2011 VOLVO V60 key

03 Your driving environment
Starting the engine
03
114
remote control key has been pressed into the
ignition switch.
The steering lock is activated when the driver's
door is opened after the engine has been
switched off.
Key positionsFor information on the remote control key's dif-
ferent key positions, see page 81
ProCarManuals.com

03 Your driving environment
Starting the engine – external battery
03
115 Jump starting
If the battery is flat then the car can be started
with current from another battery.
The following points are recommended when
using a donor battery in order to avoid the risk
of an explosion:
1. Insert the remote control key in key posi-
tion 0, see page 81.
2. Ensure that the donor battery is 12 volt.
3. If the donor battery is in another car, switch
off the donor car's engine in the other car
and ensure that the cars do not touch one
another.
4. Connect the red jump lead to the positive
terminal on the donor battery
.5. Open the clips on the front cover of the
battery in your car and remove the cover,
see page 322.
6. Connect the red jump lead to the battery's
positive terminal
.
7. Connect one end of the black jump lead to
the donor battery's negative terminal
.
IMPORTANT
Connect the start cable carefully to avoid
short circuits with other components in the
engine compartment.
8. Connect the other clamp to an earthing
point, (right-hand engine mounting at the
top, the outer screw head)
. Check that
the jump lead clamps are fixed securely so
that there are no sparks during the starting
procedure.
9. Start the engine of the "donor car". Let the
engine run a few minutes at a speed slightly
higher than idle (1500 rpm).
10. Start the engine of the car with the flat bat-
tery. Do not touch the crocodile clips dur-
ing the start procedure. There is a risk of
sparks forming.11. Remove the jump leads, first the black and
then the red.
Make sure that none of the clamps on the
black jump lead comes into contact with
the battery's positive terminal or the clamp
connected to the red jump lead.
WARNING
The battery can generate oxyhydrogen gas,
which is highly explosive. One spark, which
can be generated if you connect a jump lead
incorrectly, is sufficient to make the battery
explode. The battery contains sulphuric
acid, which can cause serious burns. If the
acid comes into contact with eyes, skin or
clothing, flush with large quantities of water.
If acid splashes into the eyes, seek medical
attention immediately.
ProCarManuals.com

03 Your driving environment
Gearboxes
03
118
The gearbox "winter mode" means that the car
moves off with a lower engine speed and
reduced engine power on the drive wheels.
Kick-downWhen the accelerator pedal is pressed all the
way to the floor (beyond the position normally
regarded as full acceleration) a lower gear is
immediately engaged. This is known as kick-
down.
If the accelerator is released from the kick-
down position, the gearbox automatically
changes up.
Kick-down is used when maximum accelera-
tion is needed, such as for overtaking.
Safety functionTo prevent overrevving the engine, the gearbox
control program has a protective downshift
inhibitor which prevents the kick-down func-
tion.
Geartronic does not permit downshifting/kick-
down which would result in an engine speed
high enough to damage the engine. Nothing
happens if the driver still tries to shift down in
this way at high engine speed – the original
gear remains engaged.
When kick-down is activated the car can
change one or more gears at a time depending
on engine speed. The car changes up when theengine reaches its maximum speed in order to
prevent damage to the engine.
Mechanical gear selector inhibitor
G021351
The gear selector can be moved forward and
back freely between N and D. Other positions
are locked with a latch that is released with the
inhibitor button on the gear selector.
With the inhibitor button depressed the lever
can be moved forwards or backwards between
P, R, N and D.
Automatic gear selector inhibitorThe automatic gearbox has special safety sys-
tems:
Parking position (P)Stationary car with engine running:Keep your foot on the brake pedal when mov-
ing the gear selector to another position.
Electric gear inhibitor – Shiftlock Parking
position (P)
To be able to move the gear selector from P to
other gear positions, the brake pedal must be
depressed and the remote control key must be
in position II, see page 81.
Shiftlock – Neutral (N)If the gear selector is in the N position and the
car has been stationary for at least 3 seconds
(irrespective of whether the engine is running)
then the gear selector is locked.
To be able to move the gear selector from N to
other gear positions, the brake pedal must be
depressed and the remote control key must be
in position II, see page 81.
ProCarManuals.com

03 Your driving environment
Gearboxes
03

* Option/accessory, for more information, see Introduction.119
Deactivating the automatic gear selector
inhibitor
If the car cannot be driven, e.g. due to a flat
battery, the gear selector must be moved from
the P position so that the car can be moved.
Lift the rubber mat in the compartment
behind the centre console and open the
hatch.
Fully insert the key blade. Press the key
blade down and hold (For information on
the key blade, see page 52.)
Move the gear selector from the P position.
Automatic gearbox, Powershift*2
D: Automatic gear positions. M (+/–): Manual gear
positions.
Powershift is a six-stage automatic gearbox
that has double mechanical clutch discs in
contrast to a conventional automatic gearbox.
A conventional automatic gearbox has a
hydraulic torque converter that transfers power
from the engine to the gearbox.
Powershift transmission operates in the same
way and has similar controls and functions as
the Geartronic automatic transmission, descri-
bed in the previous section.
HSAThe HSA (Hill Start Assist) function means that
the pressure in the brake system remains forseveral seconds while the foot is moved from
the brake pedal to the accelerator pedal before
setting off or reversing uphill.
The temporary braking effect releases after
several seconds or when the driver acceler-
ates.
To bear in mindThe transmission's double clutch has overload
protection that is activated if it becomes too
hot, e.g. if the car is held stationary with the
accelerator pedal on an uphill gradient for a
long time.
Overheated transmission causes the car to
shake and vibrate, and the warning symbol illu-
minates and the information display shows a
message. The transmission can also overheat
during slow driving in queues (10 km/h or
slower) on an uphill gradient, or with a trailer
hitched. The transmission cools down when
the car is stationary, with foot brake depressed
and the engine running at idling speed.
Overheating during slow driving in queues can
be avoided by driving in stages: Stop the car
and wait with your foot on the brake pedal until
there is a moderate distance to the traffic
ahead, drive forward a short distance, and then
2Only 4-cyl. model 2.0T.
ProCarManuals.com

03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03
124* Option/accessory, for more information, see Introduction.
Eco Start/Stop DRIVe
General information on Start/Stop
The engine is switched off - it becomes quieter and
cleaner....
Certain engines can be fitted with a
Eco Start/Stop DRIVe function which is acti-
vated during e.g. stationary traffic or waiting at
traffic lights.
The engine's automatic restart sequence runs
so smoothly that it is hardly noticeable that the
engine has actually been switched off. The
experience is that the engine has been running
the whole time but with an extremely quiet and
low idling speed.
The Eco Start/Stop DRIVe function gives the
driver the opportunity for a more active envi-
ronmentally conscious way of driving the car
by means of being able to disengage gear andletting the engine auto-stop, whenever appro-
priate.
Function and operation
Eco Start/Stop DRIVe On/Off.
Illuminates briefly on activation and for text
messages.
The engine is auto-stopped.
The Eco Start/Stop DRIVe function is
activated automatically when the
engine is started with the key. The driver is
made aware of the function by the instrument
panel symbol (2) illuminating briefly and the
green lamp (1) for the On/Off button illuminat-
ing.
NOTE
After starting with the key and each auto-
stop the car must first reach 5 km/h before
the automatic Start/Stop function is re-acti-
vated - following which certain conditions
must also be fulfilled, refer to these under
the heading "The engine does not auto-
stop".
All of the car's normal systems such as lighting,
radio, etc. work as normal even with an auto-
stopped engine, except that some equipment
may have its function temporarily reduced, e.g.
the climate control system's fan speed or
extremely high volume on the audio system.
Auto-stopping the engineIn order that the engine will auto-stop the car
must be stationary:
•Set the gear lever in neutral position and
release the clutch pedal - the engine is
switched off.
As verification and reminder
that the engine is auto-stop-
ped this symbol in the display
(3) illuminates.
Auto-starting the engineWith the gear lever in neutral position:
ProCarManuals.com

03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03

* Option/accessory, for more information, see Introduction.125
•Depress the clutch pedal - the engine
starts.
or
•Depress the accelerator pedal - the engine
starts.
If the car is on a downhill slope:
•Release the foot brake and let the car roll
faster than normal walking pace - the
engine starts.
After which it is only necessary to engage a
gear and continue the journey.
Gear indicator
An essential detail in connection with environ-
mental driving is to drive in the right gear and
change gear in time.The driver is assisted by an indicator which
notifies the driver when it is most advanta-
geous to engage the next higher or lower gear
- GSI (Gear Shift Indicator).
Indication is made with an up or down arrow in
the combined instrument panel's lower dis-
play.
Deactivating the Eco Start/Stop DRIVe
function
In certain situations, it may
advisable to temporarily dis-
engage the automatic
Start/Stop function - this is
carried out with a push of this
button (1).
Disengaged Start/Stop func-
tion is indicated by the infor-
mation display's symbol (2)
going out and the message
Eco DRIVe Off being dis-
played for about 5 seconds -
while the button's lamp goes
out at the same time.
The Start/Stop function is disengaged until it is
reactivated with the button or until the next
time the engine is started with the key.
Limitations
The engine does not auto-stopEven if the Eco Start/Stop DRIVe function is
activated, the engine does not auto-stop if:
•the driver has opened the seatbelt's
buckle.
•the car has not stopped - however, the
Start/Stop function does accept slow roll-
ing, the equivalent to normal walking pace.
•the capacity of the battery is below the
minimum permissible level.
•the engine does not have normal operating
temperature.
•outside temperature is below 0 or above
30 °C.
•the environment in the passenger com-
partment differs from the preset values -
indicated by the ventilation fan running at
a high speed.
•the car has been reversed and reverse gear
is disengaged.
•battery temperature is below 0 °C or above
55 °C.
The engine auto-starts without driver
intervention
An auto-stopped engine may restart in some
cases without the driver having decided that
the journey should continue.
ProCarManuals.com

03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03
126* Option/accessory, for more information, see Introduction.
In the following cases the engine auto-starts
even if the driver has not depressed the clutch
pedal in order to engage a gear:
•Misting forms on the windows.
•Outside temperature is below 0 or above
30 °C.
•There is a temporarily high current take-off
or battery capacity has dropped to the low-
est permissible level.
•The car is rolling faster than the equivalent
normal walking pace.
•Repeated pumping of the brake pedal.
WARNING
Do not open the bonnet when the engine
has auto-stopped - the engine may sud-
denly auto-start. In order to avoid auto-star-
ting with raised bonnet:
•First engage a gear and apply the park-
ing brake or take the remote control key
from the ignition switch.
The engine does not auto-startIn the following cases the engine does not
auto-start after having auto-stopped:
•The driver's seatbelt buckle has been
opened - a display text prompts the driver
to start the engine normally.
•A gear is engaged without declutching - a
display text prompts the driver to set the
gear lever in neutral position in order to
enable auto-start.
Involuntary engine stopIn the event that a start-up fails and the engine
stops, proceed as follows:
1. Depress the clutch pedal again - the engine
starts automatically after the gear lever has
been set in neutral position. Prior to this the
information display showed the text
Set
the gear lever in neutral.
Text messageIn combination with this indicator
lamp the Eco Start/Stop DRIVe func-
tion may display text messages on the infor-
mation display for certain situations. For some
of them there is a recommended action that
should be performed. The following table
shows some examples.
Sym-
bolMessageInfo/Action
Eco DRIVe OnIlluminates for
about 5 seconds
after Eco Start/
Stop DRIVe has
been activated.
Eco DRIVe OffIlluminates for
about 5 seconds
after Eco Start/
Stop DRIVe has
been switched
off.
Disengage to
startThe engine is
ready to auto-
start - waiting
for the clutch
pedal to be
depressed.
Depress the
foot brake to
startThe engine is
ready to auto-
start - waiting
for the brake
pedal to be
depressed.
ProCarManuals.com

03 Your driving environment
Parking brake
03
132
Disengaging the parking brake
Parking brake control.
Cars with manual gearbox
Releasing manually
1. Insert the remote control key in the ignition
switch.
2. Depress the brake pedal firmly.
3. Pull the control.
NOTE
The parking brake can also be released
manually by depressing the clutch pedal
instead of the brake pedal. Volvo recom-
mends the use of the brake pedal.
Releasing automatically1. Start the engine.2. Ease up the clutch and depress the accel-
erator.
Cars with automatic gearbox
Releasing manually
1. Insert the remote control key in the ignition
switch.
2. Depress the brake pedal firmly.
3. Pull the control.
Releasing automatically1. Put the seatbelt on.
2. Start the engine.
3.
Move the gear selector to position D or R
and depress the accelerator.
NOTE
For safety reasons, the parking brake is only
released automatically if the engine is run-
ning and the driver is wearing a seatbelt. The
parking brake is released immediately on
cars with automatic gearbox when the
accelerator pedal is depressed and the gear
selector is in position D or R.
Heavy load uphillA heavy load, such as a trailer, can cause the
car to roll backward when the parking brake is
released automatically on a steep incline.
Avoid this by depressing the control while driv-ing off. Release the control when the engine
achieves traction.
Cars with Keyless drive functionRelease manually by pressing the
START/STOP ENGINE button, then depress
the brake or clutch pedal and pull the control.
Symbols
SymbolSpecification
Read the message on the infor-
mation display
A flashing symbol indicates that
the parking brake is applied. If
the symbol flashes in any other
situation then this means that a
fault has arisen. Read the mes-
sage on the information display.
ProCarManuals.com