Page 37 of 80
1
2
3
4
5
6
7
8
9
6-2
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU17521
Owner’s tool kitZAUM00**
1
1. Owner’s tool kitThe owner’s tool kit is located inside
the storage compartment under the
seat. (See page 3-10.)
The service information included in
this manual and the tools provided in
the owner’s tool kit are intended to as-
sist you in the performance of preven-
tive maintenance and minor repairs.
However, additional tools such as a
torque wrench may be necessary to
perform certain maintenance work
correctly.TIPIf you do not have the tools or expe-
rience required for a particular job,
have a Yamaha dealer perform it for
you.
2 ( ' K P F F
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"
Page 43 of 80

1
2
3
4
5
6
7
8
9
6-8
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
Panel C
To remove the panelRemove the screws, and then take
the panel off.ZAUM00**
2(✕4)
1
1. Panel C
2. ScrewTo install the panelPlace the panel in the original posi-
tion, and then install the screws.Panel D
To remove the panel
1. Open the seat. (See page 3-10.)ZAUM00**
2
1
1. Panel D
2. Screw2. Remove the quick fasteners by
pushing in the center pin, and
then take the panel off.
To install the panelPlace the panel in the original posi-
tion, and then install quick fasteners.
EAUT1835
Checking the spark plugThe spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause
any spark plug to slowly erode, the
spark plug should be removed and
checked in accordance with the pe-
riodic maintenance and lubrication
chart. In addition, the condition of the
spark plug can reveal the condition of
the engine.
To remove the spark plug
1. Place the vehicle on the center-
stand.
2. Remove panel C. (See page 6-8.)
3. Remove the spark plug cap.
4. Remove the spark plug as
shown, with the spark plug
wrench included in the owner’s
tool kit.
2 ( ' K P F F
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"
Page 46 of 80

1
2
3
4
5
6
7
8
9
6-11
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENTZAUM00**
1
1. Engine oil drain bolt AZAUM00**
1
1. Engine oil drain bolt B4. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
5. Check the O-ring for damage and
replace it if necessary.
6. Install the oil strainer, spring,
O-ring and engine oil drain bolts,
and then tighten the drain bolts to
the specifi ed torque.Tightening torque:
Engine oil drain bolt A:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)
Engine oil drain bolt B:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)TIPMake sure that the O-ring is properly
seated.
7. Refi ll with the specifi ed amount of
the recommended engine oil, and
then install and tighten the engine
oil fi ller cap.Recommended engine oil:
See page 8-1.
Oil change quantity:
0.9 L (0.95 US qt, 0.79 Imp.qt)
ECA11670
NOTICE● Do not use oils with a diesel
speci cation of “CD” or oils of
a higher quality than speci ed.
In addition, do not use oils la-
beled “ENERGY CONSERVING
II” or higher.
● Be sure no foreign material en-
ters the crankcase.
8. Start the engine, and then let
it idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the en-
gine off and check for the cause.
9. Turn the engine off, and then
check the oil level and correct it if
necessary.
10. Reset the oil change tripmeter.
(See page 3-3 for reset proce-
dures.)
TIPIf the engine oil is changed before
the oil change indicator fl ashes (i.e.
before the periodic oil change interval
has been reached), the oil change
tripmeter must be reset after the
oil change for the next periodic oil
change to be indicated at the correct
time.
2 ( ' K P F F
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"
Page 48 of 80