Able to drive
Diagnostic code No. D06
FI diagnostic tool display -20–150°C
Cold engine: Displayed temperature is close to the ambient temperature.
Warm engine: Displayed temperature is the current coolant temperature.
Checking method Check the coolant temperature.
Item Item/components and probable cause Check or maintenance job Checking method
1 Check the connection and locking condition of
the coolant temperature sensor coupler.
Disconnect the coupler and check the pins
(bent or broken terminals and locking condition
of the pins).Poor connection → Properly con-
nect, repair, or replace.Set the switch on the FI di-
agnostic tool sub-wire har-
ness to "ON", and then
check the fault code dis-
play.
Fault code number is not
displayed → Service is
finished.
Fault code number is dis-
played → Refer to item 2.
2 Check the connection and locking condition of
the wire harness ECU coupler.
Disconnect the coupler and check the pins.
(bent or broken terminals and locking condition
of the pins)Poor connection → Properly con-
nect, repair, or replace.Set the switch on the FI di-
agnostic tool sub-wire har-
ness to "ON", and then
check the fault code dis-
play.
Fault code number is not
displayed → Service is
finished.
Fault code number is dis-
played → Refer to item 3.
3 Continuity of harness Open or short circuit → Replace.
Between coolant temperature sen-
sor coupler and ECU coupler
(Brown–Brown)
(Black/Blue–Black/Blue)Set the switch on the FI di-
agnostic tool sub-wire har-
ness to "ON", and then
check the fault code dis-
play.
Fault code number is not
displayed → Service is
finished.
Fault code number is dis-
played → Refer to item 4.
4 Installed condition of sensor. Check that the sensor is installed
securely and that there are no
pinched leads.Check that the ECU
is installed securely and that there
are no pinched leads.
Incorrect installation → Reinstall
or repair.Set the switch on the FI di-
agnostic tool sub-wire har-
ness to "ON", and then
check the fault code dis-
play.
Fault code number is not
displayed → Service is
finished.
Fault code number is dis-
played → Refer to item 5.

7-21
FUEL INJECTION SYSTEM
Make sure that the engine is completely cool before checking the intake air temperature sensor.
5 Defective coolant temperature sensor. Execute the diagnostic mode (di-
agnostic code No. D06).
Cold engine: Displayed temper-
ature is close to the ambient
temperature.
Displayed value is incorrect → Re-
place. Set the switch on the FI di-
agnostic tool sub-wire har-
ness to "ON", and then
check the fault code dis-
play.
Fault code number is not
displayed → Service is
finished.
Fault code number is dis-
played → Refer to item 6.
6 Malfunction in ECU. Replace the ECU.
Fault code No. 22
Symptom Intake air temperature sensor signal is not received properly.
Fail-safe system Able to start Able to drive
Diagnostic code No. D05
FI diagnostic tool display -20–100°C Cold engine: Displayed temperature is close to the ambient temperature.
Warm engine: Displayed temperature is approx imately 20°C higher than the ambient tem-
perature.
Checking method Check the temperature in the intake manifold. Item Item/components and probable cause Check or maintenance job Checking method
1 Check the connection and locking condition of the intake air temperature sensor coupler.
Disconnect the coupler and check the pins.
(bent or broken terminals and locking condition
of the pins) Poor connection
→ Properly con-
nect, repair, or replace. Set the switch on the FI di-
agnostic tool sub-wire har-
ness to "ON", and then
check the fault code dis-
play.
Fault code number is not
displayed → Service is
finished.
Fault code number is dis-
played → Refer to item 2.
Fault code No. 21
Symptom Coolant temperature sensor signal is not received properly.
Fail-safe system Able to start
Able to drive
Diagnostic code No. D06
FI diagnostic tool display -20–150°C Cold engine: Displayed temperature is close to the ambient temperature.
Warm engine: Displayed temperature is the current coolant temperature.
Checking method Check the coolant temperature. Item Item/components and probable cause Check or maintenance job Checking method