2011 SKODA SUPERB width

technical specifications mirror towing oil change winter tires fuel filter location

Page 71 of 252

SKODA SUPERB 2011 Owner´s Manual WARNING (Continued)■The automatic driving lamp control  only operates as a support and
does not release the driver from his responsibility to check the lights and, if
necessary, to swit

WARNING (Continued)■The automatic driving lamp control  only operates as a support and
does not release the driver from his responsibility to check the lights and, if
necessary, to switch on the light depending on the prevailing light condi-
tions. The light sensor cannot, for example, detect rain or snow. Under
these conditions we recommend switching on the low beam or fog lights!■
Never drive with only the side lights on! The side lights are not bright
enough to light up the road sufficiently in front of you or to be seen by oth-
er oncoming traffic. Therefore always switch on the low beam when it is
dark or if visibility is poor.
Note
The headlights may mist up temporarily. When the driving lights are switched
on, the light outlet areas are free from condensation after a short time, al-
though the headlight lenses may still be misted up around the edge. This mist
has no influence on the life of the lighting system.
Operating the lights and the instrument illumination
Fig. 49
Light switches, knobs for head-
light beam adjustment and
brightness of instrument illumi-
nation
Read and observe on page 67 first.
Switching lights on and off
Depending on the equipment configuration, the light switch
A
» Fig. 49 can be
moved to the following positions.
Turn switch Switching off lights (except daytime running lights)Automatic switching lights on and off » page 70
Switching on the parking light or parking lights » page 73
Switch on low beam
Pull switch
Switch on the front fog lamp » page 71
Switching on the rear fog light » page 71
 Headlight range control
Turning the dial B
» Fig. 49 from the position
 to

gradually adjusts the
headlight range control and thereby shortens the light cone.
The positions of the width of illumination correspond approximately to the fol-
lowing car load.
Front seats occupied, boot empty
All seats occupied, boot empty
All seats occupied, boot loaded
Driver seat occupied, boot loaded
We recommend you adjust the headlight beam when the low beam is switched
on.
 Instrument lighting
Turning the rotary switch
C
» Fig. 49 when the lights are switched on adjusts
the brightness of the instrument lighting » Fig. 49.
The instruments are also illuminated when the parking light, low or high beam light is switched on.
Bi-Xenon headlights
The Bi-Xenon bulbs adapt automatically to the load and driving state of the vehicle when the ignition is switched on and when driving. Vehicles that are
equipped with Bi-Xenon headlights do not have a manual headlight range ad-
justment control.
WARNINGAlways adjust the headlight beam to satisfy the following conditions.■The vehicle does not dazzle other road users, especially oncoming vehi-
cles.■
The beam range is sufficient for safe driving.
Note
■ The light switch is in position  or  and the ignition is turned off, the low
beam is switched off automatically and the status light is lit. The parking light
goes out after the ignition key is removed.■
If there is a fault in the light switch, the low beam illuminates automatically.
68Operation

Page 86 of 252

SKODA SUPERB 2011 Owner´s Manual Raising or lowering the curvature of the lumbar support›Push the switch A in the region of one of the arrows1 » Fig. 67 .
The adjusted driver's seat position can be set in the memory of the
sea

Raising or lowering the curvature of the lumbar support›Push the switch A in the region of one of the arrows1 » Fig. 67 .
The adjusted driver's seat position can be set in the memory of the
seat » page 84 or the remote control key » page 84.
Note
If the setting procedure is interrupted, you will need to press the button again.
Head restraints
Fig. 69
Head restraints: Setting / removing
Fig. 70
Rear centre head rests in vehi-
cles with the TOP TETHER sys-
tem
Read and observe on page 81 first.
Best protection is achieved if the top edge of the head rest is at the same level
as the upper part of your head.
Setting height
›
Grasp the side of the head restraint with both hands and push it upwards as
required » Fig. 69 - 
.
›To move the head restraint downwards, press and hold the safety but-
ton » Fig. 69 -  with one hand and push the head restraint down with the
other hand.
The head restraints and the front seats must be adjusted to match the body
size at all times and the seat belt must always be fastened properly to provide
the most effective levels of protection to the passengers » page 9, Correct and
safe seated position .
Removing/installing›
Fold the seat slightly forward before removing the rear head restraint.
›
Pull the head restraint out of the seat backrest as far as the stop.
›
Press the locking button in the direction of the arrow » Fig. 69 - 
and pull
the head restraint out.
›
To reinsert the head restraint, push it far enough down into the seat back-
rest until the locking button clicks into place.
Removing and installing rear middle head rest
Applies to vehicles using the TOP TETHER system.
›
Pull the head restraint out of the seat backrest as far as the stop.
›
Press the locking button in the direction of arrow
1
» Fig. 70 simultaneously
press the locking button into the opening
2
using a flathead screwdriver
with a width of maximum 5 mm and pull out the head rest.
›
To reinsert the head restraint, push it far enough down into the seat back-
rest until the locking button clicks into place.
WARNINGWith seats occupied, the respective head rests must be installed and cor-
rectly set (may not be in the bottom position) - there is a risk of fatal injury!
Note
The middle rear head restraint is adjustable in two positions.83Seats and practical features

Page 204 of 252

SKODA SUPERB 2011 Owner´s Manual CAUTION■Only use the manual pressure and do not hit the full wheel trim – there is a
risk of damaging the trim.■
When using the anti-theft wheel bolt, ensure that it is in the hole in the
valve

CAUTION■Only use the manual pressure and do not hit the full wheel trim – there is a
risk of damaging the trim.■
When using the anti-theft wheel bolt, ensure that it is in the hole in the
valve area.
■
If wheel trims are fitted, an adequate flow of air must be assured in order to
cool the brake system.
Note
We recommend that you use wheel trims from ŠKODA Original Accessories.
Wheel bolts
Fig. 174
Remove the cap
Read and observe and on page 197 first.
Before removing the wheel bolts, remove the covering caps.
Pulling off
›
Push the extraction pliers » page 205 sufficiently far onto the cap until the
inner catches of the pliers are positioned at the collar of the cap.
›
Remove the cap in the direction of the arrow » Fig. 174.
Fitting
›
Push the cap onto the wheel bolt up to the stop.
Manufacturer-approved tyre variants
 Introduction
This chapter contains information on the following subjects:
Explanation of the tyre labelling
201
Superb
202Superb GreenLine202Superb N1203
Approved tyre variants are first to be selected for the model variant (e.g. Su-
perb GreenLine), and then selected according to the engine size of your vehi-
cle.
If the model variant of your vehicle cannot be found in the discrete module,
then the approved tyre variants are to be selected according to the engine size
of your vehicle in module » page 202, Superb .
Only use radial tyres of the same type, size (rolling circumference) and tread
pattern on one axle on all four wheels.
When mounting new tyres the tyres have to be replaced axle by axle.
The information listed in the table corresponds to the information available at the time of going to press.
The approved tyre / rim combinations for your car are given on the sales and
technical vehicle documentation.
Explanation of the tyre labelling
Explanation of tyre markings
For example, 225/50R 17 91 T means:
225Tyre width in mm50Height/width ratio in %RCode letter for the type of tyre – Radial17Diameter of wheel in inches91Load indexTSpeed symbol
The date of manufacture is stated on the tyre wall (possibly on the inside).
For example, DOT ... 11 14... means, for example, that the tyre was manufac-
tured in the 11th week of 2014.
The marking M+Smeans that the associated tyre is suitable for winter use.
Load index
The load index indicates the maximum permissible load for each individual
tyre. 
201Wheels

Page 233 of 252

SKODA SUPERB 2011 Owner´s Manual Dimensions
Vehicle dimensions for operating weight without driver (in mm) SuperbSuperb GreenLineSuperb CombiSuperb Combi GreenLineLength4833483348334833Width1817181718171817Width including exterior mi

Page 248 of 252

SKODA SUPERB 2011 Owner´s Manual Operation in winter195
Replacing196
Safety instructions193
Vehicle care Alcantara
182
Fabrics182
Synthetic leather182
washing176
Vehicle Condition see Auto Check Control
33
Vehicle data sticker228
Veh

four wheel drive service roof rack service reset tire size fuse chart