2011 SUBARU IMPREZA key

14 Navigation
Before Use
■Points to note before use
Starting the engine before using the system
The navigation system can be used with the ignition key in either the
ON position or the ACC position. To preserve the battery, however, it
should be used with the engine running whenever possible. Using
the system for a long time with the engine off can cause the battery
to run down.
Delay before display of current position
The system will not immediately display a correct indication of your
vehicle's current positio n after being switched on for the first time or
after the battery has been disconnected for a long time. It will display
a correct current position indication as soon as it receives Global Posi-
tioning System (GPS) signals.
Program reloading after battery disconnection
The navigation program will be erased from the system's memory if
the battery is disconnected. If th is happens, load the provided DVD-
ROM disc in the system's main unit and turn the ignition switch to
the ON or ACC position. The system will automatically reload the pro-
gram and start operating normally again.
Incorrect operation on rough roads
The system may operate incorrectly or be unable to read the data on
the DVD-ROM disc when subjected to severe vibration caused by
driving on rough roads.
Handling the GPS antenna
Do not paint the antenna. Doing so could impair or prevent signal
reception. Disabled switches
Some switches are disabled during operation of the system. These
switches are displayed in fainter colors and no messages are dis-
played for them.
Risk of damage to the main unit
Be mindful of the occupant compartment temperature. Using the
system when the occupant compar tment temperature is extremely
high or low can damage it or cause it to malfunction. Also, note that
the system's main unit can be da maged by strong vibration and by
any metallic object or water that gets inside.
Condensation
Condensation can form on the lens inside the main unit when there
is a rapid change in occupant co mpartment temperature (for exam-
ple, when the heater is switched on in cold weather). Such condensa-
tion can cause the system to operate abnormally. If you wait an hour
or so for the condensation to di sappear, the system should start
working normally again. If normal op eration is still not restored after
several hours, we recommend that you contact the nearest SUBARU
dealer.
Replacing the DVD-ROM disc
If you need to replace the DVD-ROM disc, make sure the replacement
disc is compatible with your system's main unit. Inserting an incom-
patible disc could damage the unit.
Impreza_B1962BE-A.book Page 14 Wednesday, May 7, 2008 9:01 PM

Navigation 17
Starting Up the Navigation System
NOTE• To make a selection, touch the desired key displayed on the screen.
• The CAUTION screen remains on the display unless you select .
• When you use the navigation system for the first time, Eastern Standard Time
(EST ) will be displayed. Adjust the syst em's clock to the right time using the
clock setting screen ("SET CLOCK") as described on Page 66.
Impreza_B1962BE-A.book Page 17 Wednesday, May 7, 2008 9:01 PM

20 Navigation
Markers and Controls Displayed on Maps
(8) "Store memory point" keyStores markers on the map.
This key appears just for a few seconds after a map screen is
selected.
(9) Point of interest (POI) key Allows you to display the POI selection screen (See Page 79).
On the screen, you can program POIs to appear on a map as
markers. This key appears just for a few seconds after a map
screen is selected.
(10) Distance from current position Indicates the distance from the current position to the posi-
tion marked by .
(11) Destination/waypoint key Used to program a destination or waypoint at the position
marked by on a scroll screen.
Impreza_B1962BE-A.book Page 20 Wednesday, May 7, 2008 9:01 PM

Navigation 21
Markers and Controls Displayed on Maps
Screens During Route Guidance
(1) Distance and time to destinationIndicates the time (either appro ximate time required or time
of arrival) and the distance to the destination or a waypoint.
(2) Route A thick blue line indicates th e route you should follow.
(3) Turn guidance arrow Indicates the direction of your turn at the next intersection/
intersection as well as the distance to the intersection/inter-
section.
(4) "Repeat voice" key If this key is selected, the last voice guidance will be repeated.
(5) Current road name Shows the name of the road you are currently driving on.
(6) "Display whole route" key If this key is selected, a map co ntaining the entire route will
be displayed. (See Page 56.)
(7) Detour If this key is selected, the syst em will calculate an alternative
route that detours from the current location.
(8) "Change route" key Selecting this key displays the route option menu. Selecting a
new route option causes the system to calculate the selected
route.(3)(2)
(1)
(4)(5)
(6)
(7)
Select the screen
(5 seconds)
(8)
Impreza_B1962BE-A.book Page 21 Wednesday, May 7, 2008 9:01 PM

22 Navigation
Menu Screen Keys and Functions
The table below shows the keys displayed on the MENU screen,
the functions accessible by selecting these keys, and the pages of
this manual that describe the instructions you should follow when
using these functions.
Select to return to
the current map screen.

Navigation 23
Menu Screen Keys and Functions
PhoneBluetooth Phone page 187
Redial List page 199
Received Calls page 199
Phone Book page 201
Memory Points page 193
Bluetooth Settings page 183
Version Version page 87
VOL Volume page 18
Menu screen key Function Reference page
Impreza_B1962BE-A.book Page 23 Wednesday, May 7, 2008 9:01 PM

Navigation 27
Setting Route
Setting Destination
Setting destination/wayp oints by scrolling the
map
Even if you do not know the exact address of your destination or a way-
point on your route to the destination, you can set it by scrolling the
map as follows:
1Touch the screen and scroll the map until the crosshair
reaches the destination or a waypoint.
2Select the (destination or waypoint) key.
The key will separate into the destination key and the waypoint key.
3Select for setting the destination
The system will calculate the route and display the entire route to
the destination on the map.
Select for a waypoint. The system will program the
address of the waypoint on your route (See Page 69). You can set
up to 5 waypoints per trip.
Impreza_B1962BE-A.book Page 27 Wednesday, May 7, 2008 9:01 PM

30 Navigation
Setting Route
You can switch between screens by selecting (next page)
or (previous page).
NOTE• If the set destination area is different from the one displayed under "Search
Area" in the right part of the screen, you must select the (change)
key and specify the desired area again.
• For the methods marked with an asterisk ( * ), you can use the "Change Search
Area" function to narrow the area where a destination or waypoint is located
by selecting the (change) key (See Page 41). •
Depending on the method used or th e status of the map displayed, the
located point may differ from where the facility you want to visit actually
exists.
(Address)* See Page
31.
(Point of Interests)* See Page 34.
(Select from Map) See Page 35.
(Emergency) See Page 37.
(Memory Point) See Page 33.
(Previous Destination) See Page 35.
(Intersection)* See Page 39.
(Freeway Ent/Exit) See Page 36.
(Phone number) See Page 40.
(Coordinates) See Page 38.
(Home) See Page 33.
-(Category1) - (Category5)
Impreza_B1962BE-A.book Page 30 Wednesday, May 7, 2008 9:01 PM