2011 YAMAHA CYGNUS 125 reset

1
2
3
4
5
6
7
8
9
3-2
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
EAUT2111
Keyhole coverZAUM00**
1
1. Keyhole cover leverTo open the keyhole cover
Insert the key bow into the keyhole
cover receptacle as shown, and then
turn the key to the right to open the
cover.
To close the keyhole cover
Push the keyhole cover lever inward
and the keyhole cover will close.
EAU11004
Indicator and warning lightsZAUM00**
RESET
SELECT
1
2
3
1. High beam indicator light “&”
2. Turn signal indicator light “5”
3. Engine trouble warning light “
”
EAU11020
Turn signal indicator light “
5
”
This indicator light fl ashes when the
turn signal switch is pushed to the left
or right.EAU11080
High beam indicator light “&”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAUT1934
Engine trouble warning light “
”
This warning light fl ashes or stays on
if an electrical circuit monitoring the To unlock the steering
12
ZAUM00**1. Turn.
2. Release.Push the key in, and then turn it to
“OFF” while still pushing it.
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"

1
2
3
4
5
6
7
8
9
3-3
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
engine is not working correctly. If this
occurs, have a Yamaha dealer check
the self-diagnosis system.
The electrical circuit of the warning
light can be checked by turning the
key to “ON”. The warning light should
come on for a few seconds, and then
go off.
If the warning light does not come
on initially when the key is turned to
“ON”, or if the warning light remains
on, have a Yamaha dealer check the
electrical circuit.
EAU11601
SpeedometerZAUM00**
RESET
SELECT
1
1. SpeedometerThe speedometer shows the riding
speed.
When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then re-
turn to zero in order to test the electri-
cal circuit.
EAUT1957
Multi-function display
EWA14431
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function display. Changing
settings while riding can distract
the operator and increase the risk
of an accident.ZAUM00**
RESET
SELECT
1
2
3
4
5
6
1. Oil change indicator “7”
2. Odometer
3. Fuel meter
4. “RESET” button
5. “SELECT” button
6. ClockThe multi-function display is equipped
with the following:●
an odometer
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"

1
2
3
4
5
6
7
8
9
3-4
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS●
a tripmeter (which shows the dis-
tance traveled since it was last
set to zero)
●
an oil change tripmeter (which
shows the distance traveled since
the last engine oil change)
●
an oil change indicator (which
fl ashes when the engine oil
should be changed)
●
a clock
●
a fuel meter
TIP●
When the key is turned to “ON”,
all segments of the display come
on for a few seconds. During this
time, the multi-function display is
performing a self-test.
●
Be sure to turn the key to “ON”
before using the “SELECT” and
“RESET” buttons.
Odometer, tripmeter and oil change
tripmeter modes
Pushing the “SELECT” button switch-
es the display among the odom-
eter mode “ODO”, the tripmeter mode
“TRIP” and the oil change tripmeter
“OIL CHANGE TRIP” in the following
order:
ODO → TRIP → OIL CHANGE TRIP
→ ODO
OdometerTIPIf the odometer indicates “-----”, have
a Yamaha dealer check the multi-
function display, as it may be faulty.
Tripmeter
To reset the tripmeter, select it by
pushing the “SELECT” button until
“TRIP” is displayed, and then push the
“RESET” button at least 1 second.TIPIf the tripmeter indicates “-----”, have
a Yamaha dealer check the multi-
function display, as it may be faulty.
Oil change tripmeter
To reset the oil change tripmeter, se-
lect it by pushing the “SELECT” but-
ton until “OIL CHANGE TRIP” is dis-
played, and then push the “RESET”
button at least 3 seconds.
Push the “SELECT” button again to
start the oil change tripmeter; the dis-
play changes to the ODO mode.
Oil change indicator “7”
This indicator fl ashes at the initial
1000 km (600 mi), then at every 3000
km (1800 mi) thereafter to indicate
that the engine oil should be changed.
After changing the engine oil, reset
the oil change tripmeter.
If the engine oil is changed before
the oil change indicator fl ashes (i.e.
before the periodic oil change interval
has been reached), the oil change
tripmeter must be reset after the
oil change for the next periodic oil
change to be indicated at the correct
time.TIP●
If the oil change tripmeter is reset
before the initial 1000 km (600
mi), the next periodic oil change
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"

1
2
3
4
5
6
7
8
9
3-5
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
interval will be at every 3000 km
(1800 mi) thereafter.
●
If the oil change tripmeter in-
dicates “-----”, have a Yamaha
dealer check the multi-function
display, as it may be faulty.
Clock
To set the clock:
1. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
2. When the hour digits start fl ash-
ing, push the “SELECT” button to
set the hours.
3. Push the “RESET” button, and
the fi rst minute digit will start
fl ashing.
4. Push the “SELECT” button to set
the fi rst minute digit.
5. Push the “RESET” button and
the second minute digit will start
fl ashing.
6. Push the “SELECT” button to set
the second minute digit.
7. Push the “RESET” button and
then release it to start the clock.Fuel meter
The fuel meter indicates the amount
of fuel in the fuel tank. The display
segments of the fuel meter disappear
towards “E” (Empty) as the fuel level
decreases. When “
” starts fl ashing,
refuel as soon as possible. When the
key is turned to “ON”, all of the display
segments of the fuel meter will appear
for a few seconds, and then shown
actual fuel level.
EAU12348
Handlebar switchesLeftZAUM00**
3 1
2
1. Dimmer switch “%/&”
2. Turn signal switch “4/6”
3. Horn switch “*”RightZAUM00**
1
1. Start switch “,”
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"

1
2
3
4
5
6
7
8
9
6-10
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAUT1352
Engine oil and oil strainerThe engine oil level should be
checked before each ride. In addition,
the oil must be changed and the oil
strainer cleaned at the intervals speci-
fi ed in the periodic maintenance and
lubrication chart. The engine oil must
also be changed at the initial 1000 km
(600 mi) and when the oil change indi-
cator fl ashes. The oil change tripmeter
must be reset after the initial 1000 km
(600 mi). (See page 3-3 for reset pro-
cedures.)
To check the engine oil level
1. Place the vehicle on the center-
stand. A slight tilt to the side can
result in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Wait a few minutes until the oil
settles, remove the oil fi ller cap,
wipe the dipstick clean, insert it
back into the oil fi ller hole (without
screwing it in), and then remove it
again to check the oil level.
TIPThe engine oil should be between the
minimum and maximum level marks.ZAUM00**
12
1. Maximum level mark
2. Minimum level mark4. If the engine oil is below the mini-
mum level mark, add suffi cient oil
of the recommended type to raise
it to the correct level.
5. Insert the dipstick into the oil fi ller
hole, and then tighten the oil fi ller
cap.
To change the engine oil and clean
the oil strainer
1. Start the engine, warm it up for
several minutes, and then turn it off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil fi ller cap
and drain bolts to drain the oil
from the crankcase.
NOTICE:

When removing the engine oil
drain bolt, the O-ring, spring,
and oil strainer will fall out.
Take care not to lose these
parts.
[ECA10411]
ZAUM00**
1
1. Oil fi ller cap
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"

1
2
3
4
5
6
7
8
9
6-11
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENTZAUM00**
1
1. Engine oil drain bolt AZAUM00**
1
1. Engine oil drain bolt B4. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
5. Check the O-ring for damage and
replace it if necessary.
6. Install the oil strainer, spring,
O-ring and engine oil drain bolts,
and then tighten the drain bolts to
the specifi ed torque.Tightening torque:
Engine oil drain bolt A:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)
Engine oil drain bolt B:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)TIPMake sure that the O-ring is properly
seated.
7. Refi ll with the specifi ed amount of
the recommended engine oil, and
then install and tighten the engine
oil fi ller cap.Recommended engine oil:
See page 8-1.
Oil change quantity:
0.9 L (0.95 US qt, 0.79 Imp.qt)
ECA11670
NOTICE● Do not use oils with a diesel
speci cation of “CD” or oils of
a higher quality than speci ed.
In addition, do not use oils la-
beled “ENERGY CONSERVING
II” or higher.
● Be sure no foreign material en-
ters the crankcase.
8. Start the engine, and then let
it idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the en-
gine off and check for the cause.
9. Turn the engine off, and then
check the oil level and correct it if
necessary.
10. Reset the oil change tripmeter.
(See page 3-3 for reset proce-
dures.)
TIPIf the engine oil is changed before
the oil change indicator fl ashes (i.e.
before the periodic oil change interval
has been reached), the oil change
tripmeter must be reset after the
oil change for the next periodic oil
change to be indicated at the correct
time.
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"