2011 YAMAHA YFM350R-W turn signal

Checking and lubricating the brake and
shift pedals ............................................. 8-32
Checking the wheel bearings ................... 8-32
Lubricating the swingarm pivots ............... 8-32
Lubricating the rear suspension relay arm
and connecting arm pivoting points ........ 8-33
Lubricating the upper and lower arm
pivots ...................................................... 8-34
Lubricating the steering shaft ................... 8-35
Battery ...................................................... 8-35
Replacing a fuse ...................................... 8-37
Headlight bulb .......................................... 8-38
Headlight beam ........................................ 8-38
Replacing the tail/brake light bulb ............ 8-38
Replacing a turn signal light bulb ............. 8-38
Replacing the license plate light bulb ....... 8-39
Auxiliary light bulb .................................... 8-40
Removing a wheel .................................... 8-40
Installing a wheel ...................................... 8-41
Troubleshooting ....................................... 8-42
Troubleshooting chart .............................. 8-43
CLEANING AND STORAGE .......................... 9-1
Cleaning ..................................................... 9-1
Storage ....................................................... 9-2SPECIFICATIONS .......................................10-1
CONSUMER INFORMATION.......................11-1
Identification numbers ...............................11-1
U10P60E0.book Page 3 Thursday, June 15, 2006 4:19 PM

4-2
4
EBU17791Indicator lights EBU27970Turn signal indicator light “”
This indicator light flashes when the turn signal
switch is pushed to the left or right.EBU17830Reverse indicator light “”
This indicator light comes on when the transmis-
sion is in the reverse position.
EBU17860Neutral indicator light “”
This indicator light comes on when the transmis-
sion is in the neutral position.EBU27980High beam indicator light “”
This indicator light comes on when the high beam
of the headlight is switched on.EBU28050Speedometer The speedometer shows the riding speed. This
speedometer is equipped with an odometer. The
odometer shows the total distance traveled.
1. High beam indicator light “”
2. Turn signal indicator light “”
3. Reverse indicator light “R”
4. Neutral indicator light “N”
1. Speedometer
2. Odometer
U10P60E0.book Page 2 Thursday, June 15, 2006 4:19 PM

4-3
4
EBU18061Handlebar switches
EBU18080Engine stop switch “/”
Set this switch to “” before starting the engine.
The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to “”.EBU18100Start switch “”
Push this switch to crank the engine with the start-
er.
1. Light switch “//”
2. Hazard switch “”
3. Turn signal switch “/”
4. Horn switch “”
5. Start switch “”
1. Engine stop switch “/”
U10P60E0.book Page 3 Thursday, June 15, 2006 4:19 PM

4-4
4
CAUTION:ECB00050See the starting instructions on page 6-1 priorto starting the engine.EBU28061Light switch “//”
Set the switch to “” to turn on the high beam.
Set this switch to “” to turn on the low beam.
Set the switch to “” to turn off the headlight.CAUTION:ECB00030Do not use the headlight with the engine turned
off for an extended period of time, otherwise
the battery may discharge to the point that the
starter motor will not operate properly. If this
should happen, remove the battery and re-charge it.EBU27990Turn signal switch “/”
To signal a right-hand turn, push this switch to
“”. To signal a left-hand turn, push this switch to
“”. When released, the switch returns to the cen-
ter position. To cancel the turn signal lights, push
the switch in after it has returned to the center po-
sition.
EBU18170Horn switch “”
Press the switch to sound the horn.EBU28000Hazard switch “”
With the key in the “ON” position, turn this switch to
“” to turn on the hazard lights (simultaneous
flashing of all turn signal lights).
The hazard lights are used in case of an emergen-
cy or to warn other drivers when your vehicle is
stopped where it might be a traffic hazard.CAUTION:ECB00860Do not use the hazard lights for an extended
length of time with the engine not running, oth-erwise the battery may discharge.EBU18280Throttle lever Once the engine is running, movement of the throt-
tle lever will increase the engine speed.
Regulate the speed of the ATV by varying the
throttle position. Because the throttle is spring-
loaded, the ATV will decelerate, and the engine will
return to an idle any time the hand is removed from
the throttle lever.
U10P60E0.book Page 4 Thursday, June 15, 2006 4:19 PM

7-24
7BRAKES AND ELECTRICAL EQUIPMENT
(turn signals, horn, headlight, etc.) FOR PROP-
ER OPERATION when you come out of the wa-
ter. Do not continue to ride your ATV until you
have regained adequate braking ability. (See
page 7-19.)
U10P60E0.book Page 24 Thursday, June 15, 2006 4:19 PM

8-37
8 access to a constant-voltage battery charg-
er, have a Yamaha dealer charge your bat-
tery.EBU28151Replacing a fuse The main fuse and signaling system fuse are locat-
ed under the seat. (See page 4-14.)
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off all electrical
circuits.
CAUTION:ECB00640To prevent accidental short-circuiting, turn off
the main switch when checking or replacing afuse.
2. Remove the blown fuse, and then install a
new fuse of the specified amperage.
WARNING
EWB02171Always use a fuse of the specified rating, and
never use a substitute object in place of the
proper fuse. An improper fuse or a substitute
object can cause damage to the electrical sys-tem, which could lead to a fire.
3. Turn the key to “ON” and turn on the electrical
circuits to check if the devices operate.
4. If the fuse immediately blows again, have a
Yamaha dealer check the electrical system.
1. Main fuse
2. Spare main fuse
3. Signaling system fuse
Specified fuses:
Main fuse:
15.0 A
Signaling system fuse:
7.5 A
U10P60E0.book Page 37 Thursday, June 15, 2006 4:19 PM

8-38
8
EBU28160Headlight bulb If the headlight bulb burns out, have a Yamaha
dealer replace it.EBU28170Headlight beam If a headlight beam adjustment is necessary, have
a Yamaha dealer perform it.EBU25600Replacing the tail/brake light bulb If the tail/brake light bulb burns out, replace it as
follows.
1. Remove the lens by removing the screws.2. Remove the defective bulb by pushing it in
and turning it counterclockwise.
3. Insert a new bulb into the socket, push it in,
and then turn it clockwise until it stops.
4. Install the lens by installing the screws.
CAUTION:ECB00700Do not overtighten the screws, otherwise thelens may break.EBU28030Replacing a turn signal light bulb 1. Remove the turn signal light lens by removing
the screw.
1. Screw
1. Tail/brake light bulb
U10P60E0.book Page 38 Thursday, June 15, 2006 4:19 PM

10-4
10
Front suspension:Type:
Double wishbone
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
200 mm (7.9 in)Rear suspension:Type:
Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
210 mm (8.3 in)Electrical system:Ignition system:
DC. CDI
Charging system:
AC magnetoBattery:Model:
YTZ10S
Voltage, capacity:
12 V, 8.6 AhHeadlight:Bulb type:
Halogen bulbBulb voltage, wattage x quantity:Headlight:
12 V, 35.0/35.0 W × 1Tail/brake light:
12 V, 5.0/21.0 W × 1
Front turn signal light:
12 V, 10.0 W
Rear turn signal light:
12 V, 10.0 W
Auxiliary light:
12 V, 5.0 W
License plate light:
12 V, 5.0 W
Neutral indicator light:
12 V, 1.7 W × 1
High beam indicator light:
LED
Turn signal indicator light:
LED
Reverse indicator light:
12 V, 1.7 W × 1
Fuses:Main fuse:
15.0 A
Signaling system fuse:
7.5 A
U10P60E0.book Page 4 Thursday, June 15, 2006 4:19 PM