2011 YAMAHA XT660Z torque

PERIODIC MAINTENANCE AND ADJUSTMENT
6-1
6
EAU17243
Periodic inspection, adjustment, and
lubrication will keep your vehicle in
the safest and most efficient condi-
tion possible. Safety is an obligation
of the vehicle owner/operator. The
most important points of vehicle ins-
pection, adjustment, and lubrication
are explained on the following pages.
The intervals given in the periodic
maintenance charts should be simply
considered as a general guide under
normal riding conditions. However,
depending on the weather, terrain,
geographical location, and individual
use, the maintenance intervals may
need to be shortened.
EWA10321
Failure to properly maintain the
vehicle or performing maintenance
activities incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle
service, have a Yamaha dealer per-
form service.
EWA15121
Turn off the engine when perfor-
ming maintenance unless otherwi-
se specified.
A running engine has moving
parts that can catch on body
parts or clothing and electrical
parts that can cause shocks or
fires.
Running the engine while servi-
cing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning – possibly leading to
death. See page 1-1 for more
information about carbon
monoxide.
EWA15460
Brake discs, calipers, drums, and
linings can become very hot during
use. To avoid possible burns, let
brake components cool before tou-
ching them.
EAU17381
Owner’s tool kit
1. Owner’s tool kit
The owner’s tool kit is located under
the seat. (See page 3-16).
The service information included in
this manual and the tools provided in
the owner’s tool kit are intended to
assist you in the performance of pre-
ventive maintenance and minor
repairs. However, additional tools
such as a torque wrench may be
necessary to perform certain mainte-
nance work correctly.
WARNING
WARNING
WARNING
56P-F8199-E0 30/6/10 09:24 Página 47

2. Remove the spark plug as
shown, with the spark plug
wrench included in the owner’s
tool kit.
To check the spark plug
1. Check that the porcelain insula-
tor around the center electrode of
the spark plug is a medium-to-
light tan (the ideal color when the
vehicle is ridden normally).
TIP
If the spark plug shows a distinctly
different color, the engine could be
operating improperly. Do not attempt
to diagnose such problems yourself.
Instead, have a Yamaha dealer check
the vehicle.
2. Check the spark plug for electro-
de erosion and excessive carbon
or other deposits, and replace it if
necessary.3. Measure the spark plug gap with
a wire thickness gauge and, if
necessary, adjust the gap to spe-
cification.
1. Spark plug gap
To install the spark plug
1. Clean the surface of the spark
plug gasket and its mating surfa-
ce, and then wipe off any grime
from the spark plug threads.
2. Install the spark plug with the
spark plug wrench, and then
tighten it to the specified torque.
TIP
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is
1/4–1/2 turn past finger tight. Howe-
ver, the spark plug should be tighte-
ned to the specified torque as soon
as possible.
3. Install the spark plug cap.
Tightening torque:
Spark plug:
12.5 Nm (1.25 m·kgf, 9.0 ft·lbf)
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
1
ZAUM0037
Specified spark plug:
NGK/CR7E
PERIODIC MAINTENANCE AND ADJUSTMENT
6-10
6
56P-F8199-E0 30/6/10 09:24 Página 56

3. Place an oil pan under the engine
to collect the used oil.
4. Remove the engine oil filler cap
and the drain bolt to drain the oil
from the crankcase.
1. Engine oil drain bolt (crankcase)
5. Remove the drain bolt to drain
the oil from the oil tank.
1. Engine oil drain bolt (oil tank)
6. Remove the oil filter element
drain bolt to drain the oil from the
oil filter element.
TIP
Skip steps 7–9 if the oil filter element
is not being replaced.
7. Remove the oil filter element
cover by removing the bolts.
1. Oil filter element drain bolt
2. Oil filter element cover bolt
8. Remove and replace the oil filter
element and O-rings.
TIP
Make sure that the O-rings are pro-
perly seated.
1. Oil filter element
2. O-ring
9. Install the oil filter element cover
by installing the bolts.
10. Install the oil filter element drain
bolt.
11. Tighten the oil filter element
cover bolts and the oil filter ele-
ment drain bolt to their specified
torques.
12. Install the engine oil drain bolts,
and then tighten them to their
specified torques.
Tightening torques:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil filter element drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-12
6
56P-F8199-E0 30/6/10 09:24 Página 58

13. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil
filler cap.
ECAM1061
The engine oil tank must be filled in
2 steps. First, fill the engine oil tank
with 1.90 L (2.0 US qt, 1.67 Imp.qt)
of the recommended engine oil.
Then, start the engine, race it 5 or 6
times, turn it off, and then add the
remainder of the engine oil.
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust
system have cooled down.
ECA11620
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a hig-
her quality than specified. In
addition, do not use oils labe-
led “ENERGY CONSERVING II”
or higher.
Make sure that no foreign
material enters the crankcase.
14. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the cau-
se.
15. Turn the engine off, and then
check the oil level and correct it if
necessary.16. Install the engine guard by insta-
lling the screws.
NOTICE
Recommended engine oil:
See page 8-1
Without oil filter element
replacement:
2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter element
replacement:
2.60 L (2.75 US qt, 2.29 Imp.qt
NOTICE
Tightening torques:
Engine oil drain bolt (crankcase):
30 Nm (3.0 m·kgf, 22 ft·lbf)
Engine oil drain bolt (oil tank):
18 Nm (1.8 m·kgf, 12.9 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-13
6
56P-F8199-E0 30/6/10 09:24 Página 59

TIP
Using the alignment marks on each
side of the swingarm, make sure that
both drive chain pullers are in the
same position for proper wheel align-
ment.
3. Tighten the axle nut, then the
locknuts to their specified tor-
ques.
EAU23025
Cleaning and lubricating the
drive chain
The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly
wear out, especially when riding in
dusty or wet areas. Service the drive
chain as follows.
ECA10583
The drive chain must be lubricated
after washing the motorcycle,
riding in the rain or riding in wet
areas.
1. Clean the drive chain with kero-
sene and a small soft brush.
NOTICE: To prevent damaging
the O-rings, do not clean the
drive chain with steam clea-
ners, high-pressure washers or
inappropriate solvents.
[ECA11121]
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant. NOTICE: Do not use
engine oil or any other lubri-cants for the drive chain, as
they may contain substances
that could damage the O-rings.
[ECA11111]
NOTICETightening torques:
Axle nut:
16 Nm (1.6 m·kgf, 11 ft·lbf)
Locknut:
105 Nm (10.5 m·kgf, 75 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-24
6
56P-F8199-E0 30/6/10 09:24 Página 70

EAU44790
Front wheelEWA14840
For the ABS model, have a Yamaha
dealer remove and install the whe-
el.
EAUB1441
To remove the front wheelEWA10821
To avoid injury, securely support
the vehicle so there is no danger of
it falling over.
1. Loosen the front wheel axle pinch
bolts, the wheel axle and the bra-
ke caliper bolts.
1. Wheel axle
2. Brake caliper bolt
3. Front wheel axle pinch bolt
4. Front wheel axle pinch bolt
2. Lift the front wheel off the ground
according to the procedure on
page 6-35.
3. Remove the brake caliper on
each side by removing the bolts.
NOTICE: Do not apply the bra-
ke after the brake calipers have
been removed, otherwise the
brake pads will be forced shut.
[ECA11051]
4. Pull the wheel axle out, and then
remove the wheel.
EAUB1472
To install the front wheel
1. Lift the wheel up between the
fork legs.
2. Insert the wheel axle.
3. Install the brake calipers by insta-
lling the bolts.
TIP
Make sure that there is enough space
between the brake pads before insta-
lling the brake calipers onto the brake
discs.
4. Lower the front wheel so that it is
on the ground.
5. Tighten the wheel axle and the
brake caliper bolts to the speci-
fied torques.
ECAB0061
Be sure the right brake disc is posi-
tioned exactly between the brake
pads to prevent any brake drag.
Tap the side of the right fork leg to
position the disc correctly.
6. Tighten wheel axle pinch bolt A,
and then pinch bolt B to their
specified torque.
NOTICE
WARNING
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-36
6
56P-F8199-E0 30/6/10 09:24 Página 82

7. Retighten pinch bolt A to the spe-
cified torque.
8. Apply the brake lever several
times, and then while holding the
brake lever in, push down hard
on the handlebar several times to
check for proper fork operation.EAU44800
Rear wheelEWA14840
For the ABS model, have a Yamaha
dealer remove and install the wheel.
EAU25314
To remove the rear wheelEWA10821
To avoid injury, securely support
the vehicle so there is no danger of
it falling over.
1. Loosen the axle nut.
1. Wheel axle nut
2. Drive chain slack adjusting bolt
3. Locknut
4. Drive chain
2. Lift the rear wheel off the ground
according to the procedure on
page 6-35.
3. Remove the axle nut.
1. Wheel axle
2. Drive chain slack adjusting bolt
3. Locknut
4. Brake caliper
4. Fully loosen the locknut on each
side of the swingarm.
5. Turn the drive chain slack adjus-
ting bolts fully in direction (a) and
push the wheel forward.
6. Remove the drive chain from the
rear sprocket.
TIP
If the drive chain is difficult to
remove, remove the wheel axle
WARNING
WARNING
Tightening torques:
Wheel axle:
60 Nm (6.0 m·kgf, 44 ft·lbf)
Front wheel axle pinch bolt:
18 Nm (1.8 m·kgf, 13 ft·lbf)
Brake caliper bolt:
40 Nm (4.0 m·kgf, 29 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-37
6
56P-F8199-E0 30/6/10 09:24 Página 83

first, and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.
The drive chain cannot be disas-
sembled.
7. While supporting the brake cali-
per bracket, pull the wheel axle
out, and then remove the wheel.
NOTICE: Do not apply the bra-
ke after the wheel has been
removed together with the bra-
ke disc, otherwise the brake
pads will be forced shut.
[ECA11071]
EAUB1450
To install the rear wheel
1. Install the wheel and the brake
caliper bracket by inserting the
wheel axle from the left-hand
side.
TIP
Make sure that the slot in the bra-
ke caliper bracket is fit over the
retainer on the swingarm.
Make sure that there is enough
space between the brake pads
before installing the wheel.
2. Install the drive chain onto the
rear sprocket.
3. Install the axle nut, and then
lower the rear wheel so that it is
on the ground.
4. Adjust the drive chain slack. (See
page 6-23).
5. Apply the rear brake several
times, and then tighten the axle
nut to the specified torque.EAU25871
Troubleshooting
Although Yamaha motorcycles recei-
ve a thorough inspection before ship-
ment from the factory, trouble may
occur during operation. Any problem
in the fuel, compression, or ignition
systems, for example, can cause poor
starting and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your motorcy-
cle require any repair, take it to a
Yamaha dealer, whose skilled techni-
cians have the necessary tools, expe-
rience, and know-how to service the
motorcycle properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
EWA15141
When checking the fuel system, do
not smoke, and make sure there
are no open flames or sparks in the
WARNING
Tightening torque:
Axle nut:
105 Nm (10.5 m·kgf, 75 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-38
6
56P-F8199-E0 30/6/10 09:24 Página 84