2011 YAMAHA VMAX lock

PERIODIC MAINTENANCE AND ADJUSTMENT
6-25
6
EAU46540
Checking the brake fluid level Front brake
Rear brake
Insufficient brake fluid may allow air to
enter the brake system, possibly caus-
ing it to become ineffective.Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads
and/or brake system leakage. If the
brake fluid level is low, be sure to check
the brake pads for wear and the brake
system for leakage.
TIPThe rear brake fluid reservoir is located
under the passenger seat. (See page
3-25.)Observe these precautions:

When checking the fluid level,
make sure that the top of the brake
fluid reservoir is level.


Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking perfor-
mance.


Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performance.


Be careful that water or dust does
not enter the brake fluid reservoir
when refilling. Water will signifi-
cantly lower the boiling point of the
fluid and may result in vapor lock,
and dirt may clog the ABS hydrau-
lic unit valves.


Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.


As the brake pads wear, it is nor-
mal for the brake fluid level to grad-
ually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.
1. Minimum level mark
1. Minimum level mark
1
1
Recommended brake fluid:
DOT 4
U2S3E2E0.book Page 25 Tuesday, September 21, 2010 10:43 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-33
6
EAU46453
Replacing the fuses The main fuse and the ABS motor fuse
are located behind cowling A. (See
page 6-8.) Fuse box 1 is located under
the rider seat. (See page 3-25.)Fuse box 1
Fuse box 2 is located behind panel B.
(See page 6-8.)Fuse box 2
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
the electrical circuit in question.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to1. Main fuse
2. ABS motor fuse
3. ABS motor spare fuse
1
3
2
1. ABS solenoid fuse
2. Fuel injection system fuse
3. Spare fuse
123
1. Ignition fuse
2. ABS control unit fuse
3. Headlight fuse
4. Backup fuse (for clock and immobilizer sys-
tem)
5. Electronic throttle valve fuse
6. Radiator fan fuse
7. Spare fuse
8. Signaling system fuse
9. Parking lighting fuse
10.Sub radiator fan fuse
1
2
3
4
5
6
7
8 107
9
U2S3E2E0.book Page 33 Tuesday, September 21, 2010 10:43 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-36
6
EAU24181
Tail/brake light This model is equipped with an LED-
type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.
EAU24204
Replacing a turn signal light
bulb 1. Remove the turn signal light lens
by removing the screw.
2. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break.
[ECA11191]
1. Screw
2. Turn signal light lens
1
2
1. Turn signal light bulb
1
U2S3E2E0.book Page 36 Tuesday, September 21, 2010 10:43 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-37
6
EAU50450
Replacing a license plate light
bulb 1. Remove the holding plate by re-
moving the bolts.
2. Remove the license plate light unit
bolts.3. Pull the license plate light unit out-
ward as shown to access the bulb
and its socket.
4. Remove the license plate light
socket (together with the bulb) by
turning it counterclockwise, and
then pulling it out.5. Remove the burnt-out bulb by pull-
ing it out.
6. Insert a new bulb into the socket.
7. Install the socket (together with the
bulb) by pushing it in, and then
turning it clockwise until it stops.1. Holding plate
2. Bolt
12
1. License plate light unit bolt
2. License plate light unit
1 2
1. License plate light bulb socket
2. License plate light unit
1. License plate light bulb
121
U2S3E2E0.book Page 37 Tuesday, September 21, 2010 10:43 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-38
68. Place the license plate light unit in
the original position, and then in-
stall the bolts.
9. Install the holding plate by install-
ing the bolts.
EAU46403
Replacing the auxiliary light
bulb If the auxiliary light bulb burns out, re-
place it as follows.
1. Remove the headlight unit. (See
page 6-34.)
2. Remove the auxiliary light socket
(together with the bulb) by turning
it counterclockwise.
3. Remove the burnt-out bulb by pull-
ing it out of the socket.4. Insert a new bulb into the socket.
5. Install the auxiliary light socket (to-
gether with the bulb) by turning it
clockwise.
6. Install the headlight unit.1. Auxiliary light bulb socket
1
1. Auxiliary light bulb
1
U2S3E2E0.book Page 38 Tuesday, September 21, 2010 10:43 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-42
6Engine overheating
WARNING
EWAT1040


Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.


Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the de-
tent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the cap
while turning it counterclockwise, and then remove the cap.
TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U2S3E2E0.book Page 42 Tuesday, September 21, 2010 10:43 AM

INDEXAABS ....................................................... 3-20
ABS warning light.................................... 3-6
Air filter element .................................... 6-19
Anti-theft alarm (optional)...................... 3-17
Auxiliary light bulb, replacing ................ 6-38BBattery................................................... 6-30
Brake and clutch fluids, changing ......... 6-26
Brake and clutch levers,
checking and lubricating ..................... 6-27
Brake and shift pedals,
checking and lubricating ..................... 6-27
Brake fluid level, checking .................... 6-25
Brake lever ............................................ 3-19
Brake lever free play, checking ............. 6-23
Brake light switches .............................. 6-24
Brake pedal ........................................... 3-20CCables, checking and lubricating .......... 6-26
Care ........................................................ 7-1
Catalytic converters .............................. 3-24
Clutch lever .................................. 3-18, 6-23
Coolant.................................................. 6-16
Coolant temperature warning light .......... 3-5
Cowling and panels,
removing and installing ......................... 6-8DDimmer switch ...................................... 3-17EEngine break-in ....................................... 5-3
Engine idling speed, checking .............. 6-19
Engine oil and oil filter cartridge ............ 6-11
Engine stop switch ................................ 3-18Engine trouble warning light ................... 3-5
EXUP system ....................................... 3-30
FFinal gear oil ......................................... 6-14
Front and rear brake pads, checking .... 6-24
Front fork, adjusting .............................. 3-26
Front fork, checking .............................. 6-29
Fuel....................................................... 3-22
Fuel consumption, tips for reducing........ 5-3
Fuel level warning light ........................... 3-5
Fuel tank breather/overflow hose ......... 3-24
Fuel tank cap ........................................ 3-21
Fuses, replacing ................................... 6-33HHandlebar switches .............................. 3-17
Hazard switch ....................................... 3-18
Headlight bulb, replacing ...................... 6-34
High beam indicator light ........................ 3-4
Horn switch ........................................... 3-18IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-31
Immobilizer system ................................. 3-1
Immobilizer system indicator light........... 3-6
Indicator lights and warning lights .......... 3-4LLicense plate light bulb, replacing ........ 6-37
Luggage strap holders .......................... 3-30MMain switch/steering lock........................ 3-2
Maintenance and lubrication, periodic .... 6-4
Maintenance, emission control
system .................................................. 6-3
Matte color, caution ................................ 7-1Model label .............................................. 9-1
Multi-function display............................... 3-8
NNeutral indicator light .............................. 3-4OOil level warning light .............................. 3-4PParking .................................................... 5-4
Part locations .......................................... 2-1
Pass switch ........................................... 3-17SSafety information ................................... 1-1
Seats ..................................................... 3-25
Shifting .................................................... 5-2
Shift pedal ............................................. 3-19
Shift timing indicator light ........................ 3-6
Shock absorber assembly, adjusting .... 3-28
Sidestand .............................................. 3-31
Sidestand, checking and lubricating...... 6-28
Spark plugs, checking ........................... 6-10
Specifications .......................................... 8-1
Speedometer unit .................................... 3-7
Starting the engine .................................. 5-1
Start switch............................................ 3-18
Steering, checking................................. 6-29
Storage.................................................... 7-4
Supporting the motorcycle .................... 6-39
Swingarm pivots, lubricating ................. 6-28TTail/brake light ....................................... 6-36
Throttle grip and cable,
checking and lubricating ..................... 6-26
Throttle grip free play, checking ............ 6-19
Tires ...................................................... 6-20
U2S3E2E0.book Page 1 Tuesday, September 21, 2010 10:43 AM